XONE 3D USER GUIDE Carey proofed
XONE 3D USER GUIDE Carey proofed XONE 3D USER GUIDE Carey proofed
+10! +6 +3 0 -3 -6 -10 OFF +6 FILTER XFADE 1X Y 2 OFF CUE -15 -20 FX1 FX2 LEVEL HF MF LF 0 +6 0 +6 LINE A LINE B -10 +10 OFF OFF OO PRE +6 +6 MIXER SECTION — CHANNEL INPUT SC 1 - 2 1 1 3 2 4 1 2 3 4 FX 1-2 send controls These controls adjust the signal level that is sent from each channel to the two FX mix busses. These signals will appear at the RCA sockets on the rear of the unit. FX1 PRE switch determines whether the FX1 send signal is affected by the channel fader. When pressed the signal is prefader, when released post-fader. FX1 can also be sent to the input of the soundcard for processing or recording by the PC (see Soundcard Mode for details). FX2 is pre-fader (this can be changed internally - see User Options). FX2 can also be selected as the audio source for the Auto Beat detector (See BPM Detector). Input Selection Two switches select one of three possible stereo audio sources; Line A (RIAA phono on CH 2–4), Line B, or output from the computer via the internal soundcard (SC1- 6). Switch 2 (SC) overrides switch 1 (phono/line). The led indicator displays which source is active: CH1 CH2 CH3 CH4 Switch1 gn LineA Phono Phono Phono Switch1 red LineB LineB LineB LineB Switch2 red SC1-2 SC3-4 SC5-6 SC1-2 Channel Level Control This control has a range of +/- 10dB either side of the 0dB centre position. Use it to adjust the signal level of an audio source to give a nominal 0dB reading on the channel meter, with the peak level at or below +6dB. Turn LEVEL down if the +10 peak meter starts flashing. Channel Equalizer/Isolator The Xone:3D is equipped with a very powerful 3 band EQ stage providing a controlled +6dB of boost when fully clockwise, but full isolation (cut) of each band for dramatic effect when fully anticlockwise. Centre frequencies are set at: HF = 10kHz (high frequency, treble) MF = 1.2kHz (mid frequency) LF = 120Hz (low frequency, bass) Allen & Heath 12 XONE:3D User Guide
7 +10! +6 +3 0 -3 -6 -10 OFF +6 FILTER XFADE 1X Y 2 OFF CUE -15 -20 FX1 FX2 LEVEL HF MF LF 0 +6 0 +6 LINE A LINE B -10 +10 OFF OFF OO PRE +6 +6 MIXER SECTION — CHANNEL INPUT SC 1 - 2 1 5 6 8 5 6 7 8 Filter/Crossfade Assignment The channel signal can be routed directly to the main mix or via either of the two filter/crossfade paths. Note that the crossfade affects the filter path only. Set the 3-position switch to its mid position to route the signal direct to the mix, or to its left or right positions to route the signal to filter-1/crossfade-X or filter-2/crossfade-Y respectively. To enable the crossfader check that the XFADE ON switch above the filter1 controls is pressed. Cue Switch Press the cue switch to listen to the channel pre-fade signal in the headphones and see its level on the main meters. The led indicator ring around the switch lights when selected. The big red CUE ACTIVE indicator also lights to warn that you are monitoring the channel signal rather than the main mix. Press the switch to deselect cue. The switches are interlocked; pressing another one turns off the previous selection. Channel Meter Displays the channel signal level. It is pre-EQ and pre-fader. This means it is not affected by the EQ or fader position. The channel level control should be set so that the meter averages around ‘0’ with loudest peaks no higher than ‘+6’. Turn down the level control if the +10 peak indicator lights. Channel Fader A high quality, smooth travel dual-rail fader adjusts the channel signal level from fully off to fully on. Allen & Heath 13 XONE:3D User Guide
- Page 1 and 2: USER GUIDE Publication AP6388 Allen
- Page 3 and 4: SOFTWARE INSTALLATION STOP! BEFORE
- Page 5 and 6: CONTENTS Congratulations on purchas
- Page 7 and 8: INTRODUCTION TO THE XONE:3D Welcome
- Page 9 and 10: DESCRIPTION BPM COUNTER— Displays
- Page 11: SOUNDCARD OPERATING MODES To config
- Page 15 and 16: DEPTH 1 2 1+2 ASSIGN XFADE RES 4 3
- Page 17 and 18: FRONT CONTROLS & CONNECTORS PHONES
- Page 19 and 20: CAUTION WARNING: FOR CONTINUED PROT
- Page 21 and 22: MIDI PULL MIX MODE 3 2 1 BPM OFF 4
- Page 23 and 24: MIDI PULL MIX MODE 3 2 1 BPM OFF 4
- Page 25 and 26: MAP 1 MAP 2 MIDI CONTROL SECTION MI
- Page 27 and 28: Note No. (Hex) MIDI NOTE CHART Note
- Page 29 and 30: OPERATING LEVELS It is most importa
- Page 31 and 32: adapter CABLES AND CONNECTIONS Slee
- Page 33 and 34: RTN2 FL2R USER OPTIONS FX1 and FX2
- Page 35 and 36: REPLACING THE CROSSFADER Replacing
- Page 37 and 38: MIXER TROUBLESHOOTING If things don
- Page 39 and 40: SOUNDCARD AND MIDI TROUBLESHOOTING
- Page 41 and 42: 6. The configuration utility will n
7<br />
+10!<br />
+6<br />
+3<br />
0<br />
-3<br />
-6<br />
-10<br />
OFF<br />
+6<br />
FILTER<br />
XFADE<br />
1X<br />
Y 2<br />
OFF<br />
CUE<br />
-15<br />
-20<br />
FX1<br />
FX2<br />
LEVEL<br />
HF<br />
MF<br />
LF<br />
0 +6<br />
0 +6<br />
LINE A<br />
LINE B<br />
-10 +10<br />
OFF<br />
OFF<br />
OO<br />
PRE<br />
+6<br />
+6<br />
MIXER SECTION — CHANNEL INPUT<br />
SC 1 - 2<br />
1<br />
5<br />
6<br />
8<br />
5<br />
6<br />
7<br />
8<br />
Filter/Crossfade Assignment<br />
The channel signal can be routed directly<br />
to the main mix or via either of the two<br />
filter/crossfade paths. Note that the<br />
crossfade affects the filter path only.<br />
Set the 3-position switch to its mid<br />
position to route the signal direct to the<br />
mix, or to its left or right positions to<br />
route the signal to filter-1/crossfade-X or<br />
filter-2/crossfade-Y respectively.<br />
To enable the crossfader check that the<br />
XFADE ON switch above the filter1<br />
controls is pressed.<br />
Cue Switch<br />
Press the cue switch to listen to the channel<br />
pre-fade signal in the headphones and see its<br />
level on the main meters. The led indicator<br />
ring around the switch lights when selected.<br />
The big red CUE ACTIVE indicator also<br />
lights to warn that you are monitoring the<br />
channel signal rather than the main mix.<br />
Press the switch to deselect cue. The<br />
switches are interlocked; pressing another<br />
one turns off the previous selection.<br />
Channel Meter<br />
Displays the channel signal level. It is pre-EQ<br />
and pre-fader. This means it is not affected<br />
by the EQ or fader position.<br />
The channel level control should be set so<br />
that the meter averages around ‘0’ with<br />
loudest peaks no higher than ‘+6’. Turn<br />
down the level control if the +10 peak<br />
indicator lights.<br />
Channel Fader<br />
A high quality, smooth travel dual-rail fader<br />
adjusts the channel signal level from fully off<br />
to fully on.<br />
Allen & Heath 13 <strong>XONE</strong>:<strong>3D</strong> User Guide
Change language