Mike Solari of Gore - LiveUpdater
Mike Solari of Gore - LiveUpdater
Mike Solari of Gore - LiveUpdater
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Implementation<br />
A newsletter from C B Norwood Distributors Ltd’s Equipment Division Issue No. 16 Autumn 2010<br />
®<br />
Congratulations to<br />
<strong>Mike</strong> <strong>Solari</strong><br />
<strong>of</strong> <strong>Gore</strong><br />
on obtaining the<br />
World Wheat Yield<br />
Record for the<br />
2009 Season
C U S T O M E R P R O F I L E<br />
Contractors fizzing<br />
with new Lemken and Fella gear<br />
Martinborough based contractors Colton Bros Limited are in<br />
total agreement about the benefits their new Lemken Rubin<br />
disc cultivator and Fella TS4000 rake are delivering to their<br />
business. Colton Bros Limited was formed more than 40 years<br />
ago and is today owned and operated by Jim Alpe, Philip Reid,<br />
Rob Gawith, Doug Colton and Warren and Sharon Colton. The<br />
business <strong>of</strong>fers a full agricultural service, including spraying,<br />
ploughing, cultivating, drilling, regrassing, grass and maize<br />
silage, hay baling, grain harvesting and cartage.<br />
The owners purchased a 5.0m Lemken Rubin cultivator in<br />
October from Norwood Farm Machinery Centre in Masterton,<br />
after demonstrating a smaller model last autumn. “We trialled<br />
a 3.0m three-point linkage model and we liked the concept,<br />
so we decided to buy the bigger one, which folds up for<br />
transport,” Jim says.<br />
“It’s a straw incorporator and is an exceptional machine.<br />
We’re most impressed with the job it does. We got it for our<br />
autumn work but we utilised it in the spring time for jobs we<br />
thought it would be handy for. It really improved our seed bed<br />
preparation. Some <strong>of</strong> the paddocks were ex-fodder crop and<br />
we went straight in and levelled then drilled them.”<br />
The Lemken Rubin is a versatile disc harrow with working<br />
widths from 2.5m to 12m, depending on whether it is mounted<br />
or semi-mounted. It is ideal for incorporating tall stubble, green<br />
manure crops, and vegetable waste. The Rubin features two<br />
rows <strong>of</strong> scalloped discs <strong>of</strong> 610mm diameter, 6mm thick with<br />
spring auto reset protection, and two integrated straw harrows<br />
to give an even flow <strong>of</strong> trash through the machine.<br />
Jim believes the Lemken Rubin did a far better job than tandem<br />
discs, because <strong>of</strong> the crumbler roller on the back. “Instead<br />
<strong>of</strong> burning barley, wheat or maize stubble we disced it with the<br />
Rubin and then roller drilled our grass seed over the top. It’s<br />
especially good when you get damp seasons like we’re having<br />
and trouble with burning <strong>of</strong>f stubble. Last year we had a lot <strong>of</strong><br />
barley stubble that got wet and we couldn’t burn it. That’s why<br />
we trialled the small machine and bought this one.”<br />
Philip Reid is also pleased with the job the Lemken has done<br />
and says they’re looking forward to their autumn cultivation<br />
work, which will involve incorporating stubble and preparing<br />
ground for regrassing after crops. “It seems to be easy to set<br />
up and it does the job very nicely,” he says. “We’ve demonstrated<br />
various brands that were fully mounted and we decided<br />
that the trailed version would be more suitable for us, plus it’s<br />
wider so you can cover more area. That side <strong>of</strong> it is very user<br />
friendly for the tractors and it seems to track nicely.”<br />
Colton Bros also purchased a Fella TS4000 rake in October<br />
– the first Fella rake the business has owned. Jim and Philip<br />
decided to buy the rake after visiting the Fella factory in Europe.<br />
“We liked the robustness <strong>of</strong> the construction,” Jim says. “I’ve<br />
looked at other rakes and they tend to be very over complicated,<br />
with a lot <strong>of</strong> electrics and hydraulics, which makes the cost<br />
<strong>of</strong> the machine more expensive for what you get. This TS4000<br />
rake has only two hydraulic services and everything else is<br />
manually operated, which also makes it better for potential<br />
breakdowns.”<br />
Colton Bros has suffered a lot <strong>of</strong> broken tines with other<br />
rakes over the years. “We’ve used this one for the season and<br />
there’s no sign <strong>of</strong> any broken tines. With one brand we had<br />
tines breaking almost daily.”<br />
Philip agrees the Fella rake<br />
has been quite a revelation. “We<br />
always thought it would be nice to<br />
get into a four-rotor rake and it’s<br />
proving very successful. We’ve<br />
used it in a number <strong>of</strong> situations,<br />
mainly in front <strong>of</strong> our self-propelled<br />
chopper for fine-chop silage. We’ve<br />
also used it in front <strong>of</strong> a round baler<br />
and silage baler and it’s proved very<br />
successful.”
Lemken continues to expand range<br />
Since 1780 the Lemken name has been synonymous with<br />
innovation and quality in cultivation equipment. The recent<br />
opening <strong>of</strong> a 20,000,000 Euro paint facility combined with<br />
the launch <strong>of</strong> a range <strong>of</strong> new products continues to place the<br />
German manufacturer at the forefront <strong>of</strong> efficient cultivation<br />
technology.<br />
Famous for its Opal range <strong>of</strong> ploughs, Lemken has now<br />
added the Juwel and Tansanit which feature fully integrated<br />
hydraulic trip mechanisms for truly non-stop operation. The<br />
new Juwel range is designed for the pr<strong>of</strong>essional contractor<br />
looking to utilise 200 plus horsepower in a mounted reversible<br />
plough, whilst the Tansanit shares the same features but in a<br />
hybrid mounted/trailed combination up to seven furrows.<br />
Essentially a semi-mounted plough, the Tansanit uses a<br />
hydraulic top link controlled by pressure sensors which are set<br />
by the operator to add weight to the rear <strong>of</strong> the tractor, thus<br />
enabling a smaller tractor to be utilised.<br />
The well proven Zirkon power harrow range has been<br />
extended with the addition <strong>of</strong> a completely new model, the<br />
Zirkon 8 series. Designed for use with tractors up to 180<br />
horsepower, the Zirkon 8 is available in four working widths<br />
from 2.5 to 4.0m in a rigid format and the option <strong>of</strong> a two speed<br />
gearbox and reversible quick change tines. The most obvious<br />
feature <strong>of</strong> the new Zirkon 8 range is the sloping pr<strong>of</strong>ile <strong>of</strong> the<br />
top <strong>of</strong> the gear trough to prevent the build up <strong>of</strong> soil.<br />
Closely spaced, small diameter rotors produce a very<br />
consistent seedbed and this combined with a choice <strong>of</strong> seven<br />
roller options enable the Zirkon 8 to be specified to suit all soil<br />
types and finish requirements.<br />
Shallow cultivation and incorporation <strong>of</strong> crop residues<br />
continue to become more popular as the benefits to soil<br />
structure and moisture retention are appreciated. Adoption <strong>of</strong><br />
minimum tillage techniques require careful consideration as<br />
well as the equipment required to do an efficient job in one or<br />
two passes.<br />
PRODUCT NEWS<br />
Incorporation <strong>of</strong> high levels <strong>of</strong> crop residue such as grain<br />
maize and chopped straw require a machine with an aggressive<br />
mode <strong>of</strong> action to chop residue and penetrate hard soils, yet<br />
with a sufficiently close disc spacing to prevent the formation<br />
<strong>of</strong> large clods which require further breaking down. It is in this<br />
role that the Lemken Rubin continues to excel.<br />
Two rows <strong>of</strong> large diameter (620mm) scalloped discs set<br />
at a very aggressive angle, mounted on coil spring protected<br />
arms perform the job superbly in all conditions, and will take<br />
stones in its stride. Fitted with a roller from one <strong>of</strong> the largest<br />
ranges available from any manufacturer, the Rubin will create<br />
the perfect stale seedbed with optimum residue incorporation<br />
and consolidation.<br />
In addition, the Heliodor is a lighter disc type incorporator<br />
with slightly smaller discs individually mounted on leaf springs<br />
again for stony conditions. Available with a hydraulic levelling<br />
board and a choice <strong>of</strong> rollers, the Heliodor is perfect for the<br />
incorporation <strong>of</strong> lighter residues such as wheat/barley stubble<br />
etc and is perfect for use in conjunction with a small air seeder<br />
such as the StocksAG TurboJet for the establishment <strong>of</strong> fodder<br />
crops etc.<br />
The Solitair seed drill continues to be the machine <strong>of</strong> choice<br />
with many operators, particularly those who appreciate the<br />
benefit <strong>of</strong> a power harrow/drill combination for its flexibility<br />
and ability to cope with virtually all conditions.<br />
The Lemken seed drill range has now been further<br />
enhanced with the addition <strong>of</strong> the Compact Solitair which<br />
combines the benefits <strong>of</strong> the Heliodor disc system, levelling<br />
board, tyre packer and a new hydraulically controlled coulter<br />
system in one machine. Be it in a ploughed or reduced tillage<br />
system, the Compact Solitair <strong>of</strong>fers the ultimate in seeding<br />
flexibility.
C U S T O M E R P R O F I L E<br />
Fella grass gear does the business<br />
Foxton farmer and contractor Dave Evans has a strong<br />
affiliation with the Fella brand. Dave owns a fleet <strong>of</strong> top-quality<br />
Fella machinery that he uses on his supplement farm and in<br />
his contracting business, AR Evans Limited. The contracting<br />
operation does direct drilling, cultivation, hay, baleage and<br />
individual wrapping.<br />
He has used Fella rakes for more than five years and says he<br />
really likes the brand. “Fella gear is robust. It hasn’t let us down<br />
and it’s good value for money,” Dave says. His most recent<br />
purchase is a Fella 401 Trans mower, which he just bought this<br />
season from Norwood Farm Machinery Centre in Palmerston<br />
North. “The 401 Trans does the business. It’s 4.0m wide, and<br />
for the price we paid for it, it was good value. We’ve only had<br />
3.5m bar mowers in the past,” Dave says. “You can take the<br />
conditioners <strong>of</strong>f and use the 401 Trans as a bar mower and<br />
you can put a roller conditioner on it as well. It has three uses<br />
if you want to utilise it that way.”<br />
Also new this season is a Fella TH1101 trailed tedder. While<br />
Dave has owned a 9.0m tedder in the past, this new machine<br />
is a lot bigger, at 10.7m wide. “It’s been excellent, really<br />
good. We wouldn’t have got the job done this year without it<br />
because <strong>of</strong> the conditions. It has been pretty wet and cloudy<br />
all summer.”<br />
(From left): Bruce Picard (Norwood Farm Machinery Centre,<br />
Palmerston North), Corey Symes, Dave Evans (Evans Contracting)<br />
and Stefan Sprock (Fella, Germany)<br />
Dave says the Foxton region has had a significantly lower<br />
number <strong>of</strong> hay making days than usual this season. “We’ve<br />
had to get a lot done when the sun was shining. The width <strong>of</strong><br />
the TH1101 is great for that – it covers the ground quickly and<br />
follows it well.”<br />
A year ago Dave purchased a Fella TS671 double-rotor<br />
swather, which replaced an identical Fella swather he owned<br />
previously. “The previous one we had for four seasons. It was<br />
a good machine. It was the same as this one, as we got a good<br />
deal and traded it in,” he says. “The new one does a good job<br />
and we can use it for the small baler or the big one. It has good<br />
floating ability. We rake the sand hills and ridges with it, which<br />
can be a bit rough on gear. We rake them and bale them and<br />
the rake floats over the rough ground very well. It’s a good test<br />
for gear in Foxton because <strong>of</strong> the undulating sand country.”<br />
Dave also owns a Fella TS801 double-rotor swather,<br />
which he bought four years ago. While it’s been an excellent<br />
machine, he thinks he’ll probably replace it next season. “It’s<br />
a lot bigger than the 671 but on a light crop you can close it<br />
up for the conventional baler,” he says. “It even floats better<br />
over the ground. They’re a really good machine and you can’t<br />
kill them.”<br />
A TH800 trailed tedder completes AR Evans’ fleet <strong>of</strong> Fella<br />
machinery. The tedder has three-point linkage and is just over<br />
a year old. Dave says it’s been a good machine and is well<br />
suited to light crops. “It’s just broken a few tines but it’s been<br />
a trying season. The crops have been heavy and when we’ve<br />
had to go for it the pressure has been on a bit. It’s really handy<br />
for the smaller paddocks.”
Trans Series Mowers<br />
TH Series Tedders<br />
TS Series Swathers<br />
Harvesting energy with experience<br />
Talk to your<br />
local Fella dealer today<br />
for the best indent deals<br />
for the coming season<br />
Phone 0800 667 9663 to find your local Fella dealer www.fella.co.nz<br />
MS1118
The latest edition <strong>of</strong> ‘Vaderstad News 2010’ highlighting their<br />
ever increasing range <strong>of</strong> cultivation and drilling machinery is<br />
now available.<br />
Vaderstad’s core driving force is the development and<br />
creation <strong>of</strong> flexible machines for cultivation and drilling that<br />
provide considerable economic and agronomic benefits<br />
whatever the cropping system used.<br />
All Vaderstad drills carry out several operations in a single<br />
pass and have a legendary work capacity, in doing so saving<br />
time, energy and money. The long lifetime <strong>of</strong> Vaderstad drills<br />
and their high resale value make them very cost effective and<br />
produce low machine running costs.<br />
The concept <strong>of</strong> fewer passes and shallower cultivation<br />
favours good soil structure and increases earthworm numbers;<br />
a factor that is essential in maintaining and increasing soil<br />
NEW RELEASE<br />
Vaderstad News<br />
2010<br />
fertility, yield capacity and moisture retention.<br />
The 2010 News booklet highlights upgrades in several <strong>of</strong><br />
their existing models and introduces new models <strong>of</strong> both the<br />
highly successful Rapid and Spirit drills.<br />
All Vaderstad drill families now feature the new Interactive<br />
Depth Control which monitors seed depth from the tractor<br />
cab.<br />
The well proven Topdown has benefited from a unique<br />
new Vaderstad invention, the Low Disturbance Point which<br />
is designed for deep cultivation <strong>of</strong> heavy and sometimes wet<br />
soils. In doing so, the Topdown can provide the opportunity<br />
to keep beneficial residues near the surface in addition to<br />
alleviating any sub-surface compaction.<br />
To receive your free copy either email your postal address<br />
to implementation@norwood.co.nz or phone 0800 667 9663.
Canterbury dairy farmers Peter and Arjen Schouten’s new<br />
Vaderstad Rapid RDA600 drill has allowed them to take greater<br />
control over their drilling operation. The Schoutens run a 680ha<br />
irrigated dairy operation near Christchurch, and lease a further<br />
485ha <strong>of</strong> irrigated land. They currently milk 2200 cows.<br />
They previously owned a small drill for pasture drilling and used<br />
contractors to help with the rest but they decided to purchase<br />
a larger drill in order to do more <strong>of</strong> the work themselves. “We<br />
looked at a lot <strong>of</strong> drill options before purchasing the Rapid RDA600<br />
drill at the start <strong>of</strong> this season,” Peter says.<br />
“We thought the Vaderstad was probably the way to go.<br />
Norwood Farm Machinery Centre in Christchurch was the<br />
dealer and we’ve had dealings with them in the past, they do<br />
all our tractor servicing and we’ve had a very good working<br />
relationship with them. That swayed us.”<br />
The Schoutens sowed 600 ha with the drill this season,<br />
starting with barley crops. “We also did a couple <strong>of</strong> pasture<br />
products and we got a maize kit fitted to it and drilled 56 ha <strong>of</strong><br />
maize. The kit was fitted by Norwood Christchurch and allowed<br />
us to drill maize at 60cm spacings.” Peter says the result was<br />
the best crops he has ever had.<br />
He and Arjen chose the RDA600 model because their tractor<br />
could handle its size and they haven’t been disappointed with<br />
the drill’s performance. “The drill is fitted with system discs for<br />
additional cultivation and incorporation <strong>of</strong> crop residues such<br />
as barley stubble.”<br />
C U S T O M E R P R O F I L E<br />
Rapid drill quickly makes a difference<br />
to dairy operation<br />
The Vaderstad Rapid’s specially hardened scalloped discs<br />
(410mm diameter) cut powerfully down into the soil and<br />
provide the Rapid with its ability to drill in the most variable<br />
conditions. The discs and seed coulters efficiently clear straw<br />
from the seed zone. No pan is created during cultivation and<br />
the discs do not have to be adjusted to maintain drilling depth.<br />
Peter says the drill has definitely lived up to his expectations.<br />
“It’s fair to say it’s met our expectations and then some,<br />
particularly in its sheer capacity and accuracy <strong>of</strong> the seed<br />
placement.”<br />
A pneumatic distribution system delivers seed to the<br />
RDA600’s Rapid coulter system, which takes care <strong>of</strong> the<br />
accurate seed placement that is characteristic <strong>of</strong> all Rapid<br />
models. The unique depth control allows drilling to be carried<br />
out at high speed, which gives an impressive capacity .The<br />
seed hopper has a total volume <strong>of</strong> 6000 litres. For wheat, this<br />
means about 25 ha <strong>of</strong> drilling per refill.<br />
“There are many options on the drill that we don’t actually<br />
use,” Peter says. “There are a lot <strong>of</strong> features that if you’re a<br />
cropping farmer you could use. Next season we’ll drill the same<br />
number <strong>of</strong> hectares with it. There’s been some inquiry from<br />
our neighbour to see if we want to do some drilling for them<br />
but we’re pretty happy just here.”
C U S T O M E R P R O F I L E<br />
Lemken combo does the work<br />
<strong>of</strong> two machines<br />
Central Hawkes Bay contractor Kevin Hermansen’s new<br />
Lemken power harrow-seeding unit combination is helping<br />
him keep on top <strong>of</strong> his heavy ground preparation and drilling<br />
workload. Hermansen Contracting Limited undertakes a full<br />
range <strong>of</strong> agricultural work, as well as direct drilling, hay and<br />
baleage.<br />
The company acquired a new Lemken 5.0m power harrow<br />
and drill combination late last year. It is the first Lemken power<br />
harrow the company has owned. “We wanted to buy a drill<br />
that was going to put seed down in the ground and do it<br />
accurately,” Kevin says. “We liked the Lemken’s accuracy, its<br />
strength, its build and the overall quality <strong>of</strong> the machine. It’s<br />
been pretty well built.”<br />
Hermansen Contracting has used the power harrow<br />
primarily for sowing brassica crops and they have also put<br />
some cereal crops in with it. This autumn they are starting to<br />
sow grass seed with it. “It does a good job and we’ve had a<br />
good result. I’m very happy all round. It works well with what<br />
we’re trying to do,” Kevin says.<br />
He particularly likes the accuracy <strong>of</strong> the computer that<br />
controls the seed rate and speed <strong>of</strong> the machine. “We’re trying<br />
to do two jobs at once accurately and both things are being<br />
done properly. Previously we were doing two passes with two<br />
separate machines for power harrowing and drilling, but now<br />
we’re doing both jobs in one pass which is saving us a huge<br />
amount <strong>of</strong> time.” Kevin estimates the power harrow will do<br />
1000 to 1200 hectares this season. “Being able to do it in one<br />
pass is making a huge difference and it compares quite well<br />
to the job we would’ve done with two separate machines.”<br />
Hermansen Contracting has also recently bought a Fella<br />
TS801 double-rotor swather from Norwood Farm Machinery<br />
Centre in Hastings. Kevin says the swather appears to be well<br />
built. It is the first Fella swather he has owned. “We like the<br />
build <strong>of</strong> it – it’s nice and simple and strong and it’s doing a good<br />
job. There is a lot <strong>of</strong> strength in the main pivot points.”<br />
The TS801 has a working width <strong>of</strong> 8m, with the rotors<br />
folding automatically to the lowest transport position. The<br />
swath board also folds automatically for transport. The machine<br />
has universal floating linkage for ground contour adaptation<br />
and features four rotor carriage wheels close to the tines for<br />
maximum contour protection.
Built to do more than the lion’s share!<br />
Rubin – Heliodor – Zirkon – Opal<br />
Talk to your local Lemken dealer about<br />
indent details for the coming season<br />
One <strong>of</strong> Europe’s leading manufacturers <strong>of</strong> soil cultivation,<br />
sowing and plant protection systems<br />
THE AGROVISION COMPANY<br />
Phone 0800 667 9663 to find your local Lemken dealer www.lemken.co.nz<br />
Subsoilers Ploughs Furrow Presses Cultivators Power Harrows Seed Drills Sprayers<br />
MS1110
This Sulky invention has been designed to fit DPX fertiliser<br />
spreaders on farms using “precision farming” techniques. It<br />
leads the way to fertiliser economies by improved applications<br />
in each field, especially on headlands, borders, corners and<br />
irregular areas.<br />
Sulky observed that, even though today with a standard<br />
centrifugal spreader, there is a quality pattern spread and it<br />
can be improved.<br />
So, even with a proportional drive system and GPS guidance,<br />
there is, especially on borders and field angles, a number<br />
<strong>of</strong> small zones with above or below the target rate. In actual<br />
fact, if the overall rate is correct to within the nearest kg/ha,<br />
over 20% <strong>of</strong> the area covered will have received slightly either<br />
above or below the required application rate!<br />
Once this was observed, Sulky fitted a DPX fertiliser spreader<br />
with electric control actuators (working width, rate shutter<br />
control, TRIBORD on borders).<br />
The machine was then automated with the specific development<br />
<strong>of</strong> an area management technique (GPS) <strong>of</strong> the fertiliser<br />
applications onto the soil. This innovation has only seen<br />
the light <strong>of</strong> day thanks to the Sulky DPX setting system that<br />
NEW RELEASE<br />
EcoVision System for optimum in-field<br />
granulated fertiliser applications<br />
uses a variable chute to steplessly adjust the working width.<br />
EcoVision makes a diagnosis, in real time, <strong>of</strong> the distance from<br />
the previous pass as well as the quantities already applied during<br />
this pass. It then optimizes the spread pattern by calculating the<br />
opposite graph <strong>of</strong> that previously spread on the field. Therefore,<br />
depending on the fields characteristics, it adapts the dose (a<br />
function which is combined with the rate proportional and onthe-move<br />
rate modulation functions) and the fertiliser pattern<br />
applied to the field so as to optimise the application.<br />
Thus, at the same required rate, the EcoVision device is able<br />
to reduce by a factor <strong>of</strong> 3 the areas with an overdose within<br />
the same field compared to a standard spread even under GPS<br />
guidance. With the EcoVision, the fertiliser spreader becomes<br />
automatic and is capable <strong>of</strong> adapting to real in-field conditions:<br />
irregular shaped fields, driving errors, field corners, bends, headlands…<br />
Therefore, it greatly reduces all the environmental impacts,<br />
and <strong>of</strong>fers many advantages on the agronomic side (reduced<br />
lodging, better protein content…), on the economic<br />
side (even yields and better fertiliser use) as well as<br />
the ergonomic side (ease <strong>of</strong> use).
Due to the increasing demand for large diet mixers with<br />
a capacity to feed more than 300 cows, JF-STOLL has<br />
now extended the product range. The new range <strong>of</strong><br />
Feeder VM diet mixers consists <strong>of</strong> 3-auger feeders with<br />
a capacity <strong>of</strong> 32-45m³ with cross conveyor for feeding.<br />
To date JF-STOLL has had great success with the<br />
sale <strong>of</strong> large 3-auger Feeders VM with side doors. Now<br />
models with cross conveyor for feeding <strong>of</strong> very large<br />
herds are also available. The new range with cross<br />
conveyor is based on the same concept as the side<br />
door model, apart from the fact that the chassis is longer<br />
to make room for the cross conveyor. This also means<br />
that the machines are based on the modular concept<br />
and can be tailored to the specific needs <strong>of</strong> the farmer.<br />
If the herd is increased the Feeder can be enlarged from<br />
e.g. 32 m³ to 45 m³ without investing in a new Feeder.<br />
The Feeder VM can be equipped with elevator, top for<br />
increased capacity, advanced remote control etc.<br />
JF-STOLL is the biggest and also the leading supplier<br />
<strong>of</strong> complete diet mixers in Northern Europe. The<br />
major part <strong>of</strong> the production is exported all over the<br />
world. Since there are many different markets, JF-<br />
STOLL has built up a large and wide product range <strong>of</strong><br />
vertical auger mixers.This means that JF-STOLL today<br />
<strong>of</strong>fers complete diet mixers with capacities for 35-350<br />
dairy cows, available with cross conveyor or discharge<br />
doors. Furthermore, JF-STOLL <strong>of</strong>fers a wide range <strong>of</strong><br />
optional equipment.<br />
PRODUCT NEWS<br />
3-auger diet mixers<br />
with cross conveyor<br />
VM<br />
1 auger 2 augers 3 augers<br />
Doors Cross conveyor Doors Cross conveyor Doors<br />
Compact Normal Normal Compact Compact Normal Normal Normal Normal<br />
Volume VM-1 S VM-1 VM-1 B VM-2 SB VM-2 S VM-2 VM-2 B VM-3 B VM-3<br />
6.5 m3 VM 6.5-1 S<br />
8 m3 VM 8-1 S<br />
10 m3 VM 10-1 S VM 10-1 VM 10-1 B<br />
12 m3 VM 12-1 VM 12-1 B<br />
14 m3 VM 14-1 VM 14-1 B VM 14-2 SB VM 14-2 S<br />
16 m3 VM 16-2 SB VM 16-2 S<br />
18 m3 VM 18-2 SB VM 18-2 S<br />
20 m3 VM 20-2 SB VM 20-2 S<br />
22 m3 VM 22-2 VM 22-2 B<br />
27 m3 VM 27-2 VM 27-2 B<br />
30 m3 VM 30-2 VM 30-2 B<br />
32 m3 VM 32-3 B VM 32-3<br />
38 m3 VM 38-3 B VM 38-3<br />
45 m3 VM 45-3 B VM 45-3<br />
Elevator, 75 cm A A -<br />
Optional equipment<br />
- A A - - A<br />
Elevator, 220 cm - B B - A + B A + B B B A + B<br />
Elevator, 90/160 cm,<br />
for cross conveyor - - A A - - A A -<br />
Corner doors B - - B B - - - -<br />
A = To be mounted at the side B = To be mounted at the rear
C U S T O M E R P R O F I L E<br />
Fella implements give Taranaki contractor<br />
faultless performance<br />
Taranaki contractor Jason Holdem has a range <strong>of</strong> Fella mowers,<br />
tedders and swathers in his equipment fleet, and he says<br />
they are a critical part <strong>of</strong> his operation. Jason runs Holdem<br />
Contracting Limited from his home in Hawera, specialising in<br />
round and square hay and silage bales and direct drilling.<br />
He owns two Fella SM310 Trans mowers, which he’s<br />
had for the past seven years. “They’ve treated us well. The<br />
guys that operate them like operating them and they suit our<br />
system. Also parts availability is good – not that we throw too<br />
many parts at them,” Jason says.<br />
The SM310s operate at 3.1m wide and fold up for narrow<br />
transport width, making them easy to get in and out <strong>of</strong> farm<br />
gates. “They fold up well. They’ve got one wheel on the back<br />
for transport,” Jason says. “My two have probably done 2500-<br />
3000 hours each and in that time have only worn through a lot<br />
<strong>of</strong> skids. This winter they’ll get another tidy up in the workshop<br />
and will just keep going. They’re very robust and very seldom<br />
do we have to attack them with the welder.”<br />
Fella’s SM310 Trans mower features six cutting discs and<br />
1000 PTO. It has a semi-trailed steered rear wheel and central<br />
cutting height adjustment. Jason has owned a Fella Hydro 540<br />
tedder for three years. He says it is an easy-to-use tool that<br />
does a good job. “People do comment on the Fella tedder, and<br />
it’s good to know it does a good job,” he says. “It throws the<br />
crop out well and spreads it easily. It’s a good reliable tool and<br />
hasn’t given us any trouble. We just service and use it and it<br />
keeps going.”<br />
(From left): Stefan Sprock (Fella, Germany),<br />
Jason Holdem (Holdem Contracting) and Mark Sanger<br />
(Norwood Farm Machinery Centre, Hawera)<br />
The Fella Hydro 540 tedder has a working width <strong>of</strong> 5.5m,<br />
folding hydraulically to a transport width <strong>of</strong> 2.76m. It features<br />
four rotors, with six tines per rotor, and is semi mounted with<br />
three-point linkage. In addition, Holdem Contracting operates<br />
a 6.7m Fella 671 swather, and an 8m Fella 801 swather. “The<br />
671 is seven years old and was bought with one <strong>of</strong> the mowers,<br />
and the 801 is three years old,” Jason says.<br />
“They’re pretty similar machines and we haven’t had any<br />
major faults with them. They’re easy to use and we like the<br />
way they contour the ground. The smaller one is especially<br />
good on rough ground and follows the ground really well.”<br />
Jason says it is particularly easy to adjust the working width<br />
<strong>of</strong> the swathers. “They are a good basic machine and, like the<br />
mowers, they have treated us well and haven’t given us any<br />
problems.”
PRODUCT NEWS<br />
New Export Director visits New Zealand<br />
For several decades the name FELLA has been synonymous<br />
with quality and innovation in forage harvesting technology.<br />
Today their close customer contact allows them to constantly<br />
develop and perfect their machines allowing their dealers<br />
to <strong>of</strong>fer reliable expert technology including a wide range <strong>of</strong><br />
mowers, tedders and rakes to suit their pr<strong>of</strong>essional customer’s<br />
requirements.<br />
New Zealand importer C B Norwood Distributors Ltd<br />
recently hosted a visit by FELLA’s new Export Director,<br />
Mr Stefan Sprock who is set to play a significant role in the<br />
world wide expansion activities <strong>of</strong> the 92 year old FELLA<br />
company based in Feucht, Germany.<br />
Stefan originates from Oldenburger Munsterland and is<br />
able to look back on an impressive career. After training to be<br />
a mechanic on agricultural machinery, he completed a dual<br />
course in engineering before carrying out various product<br />
management roles within the agricultural industry.<br />
The visit reinforced the successful ten year partnership<br />
between FELLA and Norwood during which Stefan spent a<br />
week visiting customers and familiarising himself with the<br />
needs and specific requirements <strong>of</strong> the New Zealand market.<br />
In addition, Stefan stated that the use <strong>of</strong> New Zealand as<br />
a test and development market for new products such as the<br />
new 10 metre swather has been <strong>of</strong> considerable benefit and<br />
wishes to continue this highly effective test programme with<br />
new products in future.<br />
The share <strong>of</strong> turnover accounted for by exports from the<br />
specialists for fodder-harvest technology, who are based near<br />
Nuremberg in Germany, has now reached 75 percent. Last<br />
year, turnover totalled almost 60 million Euros.<br />
(From left): Stefan Sprock (Fella, Germany), Philip Reid, Jim Alpe, Markus Meyer and Rob Gawith (Colton Bros team)<br />
(From left):<br />
Stefan Sprock<br />
(Fella, Germany)<br />
and Peter Davies<br />
(Waikato dairy<br />
farmer)
C U S T O M E R P R O F I L E<br />
Vaderstad Carrier Drill<br />
fast, flexible and user friendly<br />
Wairarapa farmer John Petrie’s 3.0m Vaderstad Carrier<br />
trailed cultivator drill gives him the ability to carry out a range<br />
<strong>of</strong> cultivation jobs at quick speeds using just one machine.<br />
John and Lucy Petrie run 150 hectares, including a 27-hectare<br />
vineyard near Masterton, and another 100 hectares <strong>of</strong> mixed<br />
intensive cropping and fattening at Kahutara in the South<br />
Wairarapa.<br />
The Petries purchased their Vaderstad Carrier drill three<br />
years ago. It was the first <strong>of</strong> its type to be sold in New Zealand<br />
and the first Vaderstad drill they have owned. “My two blocks<br />
<strong>of</strong> land are 40 km apart, and because my operation is not vast,<br />
I wanted to have a multi-purpose machine,” John says.<br />
“Being minimum tillage means I can cultivate the ground<br />
straight from what was there before. Depending on the season<br />
and moisture, we can get away with one or two passes.” John<br />
wanted to eliminate unnecessary pieces <strong>of</strong> machinery that did<br />
not get a lot <strong>of</strong> use on the farm. “I figured having one good<br />
solid piece <strong>of</strong> equipment with a tractor to match it meant I<br />
wouldn’t have to go backwards and forwards with different<br />
pieces <strong>of</strong> equipment.” He says the Wairarapa is susceptible<br />
to changing weather patterns, which means it is <strong>of</strong>ten better<br />
to own your own machinery rather than be forced to wait for<br />
a contractor when conditions are good.<br />
“I used to have a direct drill but I moved away from it. A<br />
direct drill doesn’t work all the time for everything, and if I held<br />
onto it I would’ve had to double up. I was looking for equipment<br />
that I didn’t have to double up on,” John says.<br />
“No system is perfect and the first couple <strong>of</strong> years I was<br />
doing trials in different paddocks. But this Vaderstad drill has<br />
been pretty good. It’s very economical on the number <strong>of</strong> passes<br />
you have to do.” While late last year John was forced to do<br />
three passes due to bad weather conditions, he generally only<br />
does one pass for autumn stubble crops and two passes for<br />
renewing pasture. “It’s all about what moisture is in the ground<br />
and the depth that I put in. I try to do two or three inches.”<br />
The Vaderstad 3.0m Carrier drill is a flexible machine with<br />
stubble and furrow cultivation capabilities. It features a rubber<br />
roller to help consolidate without compaction. “It’s very useful<br />
for me with my operation. This year I’ve only put in about 80<br />
acres and it doesn’t take any time at all. I can do between six<br />
and eight acres an hour, travelling at about 11 kph.”<br />
Though some initial modifications were made to the Petries’<br />
machine to alter the fixed stay bar, they’ve had few problems<br />
with it since. “We had to recalibrate the seed rollers after the<br />
first season because it became noticeable after doing three or<br />
four different seeds that it was on the wrong setting. Once we<br />
did that it was all go,” John says.<br />
“I find it very easy to use and very user friendly. I pull it with<br />
a 135 hp New Holland TVT tractor. It’s quite a heavy piece <strong>of</strong><br />
equipment and if the ground is fairly heavy you’ve got to have<br />
a wee bit <strong>of</strong> grunt.”<br />
Interesting Fact – Planting Maize<br />
The diversity <strong>of</strong> the machine was very clearly demonstrated<br />
when John used the Carrier Drill to establish a crop <strong>of</strong><br />
maize. The establishment was superb and the crop could<br />
have, to all intents and purposes been established with a<br />
precision planter. Of course plant spacing in the row could<br />
not be accurately maintained, however for small one-<strong>of</strong>f<br />
applications such as this the considerable flexibility <strong>of</strong> the<br />
machine is ideal. John yielded 7 tonnes per hectare <strong>of</strong><br />
maize from this planting.
F O C U S O N P A R T S & S E R V I C E<br />
Why choose ‘Genuine’ parts?<br />
You should choose ‘Genuine’ parts for the following reasons:<br />
• Product<br />
• Precise fit<br />
• Performance<br />
• Price and overall economy<br />
Product<br />
• Using advanced 3D-CAD design tools with simulation<br />
support to develop outstanding products.<br />
• High class industrial manufacturing including laser cutting,<br />
CNC-machining, hardening and tempering technology, all in<br />
a quality controlled process.<br />
• The use <strong>of</strong> high grade Swedish steel.<br />
• Unique materials such as V-55 steel for discs.<br />
Precise fit<br />
• By using Genuine parts you know you are<br />
guaranteed that the parts fit and work as<br />
they should.<br />
• To service your machine and change parts<br />
becomes simple and problem free, the way<br />
it should be.<br />
As the parts fit perfectly you can also use<br />
your machine as you have planned and when<br />
it suits you.<br />
One example <strong>of</strong> how important it is to have<br />
a precise fit is the disc hub/ball bearing/disc<br />
relationship, where the extremely precise press-out <strong>of</strong> the disc<br />
interlocks the ball bearing in the hub. Using non-genuine parts,<br />
for example a disc, can in this case cause breakdowns with<br />
costly effects <strong>of</strong> having to change other parts, in addition to<br />
annoying down-time.<br />
Performance<br />
• Only by using Genuine parts<br />
can you be sure that your<br />
machine really performs to its<br />
full potential.<br />
• When it comes to performance,<br />
highest possible seeding<br />
precision is a good example…<br />
Who does not want good<br />
emergence and highest possible yield?<br />
• Both when it comes to performance by means <strong>of</strong> reliable<br />
function as well as maximised wear resistance, Genuine<br />
parts are the right choice<br />
Price and overall economy<br />
• Compare the price on Genuine parts and the alternatives; it’s<br />
a myth that Genuine are always more expensive! Remember<br />
it’s the cost per hectare that counts not the initial price <strong>of</strong><br />
the parts.<br />
• The value <strong>of</strong> high seeding precision, good emergence and<br />
highest possible yield is even more important than ever!<br />
• Genuine parts or not has a big impact on the valuation <strong>of</strong><br />
your machine at trade-in or second-hand sale.<br />
“Genuine” parts – Long-term the cheapest?<br />
Genuine Parts are the cheapest! Yes, it might sound surprising since<br />
original parts are <strong>of</strong>ten associated with high prices, even though<br />
the high quality isn’t to be questioned and honestly speaking, we<br />
usually do not like to brag about being “cheap”… after all, the word<br />
“cheap” can be interpreted in many different ways.<br />
We think it’s time to re-evaluate the meaning <strong>of</strong> “cheap” when<br />
it comes to spare parts. Genuine parts are the cheapest, taking<br />
into account the full value. It means in effect that choosing<br />
them for the maintenance <strong>of</strong> your highly valued investment is<br />
a choice that long-term is the cheapest!<br />
The full value <strong>of</strong> choosing Genuine parts is getting:<br />
Highest possible performance and wear resistance<br />
• It is NOT cheap to have breakdowns and standing still<br />
causing loss <strong>of</strong> valuable work time in the middle <strong>of</strong> the<br />
intensive high season.<br />
• It is NOT cheap having to change wear parts more <strong>of</strong>ten<br />
because <strong>of</strong> a shorter lifespan.<br />
Best possible economy and pr<strong>of</strong>itability<br />
• It is NOT cheap to have even the slightest loss <strong>of</strong> yield due<br />
to a slightly poorer seed placement or emergence.<br />
Best second-hand value<br />
• It is NOT cheap to have your machine de-valued because<br />
<strong>of</strong> having fitted non-genuine parts when it’s time to sell or<br />
trade it in for a new one.<br />
Choose Genuine parts – it will make you happy!<br />
We also believe that the success <strong>of</strong> next season starts<br />
with what action you take in your <strong>of</strong>f-season servicing.<br />
So, to help you with your parts requirements, we are<br />
pleased to <strong>of</strong>fer our 2010 <strong>of</strong>f-season indent order. Your<br />
local dealer is waiting for your call, or they will contact<br />
you over the next few weeks to discuss this programme.<br />
Don’t wait, phone us today!!
POWER HARROWS, MULCHERS & ROTARY HOES<br />
www.breviglieri.co.nz<br />
PRECISION FINGER & VACUUM METERING ® PLANTERS<br />
www.kinze.co.nz ®<br />
MOWERS, CONDITIONERS, RAKES & TEDDERS<br />
www.fella.co.nz<br />
PLOUGHS, POWER HARROWS, CULTIVATORS & DRILLS<br />
www.lemken.co.nz<br />
FRONT END LOADERS, FRONT LINKAGES & ATTACHMENTS<br />
www.m-x.co.nz<br />
MIxER/FEEDER WAGONS & FORAGE HARVESTERS<br />
www.jfstoll.co.nz<br />
BALE WRAPPERS & FORAGE CONSERVATION<br />
www.tanco.co.nz<br />
TRAILED & MOUNTED FERTILISER SPREADERS<br />
CULTIVATORS, ROLLERS & SEEDING EQUIPMENT<br />
www.vaderstad.co.nz<br />
PRECISION APPLICATORS & SEEDERS<br />
www.stocksag.co.nz<br />
DISC HARROWS & CULTIVATORS<br />
www.baldan.co.nz<br />
If you would like<br />
more information<br />
on any <strong>of</strong> the<br />
products featured<br />
in this newsletter<br />
please contact<br />
your local specialist<br />
equipment dealer.<br />
®<br />
®<br />
And, finally...<br />
To keep you up-to-date with trends around<br />
the world we have invited our suppliers<br />
to comment on the market in their own<br />
country. This issue we hear from Tim<br />
Needham <strong>of</strong> Vaderstad in Australia.<br />
The future <strong>of</strong> farming is bright<br />
in the long term<br />
The world agricultural market has just been<br />
through one <strong>of</strong> the biggest fluctuations that<br />
it has seen for years. The rapid succession<br />
<strong>of</strong> two major crises – the global food crisis<br />
and the subsequent financial crisis and<br />
economic recession – has delivered the<br />
hardest blow to world food security in<br />
decades.<br />
In the long term, however, world<br />
agriculture is going to be under extreme<br />
pressure to dramatically increase<br />
productivity.<br />
World population is predicted to grow<br />
from nearly 7 billion now to approximately<br />
9 billion by 2050, a growth <strong>of</strong> almost 30%.<br />
People in less developed countries are now<br />
expecting a better standard <strong>of</strong> living, their<br />
economies are developing and they are<br />
eating more and better food.<br />
Average life expectancy is increasing<br />
with better medicines and improved living<br />
conditions. In 1950 the average was 68,<br />
today it is 77 years.<br />
There is a reduction in the area <strong>of</strong> land<br />
in production as more roads and buildings<br />
are constructed. There is a huge shift<br />
<strong>of</strong> land use from food production to fuel<br />
production. 50% <strong>of</strong> gasoline used in Brazil<br />
is Bio Ethanol. In 1990 approx. 5% <strong>of</strong> US<br />
maize production was for bi<strong>of</strong>uel, now it’s<br />
over 40%.<br />
According to the FAO, food production<br />
is going to have to increase by 50% in the<br />
next 30 years to keep up with these factors.<br />
Obviously there are huge areas <strong>of</strong> land in<br />
the former Eastern Block that are still not<br />
cropped and can come into production.<br />
Nevertheless there is going to be a<br />
significant requirement to increase yields,<br />
and every square metre <strong>of</strong> productive land<br />
will need to be farmed.<br />
At Vaderstad we see an increased<br />
demand for wider and faster machines,<br />
600 hp tractors are coming. We continue<br />
to invest heavily into the ‘state <strong>of</strong> the art’<br />
manufacturing techniques at our factory<br />
in Sweden, and almost 8% <strong>of</strong> turnover is<br />
spent on Research and Development. A<br />
new 3D laser cutting hall and 2,000 tonne<br />
fully automated steel storage facility was<br />
completed last November which allows<br />
us to cut tube by robot laser at any angle<br />
and any shape, simplifying welding jigs and<br />
assembly. An additional 5,000 sq metres <strong>of</strong><br />
factory will be built this Autumn at our Seed<br />
Hawk factory in Canada. This second phase<br />
<strong>of</strong> development will triple the production<br />
capacity for our no-till Seed Hawk air<br />
seeders.<br />
Your local dealers:<br />
Kaikohe Dave Boyt Farm Machinery Centre (09) 405-2269<br />
Whangarei Dave Boyt Farm Machinery Centre (09) 438-4719<br />
Pukekohe Norwood Farm Machinery Centre (09) 238-7189<br />
Ngatea Central Motors (2001) Ltd (07) 867-7524<br />
Morrinsville Norwood Farm Machinery Centre (07) 889-8505<br />
Te Awamutu Norwood Farm Machinery Centre (07) 872-0232<br />
Matamata Murray Wilcox Ltd (07) 888-7139<br />
Putaruru Putaruru Tractor Services (07) 883-7544<br />
Bay <strong>of</strong> Plenty R & R Tractors (Te Puke) (07) 573-9107<br />
Rotorua PSL Agri (07) 343-6081<br />
Taupo PSL Agri (07) 378-2673<br />
Hastings/Gisborne Norwood Farm Machinery Centre (06) 873-7300<br />
New Plymouth Norwood Farm Machinery Centre (06) 757-5582<br />
Hawera Norwood Farm Machinery Centre (06) 278-6159<br />
Palmerston North Norwood Farm Machinery Centre (06) 351-2799<br />
Masterton Norwood Farm Machinery Centre (06) 377-3184<br />
Blenheim Williams Service Centre (1990) Ltd (03) 578-1021<br />
Nelson N S Rogers Ltd (03) 528-9212<br />
Westport Westland Farmers (03) 788-8050<br />
Christchurch Norwood Farm Machinery Centre (03) 349-5089<br />
Ashburton Gluyas Motors (03) 307-5800<br />
Timaru Johnson Gluyas Tractors Ltd (03) 688-1133<br />
Mosgiel Norwood Farm Machinery Centre (03) 489-7754<br />
Southland Thompson Machinery Ltd (03) 208-9179<br />
Do you have a story or something <strong>of</strong> interest to share?<br />
If so, please contact us at: Implementation, C B Norwood Distributors Ltd, Freepost 255, PO Box 1265, Palmerston North<br />
Phone (0800) 667-9663, Fax (06) 356 4939