Untitled - Zippy

More documents

Recommendations

Info

Page 29 of 92 IEC 60950-1 / EN 60950-1 Clause Requirement – Test Result – Remark Verdict 4.7.2.1 Parts requiring a fire enclosure With having the following components: Components in primary circuits Insulated wiring Components in secondary (not supplied by LPS) the fire enclosure is required. However, with this equipment is for building-in, compliance shall be evaluated for the final system. 4.7.2.2 Parts not requiring a fire enclosure Fire enclosure is required. N 4.7.3 Materials P 4.7.3.1 General See below. P 4.7.3.2 Materials for fire enclosures See appended table 1.5.1. P 4.7.3.3 Materials for components and other parts outside fire enclosures 4.7.3.4 Materials for components and other parts inside fire enclosures Compliance to be evaluated for the final system. Internal components except small parts are V-2 or better. 4.7.3.5 Materials for air filter assemblies No air filter assemblies. N 4.7.3.6 Materials used in high-voltage components No high voltage component. N 5 ELECTRICAL REQUIREMENTS AND SIMULATED ABNORMAL CONDITIONS P 5.1 Touch current and protective conductor current P 5.1.1 General See sub-clauses 5.1.2 to 5.1.6. P 5.1.2 Equipment under test (EUT) Every module has its own mains supply, therefore EUT has multiple mains connections. 5.1.3 Test circuit Using test circuit of figure 5A. P 5.1.4 Application of measuring instrument Using measuring instrument of annex D.1. 5.1.5 Test procedure The touch current was measured from primary to metal chassis. 5.1.6 Test measurements See appended table 5.1.6. P Test voltage (V) ...................................................: Ditto. ⎯ Measured touch current (mA) ..............................: Ditto. ⎯ Max. allowed touch current (mA) .........................: Ditto. ⎯ TRF No.:IECEN60950_1B TRF originator: SGS Fimko N N P P P P
Page 30 of 92 IEC 60950-1 / EN 60950-1 Clause Requirement – Test Result – Remark Verdict Measured protective conductor current (mA) ......: ⎯ Max. allowed protective conductor current (mA) .: ⎯ 5.1.7 Equipment with touch current exceeding 3.5 mA : Touch current did not exceed 3.5 mA. 5.1.8 Touch currents to and from telecommunication networks and cable distribution systems and from telecommunication networks 5.1.8.1 Limitation of the touch current to a telecommunication network and a cable distribution system No TNV circuit connection provided. No TNV circuit connection provided. Test voltage (V) ...................................................: ⎯ Measured touch current (mA) ..............................: ⎯ Max. allowed touch current (mA) .........................: ⎯ 5.1.8.2 Summation of touch currents from telecommunication networks ................................: No TNV circuit connection provided. 5.2 Electric strength P 5.2.1 General See below. P 5.2.2 Test procedure See appended table 5.2. P 5.3 Abnormal operating and fault conditions P 5.3.1 Protection against overload and abnormal operation For output overload test the most unfavourable load is tested. DC fan locked and ventilation openings blocked tested. See appended table 5.3. 5.3.2 Motors All DC fans are approved components. 5.3.3 Transformers With the shorted output of the transformers T1 the unit shuts down and for T2 the unit shuts down, except for +5VSB circuit. 5.3.4 Functional insulation .............................................: Method c). Result of the short tests see appended table 5.3 and annex C. See in appended table 5.3. 5.3.5 Electromechanical components No electromechanical component except for DC fan provided. 5.3.6 Simulation of faults See appended table 5.3. P TRF No.:IECEN60950_1B TRF originator: SGS Fimko N N N N P P P P N
Page 3 and 4: Particulars: test item vs. test req
Page 5 and 6: M1W4-5B40P3w w=V, H M1W4-5600P3w w=
Page 7 and 8: Copy of marking plate(s): Page 6 of
Page 9 and 10: Page 8 of 92 TRF No.:IECEN60950_1B
Page 11 and 12: Page 10 of 92 TRF No.:IECEN60950_1B
Page 13 and 14: Page 12 of 92 IEC 60950-1 / EN 6095
Page 29: Page 28 of 92 IEC 60950-1 / EN 6095
Page 49 and 50: Page 48 of 92 1.5.1 TABLE: list of
Page 51 and 52: Varistors (VZ2, VZ3, VZ4) (optional
Page 53 and 54: Power Module for: 1. M1W4-K40P3w, M
Page 55 and 56: Page 54 of 92 F1 -- 90 1644 18.32 1
Page 57 and 58: Page 56 of 92 F1 -- 90 2804 31.31 3
Page 59 and 60: Location Voltage (V) Note(s): Page
Page 61 and 62: Page 60 of 92 U5 pin 4 to pin 1 172
Page 63 and 64: Test voltage (airflow direction) Pa
Page 65 and 66: Page 64 of 92 C2 body 68.5 100 L2 c
Page 67 and 68: Page 66 of 92 Inlet pin 59.0 46.7 7
Page 69 and 70: Page 68 of 92 4.6.1, 4.6.2 Table: e
Page 71 and 72: 16. U6 pin 1 to 2 Page 70 of 92 s-c
Page 73 and 74: Page 72 of 92 48. Fan Stall 240 8mi
Page 75 and 76: Page 74 of 92 Thickness 0.8mm Elect
Page 77 and 78: Page 76 of 92 National Differences
Page 79 and 80: Page 78 of 92 National Differences
Page 81 and 82:
Page 80 of 92 National Differences
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93:
show all

Untitled - Zippy

Create successful ePaper yourself

Delete template?

Save as template?