CLI Guide - WatchGuard Technologies

More documents

Recommendations

Info

CHAPTER 3: Configuration Mode Commands Enable high availability WG#config WG(config)#high_availability WG(config-ha)$ [active_standby | active_active] [advanced] Enter Advanced Setting Mode [disable] [hotsync] [monitor ] [ [interface N ip ] | [-name systemName2] ] [no][shared_secret secret1] show show current configuration and statistics history show command history exit go back to parent level top go back to root level Effect Enables high availability in WatchGuard appliances with one or more HA interfaces, and assists you in entering precise HA system settings. Arguments active_standby | active_active This turns high availability on in either Active/ Standby mode or Active/Active mode. For more information on these modes, see the Vcontroller User Guide. advanced This enters advanced High Availability configuration mode, and shows the following prompt: WG(config-ha-advanced)$ 74 WatchGuard Vclass 5.1
Second level configuration mode commands For more information, see “High Availability advanced configuration mode” on page 77 disable Disables High Availability. hotsync Syncs the local appliance with its peer. In Active/ Standby mode a hotsync should be performed every time the configuration of the Active box is changed. In Active/Active mode, a hotsync should only be performed during the initial setup, when the secondary appliance is in factory default configuration. monitor {1 & | 2} This optional command specifies which interface (1 or 2) you want this appliance to monitor for link status. (Note that the 0 (private) interface is always being monitored.) [interface N ip ] | [-name systemName2] ] [no][shared_secret secret1] ha1_interface \ This command configures the IP address of the HA1 interface of the master and backup appliances. ha2_interface \ This command configures the IP address of the WatchGuard Command Line Interface Guide 75
Page 1 and 2:
WatchGuard ® Command Line Interfac
Page 3 and 4:
WatchGuard Technologies, Inc. Fireb
Page 5 and 6:
4. Limited Warranty. WATCHGUARD mak
Page 7 and 8:
6. Export Controls. You agree not t
Page 9 and 10:
Contents Contents .................
Page 11 and 12:
CHAPTER 3 Configuration Mode Comman
Page 13 and 14:
CHAPTER 5 Other Commands ..........
Page 15 and 16:
CHAPTER 1 Using the Command Line In
Page 17 and 18:
CLI limitations CLI Guide text conv
Page 19 and 20:
Getting started with the WatchGuard
Page 21 and 22:
Page 23 and 24:
Case sensitivity Getting started wi
Page 25 and 26:
Page 27 and 28:
Navigating through the CLI Getting
Page 29 and 30:
Arguments None. Example WG(admin)#e
Page 31 and 32:
Page 33 and 34:
Installing and configuring a WatchG
Page 35 and 36:
Command Description Installing and
Page 37 and 38: Installing and configuring a WatchG
Page 39 and 40: CHAPTER 2 Administration Mode Comma
Page 41 and 42: Administration mode commands plete
Page 43 and 44: Administration mode commands 4 Clic
Page 45 and 46: Administration mode commands #ex: e
Page 47 and 48: crl command Administration mode com
Page 49 and 50: Administration mode commands Merge
Page 51 and 52: Administration mode commands Proces
Page 53 and 54: Administration mode commands Shuts
Page 55 and 56: CHAPTER 3 Configuration Mode Comman
Page 57 and 58: abort command Top-level configurati
Page 59 and 60: certificate command Top-level confi
Page 61 and 62: Top-level configuration mode comman
Page 63 and 64: interface command Top-level configu
Page 65 and 66: Arguments None Example WG#config WG
Page 67 and 68: [no] traffic command (log level) WG
Page 75 and 76: as command Top-level configuration
Page 81 and 82: Second level configuration mode com
Page 87: Example Second level configuration
Page 105 and 106: Arguments Second level configurati
Page 137 and 138: Level 3 configuration mode commands
Page 139 and 140:
Level 3 configuration mode commands
Page 141 and 142:
CHAPTER 4 Debug Mode Commands All W
Page 143 and 144:
arp command Debugging/troubleshooti
Page 145 and 146:
Debugging/troubleshooting commands
Page 147 and 148:
- images/rs_sublogo.gif Debugging/t
Page 149 and 150:
pppoe_config command Debugging/trou
Page 151 and 152:
Page 153 and 154:
set_dos_if command Debugging/troubl
Page 155 and 156:
Page 157 and 158:
CHAPTER 5 Other Commands No command
Page 159 and 160:
Show address command Display curren
Page 161 and 162:
Show all_routes command WG#show all
Page 163 and 164:
Effect Displays any DNS configurati
Page 165 and 166:
Show command component, action or p
Page 167 and 168:
Show command Effect Displays whethe
Page 169 and 170:
Show command Arguments This argume
Page 171 and 172:
Show command Arguments This argume
Page 173 and 174:
Show command Effect Displays the ba
Page 175 and 176:
Index A abbreviations 8 abort syste
Page 177 and 178:
administration mode disable 108 CLI
Page 179 and 180:
log configuration, level 3 commands
Page 181:
X xml export debugging information
show all

CLI Guide - WatchGuard Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?