Standard Bus Procurement Guidelines - APTAStandards.com

More documents

Recommendations

Info

Standard Bus Procurement Guidelines 5.1.5.3 CAPACITY Baseline: Use for 40-ft length bus with baseline seats and baseline seating arrangement. Also see Section 5.4.7.5.4.5 Rated capacity of the bus shall be no less than 43 seated passengers, not including the operator, with the standard seating arrangement. Alternative: Use for alternative configurations as noted. Also see Section 5.4.7.5.4.5 Rated capacity of the bus shall be no less than_ (Procuring Agency to insert number of Seated Passengers for specified seating arrangement)__ seated passengers, not including the operator, with the specified seating arrangement. Note: 5.1.5.4 SERVICE LIFE AND MAINTENANCE 5.1.5.4.1 Service Life Subtract {mfr. data} seats for 35 ft length with baseline or padded seating in baseline arrangement. Subtract {mfr. data} seats for 35 ft length with baseline or padded seating in perimeter arrangement. Subtract{mfr. data} seats for 35-ft length with cushioned seating in baseline arrangement. Subtract{mfr. data} seats for 35-ft length with cushioned seating in perimeter arrangement. Subtract{mfr. data} seats for 40 ft length with baseline or padded seating in perimeter arrangement. Subtract{mfr. data} seats for 40-ft length with cushioned seating in baseline arrangement. Subtract {mfr. data} seats for 40-ft length with cushioned seating in perimeter arrangement. Technical Specifications 128 10/18/07
Standard Bus Procurement Guidelines The bus shall be designed to operate in transit service for at least 12 years or 500,000 miles. It shall be capable of operating at least 40,000 miles per year including the twelfth year. 5.1.5.4.2 Maintenance and Inspection Scheduled maintenance or inspection tasks as specified by the Contractor shall require a skill level of 3M or less. Scheduled maintenance tasks shall be related and shall be grouped in maximum mileage intervals. Base upon the Design Operating Profile defined in Section 5.1.2, routine scheduled maintenance actions, such as filter replacement and adjustments, shall not be required at intervals of less than 6,000 miles, except for engine oil/filter change intervals for severe duty shown below and routine daily service performed during the fueling operations. Higher levels of scheduled maintenance tasks shall occur at even multiples of mileage for lower level tasks. The Contractor may require routine scheduled maintenance actions at shorter intervals when a more severe operating profile is anticipated. APTA Comment: The table below added per committee agreement at Chicago meeting. 5.1.5.4.3 Accessibility SEVERE DUTY OIL/FILTER CHANGE INTERVAL Average Vehicle Speed Oil/Filter Change Interval MPH Miles 10 and higher 6000 8 – 10 5000 6 – 8 4000 4 – 6 3000 2 - 4 1500 All systems or components subject to periodic maintenance or that are subject to periodic failures shall be readily accessible for service and inspection. To the extent practicable, removal or physical movement of components unrelated to the specific maintenance and/or repair tasks involved shall be unnecessary. As a goal, relative accessibility of components, measured in time required to gain access, shall be inversely proportional to frequency of maintenance and repair of the components. Specific maintainability requirements are defined in other sections of Part 5: Technical Specifications. 5.1.5.4.4 Interchangeability Components with identical functions shall be interchangeable to the extent practicable. These components shall include passenger window hardware, interior trim, lamps, lamp lenses, and seat assemblies. Components with nonidentical functions shall not be, or appear to be, interchangeable. Any one component or unit used in the construction of these buses shall be an exact duplicate in design, manufacture, and assembly for each bus in this Contract. Technical Specifications 129 10/18/07
Page 1:
American Public Transit Association
Page 6 and 7:
Standard Bus Procurement Guidelines
Page 8 and 9:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91: Standard Bus Procurement Guidelines
Page 118 and 119: 1. 2. 3. 4. 5. 6. 7. 8. Standard Bu
Page 120 and 121: 1. 2. Standard Bus Procurement Guid
Page 139: Standard Bus Procurement Guidelines
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209:
show all

Standard Bus Procurement Guidelines - APTAStandards.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?