MIDLAND 8001XT Januar 2012 MODIFICATIONS TO ... - Thiecom
MIDLAND 8001XT Januar 2012 MODIFICATIONS TO ... - Thiecom
MIDLAND 8001XT Januar 2012 MODIFICATIONS TO ... - Thiecom
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
<strong>MIDLAND</strong> <strong>8001XT</strong> <strong>Januar</strong> <strong>2012</strong><br />
<strong>MODIFICATIONS</strong> <strong>TO</strong> CHANNELS EXPANSION,<br />
ENABLE +10 KHz AND RF POWER OUTPUT INCREASE<br />
Modifikationen zur Kanalerweiterung, + 10 kHz Zwischenkanäle<br />
und Leistungserhöhung<br />
CHANNELS EXPANSION AND +10 KHz FUNCTION<br />
Kanalerweiterung<br />
Important Note:<br />
All described modifications are only allowed, if the modified radio will be used by licensed<br />
radio amateurs according to the applicable amateur radio regulations. It is not allowed to<br />
use a modified radio within EU / R&TTE countries for any CB radio purpose. Every user is<br />
responsible to use his radio according to the regulations, which apply for the purpose of<br />
use.<br />
Wichtiger Hinweis: Alle beschriebenen Einstellungen sind nur zulässig, wenn das<br />
modifizierte Gerät von einem lizenzierten Funkamateur im Rahmen seiner<br />
Lizenzbestimmungen auf Amateurfunkfrequenzen betrieben wird. Im Rahmen des CB Funks<br />
darf ein modifiziertes Gerät nicht benutzt werden. Jeder Benutzer ist selbst dafür<br />
verantwortlich, wenn er mit für ihn nicht zulässigen Einstellungen angetroffen wird.<br />
-Turn off the radio and remove the power supply cable;<br />
-Open the unit, unscrew 5 screw and remove lower cover (cover on speaker side);<br />
-Locate the area of the radio where the modification will be done (see picture);<br />
- Gerät ausschalten, Power Kabel unterbrechen, Gerät öffnen (Lautsprecherseite)<br />
- Die im Bild markierte Stelle zeigt die Steckbrücke<br />
-Move on the left the jumper (PAD605) as shown in the below picture:<br />
Steckbrücke nach Bild einstellen.
With this modification the radio will work on 400 channels in 10 bands, from 25.615 MHz<br />
to 30.105 MHz; the display will show the bands from A 01 (lower frequency) to L 40<br />
(higher frequency).<br />
This modification enables the +10 KHz function as well; to activate +10 KHz function press<br />
the key shows in the below picture:<br />
Nach dieser Modifikation arbeitet das Gerät im 400 Kanalbetrieb mit den Bandanzeigen A<br />
01 bis L 40. Gleichzeitig aktiviert ist die + 10 kHz Funktion, die man auf Knopfdruck<br />
erreicht:
-RF POWER OUTPUT EXPANSION<br />
HF Leistungserhöhung<br />
-Locate the area of the radio where the modification will be done (see the circle in the<br />
below picture); Der Bereich auf der Platine, wo die dazu nötigen Brücken sich befinden,<br />
ist hier markiert:<br />
-move the jumpers shown in the below picture in this way: Steckbrücken einstellen<br />
-P106 OPEN - OFFEN;<br />
-P119 OPEN - OFFEN;<br />
-P104 CLOSE- Geschlossen.
It is possible to increase further the RF power (but also the TX distortion will increase) in<br />
this way: -turn the trimmers shows in the below picture;<br />
Man kann auch mit den Trimmpotis die Leistung einstellen (dabei erhöhen sich aber die<br />
Verzerrungen):<br />
-VR415 turn clockwise - auf Rechtsanschlag;<br />
-VR414 turn clockwise - auf Rechtsanschlag<br />
-VR105 turn anticlockwise - auf Linksanschlag<br />
With these modifications the RF power output will be up to 20 Watt PEP (AM, FM and<br />
SSB).<br />
Mit diesen Modifikationen kann man Leistungswerte bis zu 20 Watt PEP (AM, FM, SSB)<br />
erreichen.
Mo odulationn<br />
Adjustments<br />
– Modulatiionseinst<br />
tellungen n<br />
To o increase the modulation<br />
degree<br />
in AMM<br />
and FM deviation d the t trimmer potentiometers can<br />
be e found here:<br />
VR R203 (AM mod degree)<br />
VR R303 (FM peak deviaation)<br />
VR R203:<br />
VR R303: