show voice port - Tecnológico de Costa Rica
show voice port - Tecnológico de Costa Rica show voice port - Tecnológico de Costa Rica
timing dial-pulse min-delay timing dial-pulse min-delay To specify the time between wink-like pulses for a specified voice port on the Cisco 3600 series, use the timing dial-pulse min-delay voice-port configuration command. Use the no form of this command to reset the default value. timing dial-pulse min-delay milliseconds no timing dial-pulse min-delay milliseconds Syntax Description milliseconds Time, in milliseconds, between the generation of wink-like pulses. Valid entries are numbers from 0 to 5000. Default 300 milliseconds Command Mode Voice-port configuration Usage Guidelines This command first appeared in Cisco IOS Release 11.3(1)T. Use the timing command with the dial-pulse min-delay keyword with PBXes requiring a wink-like pulse, even though they have been configured for delay-dial signaling. If the value for this keyword is set to 0, the router will not generate this wink-like pulse. The call signal direction for this command is in. Example The following example configures the time between the generation of wink-like pulses on a Cisco 3600 series voice port to 350 milliseconds: voice-port 1/0/0 timing dial-pulse min-delay 350 Related Commands You can use the master indexes or search online to find documentation of related commands. timeouts initial timeouts interdigit timing clear-wait timing delay-duration timing dialout-delay timing digit timing interdigit timing pulse timing pulse-interdigit timing wink-duration timing wink-wait Voice Over IP for the Cisco 3600 Series Commands 4-75
timing digit timing digit To specify the DTMF digit signal duration for a specified voice port, use the timing digit voice-port configuration command. Use the no form of this command to reset the default value. timing digit milliseconds no timing digit milliseconds 4-76 Syntax Description milliseconds The DTMF digit signal duration, in milliseconds. Valid entries are numbers from 50 to 100. Supported on FXO, FXS and E&M ports. Default 100 milliseconds Command Mode Voice-port configuration Usage Guidelines This command first appeared in Cisco IOS Release 11.3(1)T. The call signal direction for the timing digit command is out. Examples The following example configures the DTMF digit signal duration on a Cisco 3600 series voice port to 50 milliseconds: voice-port 1/0/0 timing digit 50 Related Commands You can use the master indexes or search online to find documentation of related commands. timeouts initial timeouts interdigit timing clear-wait timing delay-duration timing delay-start timing dial-pulse min-delay timing interdigit timing pulse timing pulse-interdigit timing wink-duration timing wink-wait Voice over IP for the Cisco 3600 Series Software Configuration Guide
- Page 223 and 224: fax-rate fax-rate 4-24 To establish
- Page 225 and 226: icpif icpif 4-26 To specify the Cal
- Page 227 and 228: input gain input gain To configure
- Page 229 and 230: ip udp checksum ip udp checksum 4-3
- Page 231 and 232: non-linear non-linear 4-32 To enabl
- Page 233 and 234: operation operation To select a spe
- Page 235 and 236: port port 4-36 To associate a dial
- Page 237 and 238: eq-qos req-qos 4-38 To specify the
- Page 239 and 240: ing number ring number To specify t
- Page 241 and 242: session target session target 4-42
- Page 243 and 244: show call active voice show call ac
- Page 245 and 246: show call active voice 4-46 Table 4
- Page 247 and 248: show call history voice show call h
- Page 249 and 250: show call history voice 4-50 Table
- Page 251 and 252: show dial-peer voice 4-52 The follo
- Page 253 and 254: show dialplan incall number show di
- Page 255 and 256: show num-exp show num-exp 4-56 To s
- Page 257 and 258: show voice port 4-58 Voice card spe
- Page 259 and 260: show voice port 4-60 Table 4-7 Show
- Page 261 and 262: shutdown (voice-port configuration)
- Page 263 and 264: signal 4-64 Note If you change the
- Page 265 and 266: snmp-server enable traps snmp-serve
- Page 267 and 268: snmp-server enable traps 4-68 The s
- Page 269 and 270: timeouts initial timeouts initial 4
- Page 271 and 272: timing clear-wait timing clear-wait
- Page 273: timing delay-start timing delay-sta
- Page 277 and 278: timing pulse timing pulse To specif
- Page 279 and 280: timing wink-duration timing wink-du
- Page 281 and 282: type type 4-82 To specify the E&M i
- Page 283 and 284: vad vad 4-84 To enable voice activi
- Page 285 and 286: Anexo 4: Guía de antenas y accesor
- Page 287 and 288: Table 26-15: Physical and Environme
- Page 289 and 290: Software Ordering Information Softw
- Page 291 and 292: Installation Notes Installation Not
- Page 293 and 294: Anexo 5: Manual de usuario de los p
- Page 295 and 296: THE SPECIFICATIONS AND INFORMATION
- Page 297 and 298: Contents About the User’s Guide .
- Page 299 and 300: Contents iii Setting the Forwarding
- Page 301 and 302: Chapter 9 - Viewing Statistics Cont
- Page 303 and 304: Appendix A -Aironet 340 Series Brid
- Page 305 and 306: x Aironet 340 Series Bridge Chapter
- Page 307 and 308: xii Aironet 340 Series Bridge Welco
- Page 309 and 310: xiv Aironet 340 Series Bridge Radio
- Page 311 and 312: xvi Aironet 340 Series Bridge Paren
- Page 313 and 314: xviii Aironet 340 Series Bridge The
- Page 315 and 316: Part 1 - Getting Started Part 1 - G
- Page 317 and 318: 1 - 2 Aironet 340 Series Bridge Bef
- Page 319 and 320: 1 - 4 Aironet 340 Series Bridge 2.
- Page 321 and 322: 1 - 6 Aironet 340 Series Bridge Ins
- Page 323 and 324: 1 - 8 Aironet 340 Series Bridge Att
timing dial-pulse min-<strong>de</strong>lay<br />
timing dial-pulse min-<strong>de</strong>lay<br />
To specify the time between wink-like pulses for a specified <strong>voice</strong> <strong>port</strong> on the Cisco 3600 series, use<br />
the timing dial-pulse min-<strong>de</strong>lay <strong>voice</strong>-<strong>port</strong> configuration command. Use the no form of this<br />
command to reset the <strong>de</strong>fault value.<br />
timing dial-pulse min-<strong>de</strong>lay milliseconds<br />
no timing dial-pulse min-<strong>de</strong>lay milliseconds<br />
Syntax Description<br />
milliseconds Time, in milliseconds, between the generation of wink-like pulses. Valid<br />
entries are numbers from 0 to 5000.<br />
Default<br />
300 milliseconds<br />
Command Mo<strong>de</strong><br />
Voice-<strong>port</strong> configuration<br />
Usage Gui<strong>de</strong>lines<br />
This command first appeared in Cisco IOS Release 11.3(1)T.<br />
Use the timing command with the dial-pulse min-<strong>de</strong>lay keyword with PBXes requiring a wink-like<br />
pulse, even though they have been configured for <strong>de</strong>lay-dial signaling. If the value for this keyword<br />
is set to 0, the router will not generate this wink-like pulse. The call signal direction for this<br />
command is in.<br />
Example<br />
The following example configures the time between the generation of wink-like pulses on a<br />
Cisco 3600 series <strong>voice</strong> <strong>port</strong> to 350 milliseconds:<br />
<strong>voice</strong>-<strong>port</strong> 1/0/0<br />
timing dial-pulse min-<strong>de</strong>lay 350<br />
Related Commands<br />
You can use the master in<strong>de</strong>xes or search online to find documentation of related commands.<br />
timeouts initial<br />
timeouts interdigit<br />
timing clear-wait<br />
timing <strong>de</strong>lay-duration<br />
timing dialout-<strong>de</strong>lay<br />
timing digit<br />
timing interdigit<br />
timing pulse<br />
timing pulse-interdigit<br />
timing wink-duration<br />
timing wink-wait<br />
Voice Over IP for the Cisco 3600 Series Commands 4-75