Corrigendum - REACH24H Consulting Group
Corrigendum - REACH24H Consulting Group Corrigendum - REACH24H Consulting Group
6.5.1.3 Categories of IBCs 6.5.1.3.1 Metal IBCs consist of a metal body together with appropriate service and structural equipment. 6.5.1.3.2 Flexible IBCs consist of a body constituted of film, woven fabric or any other flexible material or combinations thereof, and if necessary an inner coating or liner, together with any appropriate service equipment and handling devices. 6.5.1.3.3 Rigid plastics IBCs consist of a rigid plastics body, which may have structural equipment together with appropriate service equipment. 6.5.1.3.4 Composite IBCs consist of structural equipment in the form of a rigid outer casing enclosing a plastics inner receptacle together with any service or other structural equipment. They are so constructed that the inner receptacle and outer casing once assembled, form and are used as, an integrated single unit to be filled, stored, transported or emptied as such. 6.5.1.3.5 Fibreboard IBCs consist of a fibreboard body with or without separate top and bottom caps, if necessary an inner liner (but no inner packagings), appropriate service and structural equipment. 6.5.1.3.6 Wooden IBCs consist of a rigid or collapsible wooden body together with an inner liner (but no inner packagings) and appropriate service and structural equipment. 6.5.1.4 Designatory code system for IBCs 6.5.1.4.1 The code shall consist of two Arabic numerals as specified in (a); followed by a capital letter(s) specified in (b); followed, when specified in an individual section, by an Arabic numeral indicating the category of IBC. (a) Copyright@United Nations, 2011. All rights reserved. Type Rigid Flexible (b) Materials For solids filled or discharged by gravity under pressure of more than 10 kPa (0.1 bar) 11 21 13 - A. Steel (all types and surface treatments) B. Aluminium C. Natural wood D. Plywood F. Reconstituted wood G. Fibreboard H. Plastics material L. Textile M. Paper, multiwall N. Metal (other than steel or aluminium). - 256 - For liquids 6.5.1.4.2 For composite IBCs, two capital letters in Latin characters shall be used in sequence in the second position of the code. The first shall indicate the material of the inner receptacle of the IBC and the second that of the outer packaging of the IBC. 31 -
Copyright@United Nations, 2011. All rights reserved. 6.5.1.4.3 The following types and codes of IBC are assigned: Material Category Code Paragraph Metal 6.5.5.1 A. Steel for solids, filled or discharged by gravity 11A for solids, filled or discharged under pressure 21A for liquids 31A B. Aluminium for solids, filled or discharged by gravity 11B for solids, filled or discharged under pressure 21B for liquids 31B N. Other than steel for solids, filled or discharged by gravity 11N or aluminium for solids, filled or discharged under pressure 21N for liquids 31N Flexible 6.5.5.2 H. Plastics woven plastics without coating or liner 13H1 woven plastics, coated 13H2 woven plastics with liner 13H3 woven plastics, coated and with liner 13H4 plastics film 13H5 L. Textile without coating or liner 13L1 coated 13L2 with liner 13L3 coated and with liner 13L4 M. Paper multiwall 13M1 multiwall, water resistant 13M2 H. Rigid Plastics for solids, filled or discharged by gravity, fitted with structural equipment 11H1 6.5.5.3 for solids, filled or discharged by gravity, freestanding 11H2 for solids, filled or discharged under pressure, fitted with structural equipment 21H1 for solids, filled or discharged under pressure, freestanding 21H2 for liquids, fitted with structural equipment 31H1 for liquids, freestanding 31H2 HZ. Composite with plastic inner for solids, filled or discharged by gravity, with rigid plastics inner receptacle 11HZ1 receptacle for solids, filled or discharged by gravity, with flexible plastics inner receptacle 11HZ2 for solids, filled or discharged under pressure, with rigid plastics inner receptacle 21HZ1 for solids, filled or discharged under pressure, with flexible plastics inner receptacle 21HZ2 for liquids, with rigid plastics inner receptacle 31HZ1 a 6.5.5.4 for liquids, with flexible plastics inner receptacle 31HZ2 a The code shall be completed by replacing the letter Z with a capital letter in accordance with 6.5.1.4.1 (b) to indicate the nature of the material used for the outer casing. Cont'd on next page - 257 -
- Page 665 and 666: 6.2.2.4 Periodic inspection and tes
- Page 667 and 668: 6.2.2.5.3 Manufacturer's quality sy
- Page 669 and 670: 6.2.2.5.4.8 The application shall i
- Page 671 and 672: pressure receptacle is not the comp
- Page 673 and 674: (d) The designation of the pressure
- Page 675 and 676: Copyright@United Nations, 2011. All
- Page 677 and 678: Copyright@United Nations, 2011. All
- Page 679 and 680: 6.2.3.4 Marking shall be in accorda
- Page 681 and 682: Copyright@United Nations, 2011. All
- Page 683 and 684: CHAPTER 6.3 REQUIREMENTS FOR THE CO
- Page 685 and 686: Copyright@United Nations, 2011. All
- Page 687 and 688: (d) flat on the shortest side; (e)
- Page 689 and 690: CHAPTER 6.4 REQUIREMENTS FOR THE CO
- Page 691 and 692: Copyright@United Nations, 2011. All
- Page 693 and 694: 6.4.7.9 If the containment system f
- Page 695 and 696: Copyright@United Nations, 2011. All
- Page 697 and 698: Copyright@United Nations, 2011. All
- Page 699 and 700: Copyright@United Nations, 2011. All
- Page 701 and 702: Copyright@United Nations, 2011. All
- Page 703 and 704: 6.4.18 Enhanced water immersion tes
- Page 705 and 706: Copyright@United Nations, 2011. All
- Page 707 and 708: Copyright@United Nations, 2011. All
- Page 709 and 710: Copyright@United Nations, 2011. All
- Page 711 and 712: Copyright@United Nations, 2011. All
- Page 713 and 714: Copyright@United Nations, 2011. All
- Page 715: CHAPTER 6.5 REQUIREMENTS FOR THE CO
- Page 719 and 720: Marking shall be applied in the seq
- Page 721 and 722: 6.5.2.4 Marking of remanufactured c
- Page 723 and 724: 6.5.4.4.3 A report of each inspecti
- Page 725 and 726: Copyright@United Nations, 2011. All
- Page 727 and 728: Copyright@United Nations, 2011. All
- Page 729 and 730: Copyright@United Nations, 2011. All
- Page 731 and 732: 6.5.6.3 Preparation of IBCs for tes
- Page 733 and 734: 6.5.6.5.5 Criteria for passing the
- Page 735 and 736: (b) For IBCs of types 31H1, 31H2, 3
- Page 737 and 738: 6.5.6.10 Tear test 6.5.6.10.1 Appli
- Page 739 and 740: 6.5.6.14 Test report Copyright@Unit
- Page 741 and 742: 6.6.1 General Copyright@United Nati
- Page 743 and 744: 6.6.3.2 Examples of the marking 50
- Page 745 and 746: Copyright@United Nations, 2011. All
- Page 747 and 748: 6.6.5.2.2 In the drop tests for liq
- Page 749 and 750: 6.6.5.3.4 Drop test 6.6.5.3.4.1 App
- Page 751 and 752: CHAPTER 6.7 REQUIREMENTS FOR THE DE
- Page 753 and 754: Copyright@United Nations, 2011. All
- Page 755 and 756: 6.7.2.2.14 The values of yield stre
- Page 757 and 758: 6.7.2.4.7 When in the applicable po
- Page 759 and 760: (b) A liquid tight closure at the e
- Page 761 and 762: 6.7.2.12.2 The combined delivery ca
- Page 763 and 764: 6.7.2.12.2.3 Minimum required rate
- Page 765 and 766: 6.7.2.17.5 When portable tanks are
Copyright@United Nations, 2011. All rights reserved.<br />
6.5.1.4.3 The following types and codes of IBC are assigned:<br />
Material Category Code Paragraph<br />
Metal<br />
6.5.5.1<br />
A. Steel<br />
for solids, filled or discharged by gravity 11A<br />
for solids, filled or discharged under pressure 21A<br />
for liquids 31A<br />
B. Aluminium for solids, filled or discharged by gravity 11B<br />
for solids, filled or discharged under pressure 21B<br />
for liquids 31B<br />
N. Other than steel for solids, filled or discharged by gravity 11N<br />
or aluminium for solids, filled or discharged under pressure 21N<br />
for liquids 31N<br />
Flexible<br />
6.5.5.2<br />
H. Plastics woven plastics without coating or liner 13H1<br />
woven plastics, coated 13H2<br />
woven plastics with liner 13H3<br />
woven plastics, coated and with liner 13H4<br />
plastics film 13H5<br />
L. Textile without coating or liner 13L1<br />
coated 13L2<br />
with liner 13L3<br />
coated and with liner 13L4<br />
M. Paper<br />
multiwall 13M1<br />
multiwall, water resistant 13M2<br />
H. Rigid Plastics for solids, filled or discharged by gravity,<br />
fitted with structural equipment<br />
11H1<br />
6.5.5.3<br />
for solids, filled or discharged by gravity, freestanding 11H2<br />
for solids, filled or discharged under pressure,<br />
fitted with structural equipment<br />
21H1<br />
for solids, filled or discharged under pressure,<br />
freestanding<br />
21H2<br />
for liquids, fitted with structural equipment<br />
31H1<br />
for liquids, freestanding<br />
31H2<br />
HZ. Composite with<br />
plastic inner<br />
for solids, filled or discharged by gravity,<br />
with rigid plastics inner receptacle<br />
11HZ1<br />
receptacle for solids, filled or discharged by gravity,<br />
with flexible plastics inner receptacle<br />
11HZ2<br />
for solids, filled or discharged under<br />
pressure, with rigid plastics inner receptacle<br />
21HZ1<br />
for solids, filled or discharged under<br />
pressure, with flexible plastics inner receptacle<br />
21HZ2<br />
for liquids, with rigid plastics inner receptacle 31HZ1<br />
a<br />
6.5.5.4<br />
for liquids, with flexible plastics inner receptacle 31HZ2<br />
a<br />
The code shall be completed by replacing the letter Z with a capital letter in accordance<br />
with 6.5.1.4.1 (b) to indicate the nature of the material used for the outer casing.<br />
Cont'd on next page<br />
- 257 -