CLI Guide - WatchGuard Technologies
CLI Guide - WatchGuard Technologies CLI Guide - WatchGuard Technologies
CHAPTER 4: Debug Mode Commands rs_kdiag command WG#debug WG(debug)rs_kdiag Effect This command displays internal diagnostics information. Arguments None 138 WatchGuard Vclass 5.1
set_dos_if command Debugging/troubleshooting commands WG#debug WG(debug)set_dos_if [show | set | set_default | -h | -? ], where show Show the current settings. set xyzv Set DOS protection on interfaces. x,y,z,v must be 0 or 1. x is for interface 0, y for interface 1, z for interface 2, and v for interface 3. set_default Restore the setting to the factory default value Effect This sets denial of service (DOS) protection on individual interfaces. The default settings are 0000000f. Example WG#debug WG(debug)set_dos_if set 0011 slink command WG#debug WG(debug)# slink [ [-s] ] [show] -s : save configuration only Port: eth0, eth1, eth2, eth3 Mode: auto = Auto negotiate 1000A = 1000BaseFX, AutoNegotiation enabled 1000H = 1000BaseFX, AutoNegotiation disabled 100F = 100BaseT, Full-duplex mode 100H = 100BaseT, Half-duplex mode 10F = 10BaseT, Full-duplex mode 10H = 10BaseT, Half-duplex mode show: current setting Effect This command sets the physical speed of a specific accelerated data interface. Arguments etho, eth1, eth2, eth3 Indicates the interface to be changed. mode auto = Auto negotiate WatchGuard Command Line Interface Guide 139
- Page 101 and 102: Second level configuration mode com
- Page 103 and 104: Second level configuration mode com
- Page 105 and 106: Arguments Second level configurati
- Page 107 and 108: Second level configuration mode com
- Page 109 and 110: Second level configuration mode com
- Page 111 and 112: Second level configuration mode com
- Page 113 and 114: Second level configuration mode com
- Page 115 and 116: Second level configuration mode com
- Page 117 and 118: Second level configuration mode com
- Page 119 and 120: Second level configuration mode com
- Page 121 and 122: Second level configuration mode com
- Page 123 and 124: Second level configuration mode com
- Page 125 and 126: Second level configuration mode com
- Page 127 and 128: Second level configuration mode com
- Page 129 and 130: Second level configuration mode com
- Page 131 and 132: Second level configuration mode com
- Page 133 and 134: Second level configuration mode com
- Page 135 and 136: Second level configuration mode com
- Page 137 and 138: Level 3 configuration mode commands
- Page 139 and 140: Level 3 configuration mode commands
- Page 141 and 142: CHAPTER 4 Debug Mode Commands All W
- Page 143 and 144: arp command Debugging/troubleshooti
- Page 145 and 146: Debugging/troubleshooting commands
- Page 147 and 148: - images/rs_sublogo.gif Debugging/t
- Page 149 and 150: pppoe_config command Debugging/trou
- Page 151: Debugging/troubleshooting commands
- Page 155 and 156: Debugging/troubleshooting commands
- Page 157 and 158: CHAPTER 5 Other Commands No command
- Page 159 and 160: Show address command Display curren
- Page 161 and 162: Show all_routes command WG#show all
- Page 163 and 164: Effect Displays any DNS configurati
- Page 165 and 166: Show command component, action or p
- Page 167 and 168: Show command Effect Displays whethe
- Page 169 and 170: Show command Arguments This argume
- Page 171 and 172: Show command Arguments This argume
- Page 173 and 174: Show command Effect Displays the ba
- Page 175 and 176: Index A abbreviations 8 abort syste
- Page 177 and 178: administration mode disable 108 CLI
- Page 179 and 180: log configuration, level 3 commands
- Page 181: X xml export debugging information
CHAPTER 4: Debug Mode Commands<br />
rs_kdiag command<br />
WG#debug<br />
WG(debug)rs_kdiag<br />
Effect<br />
This command displays internal diagnostics<br />
information.<br />
Arguments<br />
None<br />
138 <strong>WatchGuard</strong> Vclass 5.1