Prisma Plus PH System - Schneider Electric

More documents

Recommendations

Info

DD384407 DD384408 Distribution Catalogue numbers 06545. 06543. DD383356 DD384441 Form 2 partitioning Partitioning of lateral vertical busbars Lateral partitioning b b b v v b Vertical barrier made of insulating slats. Can be installed on both sides of Linergy and flat busbars. Made up of: five extruded slats that clip to the supports two metal plates at the top and bottom that can be cut out to pass a PE or PEN. The space between the slats is sufficient for prefabricated connections (one copper bar, 5 or 10 mm thick, or insulated flexible bars) or for cables up to 35 mm², while maintaining the degree of protection IP2X compliance with standard IEC 60695.2.1 concerning withstand to fire. Form 2 restoration for side-barrier cut-out This kit enables passage of the connection between a device > 1600 A (NW, INS) and lateral vertical busbars. It is made up of an insulated plate (six modules H 300 mm) that can be cut as required, supplied with supports and the necessary hardware. It can be installed at any height in the switchboard. Cat. no. selection Designation Cat. no. Form 2 side barrier for D 500 mm cubicle 06545 Form 2 restoration kit 04924 Partitioning extension For the <strong>PH</strong> system switchboards 800 mm depth (500 + 300), a partitioning extension for 300 mm depth is required. Designation Cat. no. Partitioning extension in 800 mm depth 06543 401F_E22905.indd version: 1.0 - 06/2010 3
DD384409 DD384410 Distribution Catalogue numbers 06540. 06555. 4 DD383360 DD383362 Form 2 partitioning Front and rear barrier Barrier, W 300 mm, from top to bottom of the cubicle. Can be installed in the front and rear of the busbar compartment. Protects against direct contact with the busbars. Front protection Is realized by the association of the door W 300 mm and this barrier. Metallic barrier, composed of 2 parts H 850mm, pre-cut at both ends. Rear protection A barrier is required at the rear of the busbar compartment in cubicles that are 800, 1000 and 1300 mm deep. Cat. no. selection Designation Cat. no. Front or rear barrier for lateral vertical busbars W 300 mm 06540 Inter-cubicle partitioning Metal partition, used to separate two adjacent cubicles. It is made up of two panels, each 850 mm high. The top and bottom ends have knock-outs for horizontal busbars. Supplied with the necessary supports and hardware, the partition is mounted on the framework and does not hinder installation of the functional mounting plates Cat. no. selection Designation Cat. no. Inter-cubicle partitioning D 500 mm 06555 D 800 mm 04911 + 06543 version: 1.0 - 06/2010 401F_E22905.indd
Page 1 and 2: Low Voltage electrical distribution
Page 3 and 4: Index Index Index Cat. no. Designat
Page 5 and 6: PD391265b_SE PD391266b_SE PD391267b
Page 7 and 8: General presentation Presentation 4
Page 9 and 10: DD384395 Functional units Catalogue
Page 11 and 12: DD384396 Distribution Catalogue num
Page 13 and 14: PD391273b_SE Distribution Catalogue
Page 15 and 16: DD384402 DD384403 Distribution Cata
Page 19: Distribution Catalogue numbers 2 PD
Page 25 and 26: DD384415 DD384416 Enclosures Catalo
Page 27 and 28: DD384423 DD384424 DD384425 Enclosur
Page 29 and 30: DD384440 Enclosures Catalogue numbe
Page 31 and 32: Dimensions Dimensions 2 DD384433 DD
Page 33: Schneider Electric Industries SAS 3

Prisma Plus PH System - Schneider Electric

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?