Instruction Sheet: Torcia In-Ground Light - American Lighting

TORCIA IN-GROUND LIGHT
Installation instructions for TG1-12V-WW-SS
READ ALL OF THESE INSTALLATION INSTRUCTIONS BEFORE INSTALLING THE FIXTURE. FAILURE TO
FOLLOW INSTALLATION INSTRUCTIONS AND ALL APPLICABLE ELECTRICAL CODES WILL VOID THE
PRODUCT WARRANTY.
WARNING:
These products may represent a possible shock or fire hazard if improperly installed or attached in any
way. Products should be installed in accordance with these instructions, current electrical codes and/or
the current National Electric Code (NEC).
WARNING:
Disconnect supply power from the source prior to installation. This product must be installed by a
person familiar with the construction and operation of the product and the hazards involved, and in
accordance with current electrical codes and/or the current National Electric Code (NEC) for two wire
installation. Consult a local licensed electrician if you are not sure about the installation.
APPLICATION / USE:
This product is designed for recessed mounting only. Appropriate installations include mounting into a
concrete slab or retaining wall using the black PVC sleeve included with the fixture; into the earth using the
black PVC sleeve included; or into an interior or exterior wall with or without the black PVC sleeve. For any
outdoor or other wet location installation where the PVC sleeve is used vertically, the PVC sleeve must have proper
drainage to avoid immersion in water! The Torcia In-Ground Light may come into contact with water, but may
not be immersed in water.
LAYOUT AND SELECTION OF RECOMMENDED CONSTANT VOLTAGE DRIVER
The Torcia In-Ground Light (1.4W each) requires a regulated 12V driver with a DC output.
American Lighting recommends the following drivers as a function of how many fixtures are attached:
Quantity LED-DR-12 LED-DR60-12 LED-DR100-12
(1-25 watts) (1-60 watts) (1-100 watts)
1-17
18-42
43-71
NOTE: FOR OUTDOOR INSTALLATIONS THE CONSTANT VOLTAGE DRIVER MUST BE ENCLOSED IN A WATER-
PROOF ENCLOSURE. All conductors and power connections must be installed per current state and local
electrical codes. Drivers must be mounted properly inside enclosure and also must have clearance above
and around for proper heat dissipation.
IN-GROUND / SOIL INSTALLATION:
Note: Debris must be kept away from the lens to allow proper operation and optimize light output. Inspect
the installed fixture periodically to ensure that the lens is kept clean and free of dirt, dust, plants, leaves and
any other kind of obstruction. Adhering to a regular maintenance schedule is advised.
Torcia Lights have certain other installation requirements and considerations:
1. Provide proper drainage for PVC sleeve so that fixtures will not be immersed in water (see also next page).
2. Do not locate fixtures in low areas where water will collect.
3. Make sure trim is flush to 1/8” above finish grade to prevent water from accumulating on lens.
4. In turf applications, it is recommended to keep grass away from fixture using borders or concrete or some
kind of landscape material so that lawn equipment will not damage the fixture or its installation.
www.americanlighting.com
©2012 American Lighting
Denver, CO 80231 Made in China

TORCIA IN-GROUND LIGHT
Installation instructions for TG1-12V-WW-SS (continued)
IN-GROUND / SOIL INSTALLATION: (continued from page 1)
Be sure power to the junction box has been shut off at the main.
1. Determine location of fixtures in relation to each other and to the power supply. Note: Larger distances
from the power supply will create loss of initial voltage (voltage drop). If voltage drop becomes too large,
the light output will be noticeably less. In order to keep voltage drop from affecting light output, keep
fixtures within 35 feet of the power supply and use 16-gauge wire or larger (see also part 4 below).
2. For each fixture location, dig approximately 9” diameter hole, 10” deep.
3. Add 4-6” drainage material (such as pea gravel and/or sand) in each hole.
4. Push fixture barrel into PVC sleeve. Rubber gasket must be a tight fit. It will require pressure to seat fully.
5. Using 2-conductor wire rated for direct burial applications, wire each fixture to the power supply in a
parallel wiring configuration (homerun back to the power supply).
6. Make secure wire connections using UL Listed direct burial wire nuts (not included), matching polarity:
brown wire is positive (+), blue wire is negative (-). Note: In order for the Torcia fixture to light, the wiring
must have proper polarity in relation to the power supply’s output. If reversed, this will not damage the
fixture or the LED, it simply will not illuminate until polarity is correct and connections are solid.
7. Test light by connecting lead wire to power supply and restoring power at the main.
8. Coil any extra lead wire below the fixture/PVC sleeve.
8. Backfill hole with pea gravel or sand.
9. Repeat with additional fixtures.
CONCRETE POUR INSTALLATION:
Be sure power to the junction box has been shut off at the main.
1. Repeat steps 1-3 above except hole should be 6” deep.
2. Run rigid conduit to each location and pull 2-conductor wire, 16-gauge or larger leaving 18” extra
wire length at each fixture location.
3. Using standard masonry techniques , anchor and plug each PVC sleeve in upright position at slab
finish height. Be sure to pull extra length wire up through each PVC sleeve.
4. Add drainage material around the PVC sleeve to grade height.
5. After slab has been poured and is set, follow steps 4-7 above, but test each fixture BEFORE seating it
into PVC sleeve.
6. Coil extra lead into sleeve (cut back extra if wire will not fit).
7. Repeat with additional fixtures.
ADDITIONAL SAFETY MEASURES:
1. LEDs are not serviceable. Do not attempt to open the LED light engine.
2. LEDs are bright. Do not look directly into fixture.
3. Not intended for surface mounting in any type of installation.
4. Do not alter fixture.
www.americanlighting.com
©2012 American Lighting
Denver, CO 80231 Made in China