show voice port - Tecnológico de Costa Rica
show voice port - Tecnológico de Costa Rica show voice port - Tecnológico de Costa Rica
shutdown (dial-peer configuration) shutdown (dial-peer configuration) To change the administrative state of the selected dial peer from up to down, use the shutdown dial-peer configuration command. Use the no form of this command to change the administrative state of this dial peer from down to up. shutdown no shutdown Syntax Description This command has no arguments or keywords. Command Mode Dial-peer configuration Usage Guidelines This command first appeared in Cisco IOS Release 11.3(1)T. When a dial peer is shut down, you cannot initiate calls to that peer. This command is applicable to both VoIP and POTS peers. Example The following example changes the administrative state of voice telephony dial peer 10 to down: configure terminal dial-peer voice 10 pots shutdown Voice Over IP for the Cisco 3600 Series Commands 4-61
shutdown (voice-port configuration) shutdown (voice-port configuration) 4-62 To take the voice ports for a specific voice interface card offline, use the shutdown voice-port configuration command. Use the no form of this command to put the ports back in service. shutdown no shutdown Syntax Description This command has no arguments or keywords. Command Mode Voice-port configuration Usage Guidelines This command first appeared in Cisco IOS Release 11.3(1)T. When you enter the shutdown command, all ports on the voice interface card are disabled. When you enter the no shutdown command, all ports on the voice interface card are enabled. A telephone connected to an interface will hear dead silence when a port is shut down. Example The following example takes voice port 1/1/0 offline: configure terminal voice port 1/1/0 shutdown Note The preceding configuration example will shut down both voice ports 1/1/0 and 1/1/1. Voice over IP for the Cisco 3600 Series Software Configuration Guide
- Page 209 and 210: comfort-noise comfort-noise 4-10 To
- Page 211 and 212: cptone cptone 4-12 To configure a v
- Page 213 and 214: description description To include
- Page 215 and 216: destination-pattern 4-16 Related Co
- Page 217 and 218: dial-peer voice dial-peer voice 4-1
- Page 219 and 220: echo-cancel coverage echo-cancel co
- Page 221 and 222: echo-cancel enable echo-cancel enab
- Page 223 and 224: fax-rate fax-rate 4-24 To establish
- Page 225 and 226: icpif icpif 4-26 To specify the Cal
- Page 227 and 228: input gain input gain To configure
- Page 229 and 230: ip udp checksum ip udp checksum 4-3
- Page 231 and 232: non-linear non-linear 4-32 To enabl
- Page 233 and 234: operation operation To select a spe
- Page 235 and 236: port port 4-36 To associate a dial
- Page 237 and 238: eq-qos req-qos 4-38 To specify the
- Page 239 and 240: ing number ring number To specify t
- Page 241 and 242: session target session target 4-42
- Page 243 and 244: show call active voice show call ac
- Page 245 and 246: show call active voice 4-46 Table 4
- Page 247 and 248: show call history voice show call h
- Page 249 and 250: show call history voice 4-50 Table
- Page 251 and 252: show dial-peer voice 4-52 The follo
- Page 253 and 254: show dialplan incall number show di
- Page 255 and 256: show num-exp show num-exp 4-56 To s
- Page 257 and 258: show voice port 4-58 Voice card spe
- Page 259: show voice port 4-60 Table 4-7 Show
- Page 263 and 264: signal 4-64 Note If you change the
- Page 265 and 266: snmp-server enable traps snmp-serve
- Page 267 and 268: snmp-server enable traps 4-68 The s
- Page 269 and 270: timeouts initial timeouts initial 4
- Page 271 and 272: timing clear-wait timing clear-wait
- Page 273 and 274: timing delay-start timing delay-sta
- Page 275 and 276: timing digit timing digit To specif
- Page 277 and 278: timing pulse timing pulse To specif
- Page 279 and 280: timing wink-duration timing wink-du
- Page 281 and 282: type type 4-82 To specify the E&M i
- Page 283 and 284: vad vad 4-84 To enable voice activi
- Page 285 and 286: Anexo 4: Guía de antenas y accesor
- Page 287 and 288: Table 26-15: Physical and Environme
- Page 289 and 290: Software Ordering Information Softw
- Page 291 and 292: Installation Notes Installation Not
- Page 293 and 294: Anexo 5: Manual de usuario de los p
- Page 295 and 296: THE SPECIFICATIONS AND INFORMATION
- Page 297 and 298: Contents About the User’s Guide .
- Page 299 and 300: Contents iii Setting the Forwarding
- Page 301 and 302: Chapter 9 - Viewing Statistics Cont
- Page 303 and 304: Appendix A -Aironet 340 Series Brid
- Page 305 and 306: x Aironet 340 Series Bridge Chapter
- Page 307 and 308: xii Aironet 340 Series Bridge Welco
- Page 309 and 310: xiv Aironet 340 Series Bridge Radio
shutdown (<strong>voice</strong>-<strong>port</strong> configuration)<br />
shutdown (<strong>voice</strong>-<strong>port</strong> configuration)<br />
4-62<br />
To take the <strong>voice</strong> <strong>port</strong>s for a specific <strong>voice</strong> interface card offline, use the shutdown <strong>voice</strong>-<strong>port</strong><br />
configuration command. Use the no form of this command to put the <strong>port</strong>s back in service.<br />
shutdown<br />
no shutdown<br />
Syntax Description<br />
This command has no arguments or keywords.<br />
Command Mo<strong>de</strong><br />
Voice-<strong>port</strong> configuration<br />
Usage Gui<strong>de</strong>lines<br />
This command first appeared in Cisco IOS Release 11.3(1)T.<br />
When you enter the shutdown command, all <strong>port</strong>s on the <strong>voice</strong> interface card are disabled. When<br />
you enter the no shutdown command, all <strong>port</strong>s on the <strong>voice</strong> interface card are enabled. A telephone<br />
connected to an interface will hear <strong>de</strong>ad silence when a <strong>port</strong> is shut down.<br />
Example<br />
The following example takes <strong>voice</strong> <strong>port</strong> 1/1/0 offline:<br />
configure terminal<br />
<strong>voice</strong> <strong>port</strong> 1/1/0<br />
shutdown<br />
Note The preceding configuration example will shut down both <strong>voice</strong> <strong>port</strong>s 1/1/0 and 1/1/1.<br />
Voice over IP for the Cisco 3600 Series Software Configuration Gui<strong>de</strong>