installation instructions creative wall „Typ 1“
installation instructions creative wall „Typ 1“
installation instructions creative wall „Typ 1“
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>installation</strong> <strong>instructions</strong> <strong>creative</strong> <strong>wall</strong> <strong>„Typ</strong> <strong>1“</strong><br />
<strong>creative</strong> <strong>wall</strong> ® <strong>„Typ</strong> <strong>1“</strong> sheet 1/6<br />
detail<br />
detail<br />
Flughafenstr. 4 A<br />
D-27809 Lemwerder<br />
Telefon: +49(0)421 -69 35 2 - 0<br />
Telefax: +49(0)421 -69 35 2 - 14<br />
info@procedes.de<br />
www.procedes.de
<strong>installation</strong> <strong>instructions</strong> <strong>creative</strong> <strong>wall</strong> <strong>„Typ</strong> <strong>1“</strong><br />
<strong>installation</strong> <strong>instructions</strong> for <strong>creative</strong> <strong>wall</strong> ®<br />
1) Screw the footplate 380 (an weighting plate 360 if necessary) or footplate 200<br />
to the column.<br />
2) Fit grub screw in stud for tensioning block and insert the groove in the column - one stud<br />
for top and bottom.<br />
3) In the case or multi-part section rails, connect hanging rails with a tube insert to form<br />
a continuous upper and lower rail.<br />
4) Insert tensioning blocks in the centre groove of the rail and roughly align.<br />
5) Arrange upper section rail on the floor in the same position as the <strong>creative</strong> <strong>wall</strong> ® is to later<br />
stand in the room.<br />
Place columns in the required position along the laid out rail (if the fabric <strong>wall</strong> is not freestanding,<br />
now secure column to floor with Spax - footplate 200 (see Fig. 1)).<br />
6) Raise upper section rail, push the upper bolt to the approximate height and put the tension<br />
block onto the preassembled bolt - then connect bolt and tension block wih the tensioning<br />
screws and fix it.<br />
Flughafenstr. 4 A<br />
D-27809 Lemwerder<br />
Telefon: +49(0)421 -69 35 2 - 0<br />
Telefax: +49(0)421 -69 35 2 - 14<br />
sheet 2/6<br />
7) Stand the roll of fabric on its end with the print subject facing forward. Carefully insert the<br />
upper hollow hem with the hose insert in the upper section rail already suspendend while slowly<br />
unrolling the fabric.<br />
8) Bring the lower section rail into the lower seam of the fabric. Then bring the lower bolt to the<br />
approximate height and stick the tension block onto the preassembled bolt - then connect bolt and<br />
tension block with the slit screw and fix it.<br />
9) Align upper section rail exactly straight. Pull fabric taut in the upper/lower section rail and<br />
secure at both ends with the final retention screw.<br />
10) In order to tighten the fabric tear the lower (lose) section rail down. Then tighten the lower<br />
tension block again.<br />
11) Fit end caps on ends of rails.<br />
12) Preassemble hammer head screw with the flat knurled nut in hanging rail: Turn screw 90 O and<br />
secure with the flat knurled nut.<br />
Fit lamp on hanging rail with preassembled hammer head screw and tighten withe knurled nut.<br />
Connect 230 V power cable and if necessary interconnect extension/distributor block.<br />
info@procedes.de<br />
www.procedes.de
<strong>installation</strong> <strong>instructions</strong> <strong>creative</strong> <strong>wall</strong> <strong>„Typ</strong> <strong>1“</strong><br />
cross section<br />
accessories<br />
Flughafenstr. 4 A<br />
D-27809 Lemwerder<br />
clamping block<br />
column<br />
shank core end cap profile 46/20/3<br />
base 380<br />
bolt<br />
set screw<br />
slotted screw<br />
Telefon: +49(0)421 -69 35 2 - 0<br />
Telefax: +49(0)421 -69 35 2 - 14<br />
binder<br />
sheet 3/6<br />
link-screw<br />
info@procedes.de<br />
www.procedes.de
<strong>installation</strong> <strong>instructions</strong> <strong>creative</strong> <strong>wall</strong> <strong>„Typ</strong> <strong>1“</strong><br />
1<br />
2<br />
2x M12/30<br />
(countersunk socket screw)<br />
M5/16<br />
woodscrew<br />
2x M12/20<br />
3<br />
4<br />
Flughafenstr. 4 A<br />
D-27809 Lemwerder<br />
4x M5/8<br />
Telefon: +49(0)421 -69 35 2 - 0<br />
Telefax: +49(0)421 -69 35 2 - 14<br />
sheet 4/6<br />
info@procedes.de<br />
www.procedes.de
<strong>installation</strong> <strong>instructions</strong> <strong>creative</strong> <strong>wall</strong> <strong>„Typ</strong> <strong>1“</strong><br />
5<br />
7<br />
Flughafenstr. 4 A<br />
D-27809 Lemwerder<br />
8<br />
5<br />
2.<br />
Telefon: +49(0)421 -69 35 2 - 0<br />
Telefax: +49(0)421 -69 35 2 - 14<br />
1.<br />
sheet 5/6<br />
M5/20<br />
3.<br />
M5/20<br />
info@procedes.de<br />
www.procedes.de
<strong>installation</strong> <strong>instructions</strong> <strong>creative</strong> <strong>wall</strong> <strong>„Typ</strong> <strong>1“</strong><br />
9<br />
12<br />
flat knurled nut<br />
5.<br />
3.<br />
2.<br />
1.<br />
M5/8<br />
M5/8<br />
knurled screw<br />
4.<br />
T-headed screw<br />
10<br />
11<br />
Flughafenstr. 4 A<br />
D-27809 Lemwerder<br />
1.<br />
Telefon: +49(0)421 -69 35 2 - 0<br />
Telefax: +49(0)421 -69 35 2 - 14<br />
sheet 6/6<br />
info@procedes.de<br />
www.procedes.de<br />
2.
Change language