G-13.mft parallel - NRI

More documents

Recommendations

Info

MAINTENANCE AND SERVICE G-13.mft totalizer Troubleshooting Problem Totalizer does not accept coin Totalizer accepts coin but no credit is given Malfunctions can occur in all electronic devices. These do not always have to be faults in the device. In many cases the reason is improper connections or incorrect settings. Therefore: please first of all check, whether the malfunction can simply be remedied using the following table: Possible causes No power supply Return lever/button pressed/got stuck Coin runway dirty Coin inhibited Price/time DIL switches set to OFF Coin does not exit the device Remedy, hints • Connect ribbon cable to totalizer and machine correctly • Supply vending maching with voltage Make sure, that return lever/button is not inadvertently pressed Open flight deck and clean coin runway (see section "Cleaning totalizer" in this chapter) • Make sure that (common) inhibit line (pin 2/pin 6) is not activated by machine (see section "Interfaces" in Chap. 8 "Technical data") • Make sure that the coin is not inhibited using the DIL switches on the rear of the device or not only the narrow coin channel is enabled and the normal one is inhibited (see section "Inhibit coin types" in Chap. 4 "Function and operation") Set price(s)/timer time (see section "Set the price(s)/timer time" in Chap. 4 "Function and operation") Make sure that the coin outlet is not jammed by foreign objects or devices connected to the bottom of the totalizer 56 National Rejectors, Inc. GmbH, Buxtehude
G-13.mft totalizer MAINTENANCE AND SERVICE Problem Totalizer accepts coin, but display shows no timer time Possible causes Time DIL switch (S2) set to OFF National Rejectors, Inc. GmbH, Buxtehude Remedy, hints Set timer time (see section "Set the timer time" in Chap. 4 "Function and operation") If the malfunction cannot be remedied, you can use the NRI tester • G-19.0645 (5-digit display, for power supply of 220/230 V, ordering code 16183)/ • G-19.0567 (4-digit display, for power supply of 220/230 V, ordering code 7756)/ • G-19.0650 (5-digit display, for power supply of 110/115 V, ordering code 21410) to test the signal lines of the connecting cable. To remedy other faults please contact our service technicians. 57
Page 1:
Technical Documentation CRANE Elect
Page 4 and 5:
TABLE OF CONTENTS G-13.mft totalize
Page 6 and 7: TABLE OF CONTENTS G-13.mft totalize
Page 8 and 9: GENERAL INFORMATION G-13.mft totali
Page 10 and 11: SAFETY INSTRUCTIONS G-13.mft totali
Page 12 and 13: DESIGN G-13.mft totalizer 3 Design
Page 14 and 15: DESIGN G-13.mft totalizer The coin
Page 16 and 17: DESIGN G-13.mft totalizer Label The
Page 18 and 19: FUNCTION AND OPERATION G-13.mft tot
Page 20 and 21: FUNCTION AND OPERATION (1-/2-PRICE
Page 22 and 23: FUNCTION AND OPERATION (1-/2-PRICE
Page 24 and 25: FUNCTION AND OPERATION (TIMER) G-13
Page 30 and 31: FUNCTION AND OPERATION (TV TOTALIZE
Page 50 and 51: STARTING UP G-13.mft totalizer 5 St
Page 52 and 53: STARTING UP G-13.mft totalizer Inst
Page 54 and 55: STARTING UP G-13.mft totalizer ...
Page 58 and 59: THE PC PROGRAMMING STATION WINEMP G
Page 60 and 61: TECHNICAL DATA G-13.mft totalizer 8
Page 62 and 63: TECHNICAL DATA G-13.mft totalizer I
Page 64 and 65: TECHNICAL DATA G-13.mft totalizer G
Page 66 and 67: TECHNICAL DATA G-13.mft totalizer G
Page 68 and 69: INDEX G-13.mft totalizer Index 1/2-
Page 70 and 71: INDEX G-13.mft totalizer I Inhibit
Page 72 and 73: INDEX G-13.mft totalizer T Teach Co
Page 74 and 75: GLOSSARY G-13.mft totalizer ECV Ele
show all

G-13.mft parallel - NRI

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?