show voice port - Tecnológico de Costa Rica
show voice port - Tecnológico de Costa Rica show voice port - Tecnológico de Costa Rica
connection To specify a connection mode for a specified voice port, use the connection voice-port configuration command. Use the no form of this command to disable the selected connection mode. connection plar string no connection plar string Syntax Description Default The default value for this command is no connection. Command Mode Voice-port configuration Usage Guidelines This command first appeared in Cisco IOS Release 11.3(1)T. Use the connection command to specify a connection mode for a specific interface. Use the connection plar command to specify a PLAR interface. The string you configure for this command is used as the called number for all calls coming in over this voice port. The destination dial peer is determined on the basis of this called number. If the connection command is not configured, the standard session application outputs a dial tone when the interface goes off-hook until enough digits are collected to match a dial-peer and complete the call. Example The following example selects PLAR as the connection mode, with a destination telephone number of 555-9262: voice-port 1/0/0 connection plar 5559262 Related Commands You can use the master index or search online to find documentation of related commands. session-protocol connection plar Specifies a private line auto ringdown (PLAR) connection. PLAR is handled by associating a peer directly with an interface; when an interface goes off-hook, the peer is used to set up the second call leg and conference them together without the caller having to dial any digits. string Specifies the destination telephone number. Valid entries are any series of digits that specify the E.164 telephone number. Voice Over IP for the Cisco 3600 Series Commands 4-11
cptone cptone 4-12 To configure a voice call progress tone locale, use the cptone voice-port configuration command. Use the no form of this command to disable this feature. cptone {australia | brazil | china | france | germany | japan | northamerica | unitedkingdom} no cptone Syntax Description australia Specifies an analog voice interface-related default tone, ring, and cadence setting for Australia. brazil Specifies an analog voice interface-related default tone, ring, and cadence setting for Brazil. china Specifies an analog voice interface-related default tone, ring, and cadence setting for China. finland Specifies an analog voice interface-related default tone, ring, and cadence setting for Finland. france Specifies an analog voice interface-related default tone, ring, and cadence setting for France. germany Specifies an analog voice interface-related default tone, ring, and cadence setting for Germany. japan Specifies an analog voice interface-related default tone, ring, and cadence setting for Japan. northamerica Specifies an analog voice interface-related default tone, ring, and cadence setting for North America. unitedkingdom Specifies an analog voice interface-related default tone, ring, and cadence setting for the United Kingdom. Default The default value for this command is northamerica. Command Mode Voice-port configuration Usage Guidelines This command first appeared in Cisco IOS Release 11.3(1)T. Use the cptone command to specify a regional analog voice interface-related tone, ring, and cadence setting for a specified voice port. This command only affects the tones generated at the local interface. It does not affect any information passed to the remote end of a connection, or any tones generated at the remote end of a connection. Voice over IP for the Cisco 3600 Series Software Configuration Guide
- Page 159 and 160: Configuration Tasks To configure Vo
- Page 161 and 162: Configure RSVP for Voice Enable RSV
- Page 163 and 164: You should configure Multilink PPP
- Page 165 and 166: Enable RTP Header Compression on a
- Page 167 and 168: Frame Relay for Voice over IP Confi
- Page 169 and 170: Table 2-1 Sample Number Expansion T
- Page 171 and 172: Figure 2-5 Outgoing Calls from the
- Page 173 and 174: Configure POTS Peers To configure t
- Page 175 and 176: Configure VoIP Peers Verify Tips Co
- Page 177 and 178: • Call progress tone using the cp
- Page 179 and 180: Fine-Tune FXO and FXS Voice Ports T
- Page 181 and 182: Validation Tips Step Command Purpos
- Page 183 and 184: Step Command Purpose Fine-Tune E&M
- Page 185 and 186: Configure CODEC and VAD for Dial Pe
- Page 187 and 188: Step 8 Click the Up button until th
- Page 189 and 190: Limit TCP Transactions Limit TCP Tr
- Page 191 and 192: Establish Queueing and Congestion S
- Page 193 and 194: Establish Queueing and Congestion S
- Page 195 and 196: Establish Queueing and Congestion S
- Page 197 and 198: Modify the System Buffer Size To di
- Page 199 and 200: Performance Management Examples The
- Page 201 and 202: 4-2 • output attenuation • port
- Page 203 and 204: Command Syntax Conventions Command
- Page 205 and 206: acc-qos 4-6 Example The following e
- Page 207 and 208: answer-address 4-8 Example The foll
- Page 209: comfort-noise comfort-noise 4-10 To
- Page 213 and 214: description description To include
- Page 215 and 216: destination-pattern 4-16 Related Co
- Page 217 and 218: dial-peer voice dial-peer voice 4-1
- Page 219 and 220: echo-cancel coverage echo-cancel co
- Page 221 and 222: echo-cancel enable echo-cancel enab
- Page 223 and 224: fax-rate fax-rate 4-24 To establish
- Page 225 and 226: icpif icpif 4-26 To specify the Cal
- Page 227 and 228: input gain input gain To configure
- Page 229 and 230: ip udp checksum ip udp checksum 4-3
- Page 231 and 232: non-linear non-linear 4-32 To enabl
- Page 233 and 234: operation operation To select a spe
- Page 235 and 236: port port 4-36 To associate a dial
- Page 237 and 238: eq-qos req-qos 4-38 To specify the
- Page 239 and 240: ing number ring number To specify t
- Page 241 and 242: session target session target 4-42
- Page 243 and 244: show call active voice show call ac
- Page 245 and 246: show call active voice 4-46 Table 4
- Page 247 and 248: show call history voice show call h
- Page 249 and 250: show call history voice 4-50 Table
- Page 251 and 252: show dial-peer voice 4-52 The follo
- Page 253 and 254: show dialplan incall number show di
- Page 255 and 256: show num-exp show num-exp 4-56 To s
- Page 257 and 258: show voice port 4-58 Voice card spe
- Page 259 and 260: show voice port 4-60 Table 4-7 Show
cptone<br />
cptone<br />
4-12<br />
To configure a <strong>voice</strong> call progress tone locale, use the cptone <strong>voice</strong>-<strong>port</strong> configuration command.<br />
Use the no form of this command to disable this feature.<br />
cptone {australia | brazil | china | france | germany | japan | northamerica | unitedkingdom}<br />
no cptone<br />
Syntax Description<br />
australia Specifies an analog <strong>voice</strong> interface-related <strong>de</strong>fault tone, ring, and ca<strong>de</strong>nce<br />
setting for Australia.<br />
brazil Specifies an analog <strong>voice</strong> interface-related <strong>de</strong>fault tone, ring, and ca<strong>de</strong>nce<br />
setting for Brazil.<br />
china Specifies an analog <strong>voice</strong> interface-related <strong>de</strong>fault tone, ring, and ca<strong>de</strong>nce<br />
setting for China.<br />
finland Specifies an analog <strong>voice</strong> interface-related <strong>de</strong>fault tone, ring, and ca<strong>de</strong>nce<br />
setting for Finland.<br />
france Specifies an analog <strong>voice</strong> interface-related <strong>de</strong>fault tone, ring, and ca<strong>de</strong>nce<br />
setting for France.<br />
germany Specifies an analog <strong>voice</strong> interface-related <strong>de</strong>fault tone, ring, and ca<strong>de</strong>nce<br />
setting for Germany.<br />
japan Specifies an analog <strong>voice</strong> interface-related <strong>de</strong>fault tone, ring, and ca<strong>de</strong>nce<br />
setting for Japan.<br />
northamerica Specifies an analog <strong>voice</strong> interface-related <strong>de</strong>fault tone, ring, and ca<strong>de</strong>nce<br />
setting for North America.<br />
unitedkingdom Specifies an analog <strong>voice</strong> interface-related <strong>de</strong>fault tone, ring, and ca<strong>de</strong>nce<br />
setting for the United Kingdom.<br />
Default<br />
The <strong>de</strong>fault value for this command is northamerica.<br />
Command Mo<strong>de</strong><br />
Voice-<strong>port</strong> configuration<br />
Usage Gui<strong>de</strong>lines<br />
This command first appeared in Cisco IOS Release 11.3(1)T.<br />
Use the cptone command to specify a regional analog <strong>voice</strong> interface-related tone, ring, and ca<strong>de</strong>nce<br />
setting for a specified <strong>voice</strong> <strong>port</strong>. This command only affects the tones generated at the local<br />
interface. It does not affect any information passed to the remote end of a connection, or any tones<br />
generated at the remote end of a connection.<br />
Voice over IP for the Cisco 3600 Series Software Configuration Gui<strong>de</strong>