Corrigendum - REACH24H Consulting Group

Recommendations

Info

Copyright@United Nations, 2011. All rights reserved. Test pressure means the required pressure applied during a pressure test for qualification or requalification; Through or into means through or into the countries in which a consignment is transported but specifically excludes countries “over” which a consignment is carried by air, provided that there are no scheduled stops in those countries; Transport index (TI) assigned to a package, overpack or freight container, or to unpackaged LSA-I or SCO-I, for the transport of Class 7 material, means a number which is used to provide control over radiation exposure; Tube means a seamless transportable pressure receptacle of a water capacity exceeding 150 litres but not more than 3 000 litres; UNECE means the United Nations Economic Commission for Europe (UNECE, Palais des Nations, 8-14 avenue de la Paix, CH-1211 Geneva 10, Switzerland); Vehicle means a road vehicle (including an articulated vehicle, i.e. a tractor and semi-trailer combination), railroad car or railway wagon. Each trailer shall be considered as a separate vehicle; Vessel means any seagoing vessel or inland waterway craft used for carrying cargo; Wooden barrel means a packaging made of natural wood, of round cross-section, having convex walls, consisting of staves and heads and fitted with hoops; Working pressure means the settled pressure of a compressed gas at a reference temperature of 15 °C in a full pressure receptacle; - 32 -
Clarifying examples for certain defined terms The following explanations and examples are meant to assist in clarifying the use of the some of the packaging terms defined in this section. The definitions in this section are consistent with the use of the defined terms throughout the Regulations. However, some of the defined terms are commonly used in other ways. This is particularly evident in respect of the term “inner receptacle” which has often been used to describe the “inners” of a combination packaging. The “inners” of “combination packagings” are always termed “inner packagings” not “inner receptacles”. A glass bottle is an example of such an “inner packaging”. The “inners” of “composite packagings” are normally termed “inner receptacles”. For example, the “inner” of a 6HA1 composite packaging (plastics material) is such an “inner receptacle” since it is normally not designed to perform a containment function without its “outer packaging” and is not therefore an “inner packaging”. 1.2.2 Units of measurement Copyright@United Nations, 2011. All rights reserved. 1.2.2.1 The following units of measurement a are applicable in these Regulations: Measurement of SI Unit b Acceptable alternative unit - 33 - Relationship between units Length m (metre) -- -- Area m 2 (square metre) -- -- Volume m 3 (cubic metre) 1 c (litre) 1 l = 10 -3 m 3 Time s (second) min (minute) 1 min = 60 s h (hour) 1 h = 3 600 s d (day) 1 d = 86 400 s Mass kg (kilogramme) g (gramme) 1 g = 10 -3 kg t (ton) 1 t = 10 3 kg Mass density kg/m 3 kg/l 1 kg/l = 10 3 kg/m 3 Temperature K (kelvin) °C (degree Celsius) 0 °C = 273.15 K Difference of temperature K (kelvin) °C (degree Celsius) 1 °C = 1 K Force N (newton) -- 1 N = 1 kg ⋅ m/s 2 Pressure Pa (pascal) bar (bar) 1 bar = 10 5 Pa 1 Pa = 1 N/m 2 Stress N/m 2 N/mm 2 1 N/mm 2 = 1 MPa Work KWh (kilowatt hour) 1 kWh = 3.6 MJ Energy J (joule) 1 J = 1 N ⋅ m = 1 W ⋅ s Quantity of heat eV (electronvolt) 1 eV = 0.1602 ⋅ 10 -18 J Power W (watt) -- 1 W = 1 J/s = 1 N ⋅ m/s Kinematic viscosity m 2 /s mm 2 /s 1 mm 2 /s = 10 -6 m 2 /s Dinamic viscosity Pa ⋅ s mPa ⋅ s 1 mPa ⋅ s = 10 -3 Pa ⋅ s Activity Bq (becquerel) Dose equivalent Sv (sievert)
Page 1 and 2: Recommendations on the Transport of
Page 3 and 4: 16. 4.1.4.1, P802 (1) After 4B, ins
Page 5 and 6: Copyright@United Nations, 2011. All
Page 13 and 14: Recommendations on the TRANSPORT OF
Page 15 and 16: Recommendations on the TRANSPORT OF
Page 25 and 26: 2.8 Appearance at normal transport
Page 27 and 28: 4.9 Does the substance have oxidizi
Page 41 and 42: CHAPTER 1.1 GENERAL PROVISIONS Intr
Page 43 and 44: 1.2.1 Definitions CHAPTER 1.2 DEFIN
Page 45 and 46: Consignee means any person, organiz
Page 49 and 50: Open cryogenic receptacle means a t
Page 51: Remanufactured packagings include:
Page 55 and 56: The decimal multiples and sub-multi
Page 59 and 60: CHAPTER 1.4 SECURITY PROVISIONS Int
Page 63 and 64: 1.5.1 Scope and application Copyrig
Page 65 and 66: 1.5.2.4 For occupational exposures
Page 69 and 70: 2.0.0 Responsibilities CHAPTER 2.0
Page 75 and 76: 2.0.4 Transport of samples Copyrigh
Page 77 and 78: CHAPTER 2.1 CLASS 1 - EXPLOSIVES In
Page 79 and 80: (e) Division 1.5 Very insensitive s
Page 81 and 82: NOTE 1: Articles of compatibility g
Page 87 and 88: - 67 - Type Includes: / Synonym: De
Page 89 and 90: - 69 - Type Includes: / Synonym: De
Page 91 and 92: 2.1.3.6 Exclusion from Class 1 Copy
Page 93 and 94: 2.2.1 Definitions and general provi
Page 95 and 96: 2.2.3 Mixtures of gases Copyright@U
Page 99 and 100: 2.3.2.6 Hazard grouping based on fl
Page 103 and 104:
2.4.2.2.3.3 For solids which may ca
Page 105 and 106:
Copyright@United Nations, 2011. All
Page 107 and 108:
SELF-REACTIVE SUBSTANCE Concentrati
Page 109 and 110:
Page 111 and 112:
Figure 2.4.1: FLOW CHART SCHEME FOR
Page 113 and 114:
2.4.3 Division 4.2 - Substances lia
Page 115 and 116:
2.4.4.3 Assignment of packing group
Page 117 and 118:
CHAPTER 2.5 CLASS 5 - OXIDIZING SUB
Page 119 and 120:
2.5.2.3.1.2 The classification test
Page 121 and 122:
- 101 - ORGANIC PEROXIDE Concentrat
Page 123 and 124:
- 103 - Copyright@United Nations, 2
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Notes on 2.5.3.2.4: 1) Diluent type
Page 133 and 134:
Page 135 and 136:
Exit E Box 11 Figure 2.5.1: FLOW CH
Page 137 and 138:
CHAPTER 2.6 CLASS 6 - TOXIC AND INF
Page 139 and 140:
2.6.2.2.4.2 The criteria for inhala
Page 141 and 142:
Page 143 and 144:
(a) Classify the formulation accord
Page 145 and 146:
INDICATIVE EXAMPLES OF INFECTIOUS S
Page 147 and 148:
2.6.3.2.3.7 Except for: Copyright@U
Page 149 and 150:
CHAPTER 2.7 CLASS 7 - RADIOACTIVE M
Page 151 and 152:
Page 153 and 154:
Gold (79) Radionuclide (atomic numb
Page 155 and 156:
Radionuclide (atomic number) A1 A2
Page 157 and 158:
Page 159 and 160:
Osmium (76) Radionuclide (atomic nu
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
2.7.2.2.4 For mixtures of radionucl
Page 171 and 172:
(b) SCO-II: A solid object on which
Page 173 and 174:
2.7.2.3.3.8 For specimens which com
Page 175 and 176:
Page 177 and 178:
For mixtures of radionuclides whose
Page 179 and 180:
2.8.1 Definition CHAPTER 2.8 CLASS
Page 181 and 182:
CHAPTER 2.9 CLASS 9 - MISCELLANEOUS
Page 183 and 184:
Other substances or articles presen
Page 185 and 186:
Page 187 and 188:
NOTE 1: The organisms fish, crustac
Page 189 and 190:
2.9.3.4.2 The approach for classifi
Page 191 and 192:
2.9.3.4.4.2 Dilution 2.9.3.4.4.2.1
Page 193 and 194:
2.9.3.4.5.3 When applying the addit
Page 195 and 196:
2.9.4 Lithium batteries Copyright@U
Page 197 and 198:
Page 199 and 200:
3.1.1 Scope and general provisions
Page 201 and 202:
3.1.2.8 Generic or “not otherwise
Page 203 and 204:
Page 205 and 206:
UN No. Name and description Copyrig
Page 207 and 208:
UN No. Name and description Class o
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Page 285 and 286:
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
Page 293 and 294:
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
Page 303 and 304:
Page 305 and 306:
Page 307 and 308:
Page 309 and 310:
Page 311 and 312:
Page 313 and 314:
Page 315 and 316:
Page 317 and 318:
Page 319 and 320:
Page 321 and 322:
Page 323 and 324:
Page 325 and 326:
Page 327 and 328:
Page 329 and 330:
Page 331 and 332:
(a) Fusee matches are matches the h
Page 333 and 334:
308 Fish scrap or fish meal shall c
Page 335 and 336:
Fuel cell cartridge design types us
Page 337 and 338:
Page 339 and 340:
Page 341 and 342:
Page 343 and 344:
CHAPTER 3.4 DANGEROUS GOODS PACKED
Page 345 and 346:
3.5.1 Excepted quantities CHAPTER 3
Page 347 and 348:
(ii) Where the sample is in the sha
Page 349 and 350:
Page 351 and 352:
Page 353 and 354:
Class or Division Subsidiary Risk C
Page 355 and 356:
Page 357 and 358:
Page 359 and 360:
Page 361 and 362:
Page 363 and 364:
Page 365 and 366:
Page 367 and 368:
Page 369 and 370:
Page 371 and 372:
APPENDIX B GLOSSARY OF TERMS Cautio
Page 373 and 374:
BOOSTERS BOMBS, PHOTO-FLASH; BOMBS
Page 375 and 376:
CHARGES, SHAPED, without detonator
Page 377 and 378:
EXPLOSIVE, BLASTING, TYPE D Substan
Page 379 and 380:
IGNITERS Articles containing one or
Page 381 and 382:
PROPELLANTS, LIQUID PROPELLANTS, SO
Page 383 and 384:
Page 385 and 386:
Page 387 and 388:
Name and description Class UN No. N
Page 389 and 390:
Page 391 and 392:
Page 393 and 394:
Page 395 and 396:
Page 397 and 398:
Page 399 and 400:
Page 401 and 402:
Page 403 and 404:
Page 405 and 406:
Page 407 and 408:
Page 409 and 410:
Page 411 and 412:
Page 413 and 414:
Page 415 and 416:
Page 417 and 418:
Page 419 and 420:
Page 421 and 422:
Page 423 and 424:
Page 425 and 426:
Page 427 and 428:
Page 429 and 430:
Page 431 and 432:
Page 433 and 434:
Page 435 and 436:
Page 437 and 438:
Page 439 and 440:
Page 441 and 442:
Page 443 and 444:
Page 445 and 446:
Page 447 and 448:
Page 449 and 450:
Page 451 and 452:
Recommendations on the TRANSPORT OF
Page 453 and 454:
Recommendations on the TRANSPORT OF
Page 455 and 456:
Page 457 and 458:
Page 459 and 460:
Page 461 and 462:
Page 463 and 464:
Page 465 and 466:
Page 467 and 468:
Page 469 and 470:
4.1.1.18 Use of salvage packagings
Page 471 and 472:
sections 4.1.5, 4.1.6, 4.1.7, 4.1.8
Page 473 and 474:
Page 475 and 476:
Page 477 and 478:
Page 479 and 480:
Page 481 and 482:
Page 483 and 484:
Page 485 and 486:
P114(a) PACKING INSTRUCTION (Solid
Page 487 and 488:
Page 489 and 490:
Page 491 and 492:
Page 493 and 494:
Page 495 and 496:
Page 497 and 498:
Page 499 and 500:
Page 501 and 502:
P200 PACKING INSTRUCTION (cont'd) P
Page 503 and 504:
Page 505 and 506:
Page 507 and 508:
Page 509 and 510:
Page 511 and 512:
Page 513 and 514:
Page 515 and 516:
P207 PACKING INSTRUCTION P207 This
Page 517 and 518:
Page 519 and 520:
Page 521 and 522:
Page 523 and 524:
Page 525 and 526:
P502 PACKING INSTRUCTION P502 The f
Page 527 and 528:
Page 529 and 530:
Page 531 and 532:
Page 533 and 534:
Page 535 and 536:
Page 537 and 538:
Page 539 and 540:
Page 541 and 542:
Page 543 and 544:
Page 545 and 546:
IBC520 PACKING INSTRUCTION IBC520 T
Page 547 and 548:
IBC620 PACKING INSTRUCTION IBC620 T
Page 549 and 550:
Page 551 and 552:
Page 553 and 554:
Page 555 and 556:
Page 557 and 558:
equirements. Copyright@United Natio
Page 559 and 560:
Page 561 and 562:
Page 563 and 564:
4.2.1.9.6 Portable tanks shall not
Page 565 and 566:
4.2.1.13.9 For insulated portable t
Page 567 and 568:
(b) When leaking; (c) When damaged
Page 569 and 570:
4.2.4.4 The periodic testing and in
Page 571 and 572:
Page 573 and 574:
T23 PORTABLE TANK INSTRUCTION T23 T
Page 575 and 576:
T50 PORTABLE TANK INSTRUCTION T50 T
Page 577 and 578:
T50 PORTABLE TANK INSTRUCTION (cont
Page 579 and 580:
Page 581 and 582:
Page 583 and 584:
4.2.5.3 Portable tank special provi
Page 585 and 586:
(c) Substances shall not be allowed
Page 587 and 588:
4.3.1 General provisions Copyright@
Page 589 and 590:
4.3.1.16 Before a flexible bulk con
Page 591 and 592:
Page 593 and 594:
5.1.1 Application and general provi
Page 595 and 596:
Page 597 and 598:
Page 599 and 600:
5.2.1 Marking Copyright@United Nati
Page 601 and 602:
5.2.1.6 Special marking provisions
Page 603 and 604:
Page 605 and 606:
container except that on labels for
Page 607 and 608:
5.2.2.2.2 Specimen labels CLASS 1 E
Page 609 and 610:
CLASS 7 Radioactive material (No. 7
Page 611 and 612:
5.3.1 Placarding 5.3.1.1 Placarding
Page 613 and 614:
5.3.2 Marking 5.3.2.1 Display of UN
Page 615 and 616:
CHAPTER 5.4 DOCUMENTATION Introduct
Page 617 and 618:
5.4.1.4.2 Sequence of the dangerous
Page 619 and 620:
5.4.1.5.7 Radioactive material Copy
Page 621 and 622:
Page 623 and 624:
* FOR DANGEROUS GOODS: you must spe
Page 625 and 626:
5.5.1 Deleted. CHAPTER 5.5 SPECIAL
Page 627 and 628:
5.5.3 Special provisions applicable
Page 629 and 630:
Figure 5.5.2 * insert the proper sh
Page 631 and 632:
Page 633 and 634:
6.1.1 General Copyright@United Nati
Page 635 and 636:
6.1.2.7 The following table indicat
Page 637 and 638:
Page 639 and 640:
6.1.3.10 Examples of markings for N
Page 641 and 642:
6.1.4.2.6 Maximum capacity of drum:
Page 643 and 644:
6.1.4.8 Plastics drums and jerrican
Page 645 and 646:
6.1.4.13 Plastics boxes Copyright@U
Page 647 and 648:
6.1.4.17 Plastics film bags 5H4 6.1
Page 649 and 650:
6.1.4.20.1 Inner receptacle 6.1.4.2
Page 651 and 652:
(f) If the outer packaging is inten
Page 653 and 654:
6.1.5.3.2 Special preparation of te
Page 655 and 656:
6.1.5.5 Internal pressure (hydrauli
Page 657 and 658:
CHAPTER 6.2 REQUIREMENTS FOR THE CO
Page 659 and 660:
6.2.1.3.4 Individual pressure recep
Page 661 and 662:
6.2.1.5.2 On an adequate sample of
Page 663 and 664:
ISO 4706:2008 Gas cylinders - Refil
Page 665 and 666:
6.2.2.4 Periodic inspection and tes
Page 667 and 668:
6.2.2.5.3 Manufacturer's quality sy
Page 669 and 670:
6.2.2.5.4.8 The application shall i
Page 671 and 672:
pressure receptacle is not the comp
Page 673 and 674:
(d) The designation of the pressure
Page 675 and 676:
Page 677 and 678:
Page 679 and 680:
6.2.3.4 Marking shall be in accorda
Page 681 and 682:
Page 683 and 684:
Page 685 and 686:
Page 687 and 688:
(d) flat on the shortest side; (e)
Page 689 and 690:
Page 691 and 692:
Page 693 and 694:
6.4.7.9 If the containment system f
Page 695 and 696:
Page 697 and 698:
Page 699 and 700:
Page 701 and 702:
Page 703 and 704:
6.4.18 Enhanced water immersion tes
Page 705 and 706:
Page 707 and 708:
Page 709 and 710:
Page 711 and 712:
Page 713 and 714:
Page 715 and 716:
Page 717 and 718:
Page 719 and 720:
Marking shall be applied in the seq
Page 721 and 722:
6.5.2.4 Marking of remanufactured c
Page 723 and 724:
6.5.4.4.3 A report of each inspecti
Page 725 and 726:
Page 727 and 728:
Page 729 and 730:
Page 731 and 732:
6.5.6.3 Preparation of IBCs for tes
Page 733 and 734:
6.5.6.5.5 Criteria for passing the
Page 735 and 736:
(b) For IBCs of types 31H1, 31H2, 3
Page 737 and 738:
6.5.6.10 Tear test 6.5.6.10.1 Appli
Page 739 and 740:
6.5.6.14 Test report Copyright@Unit
Page 741 and 742:
6.6.1 General Copyright@United Nati
Page 743 and 744:
6.6.3.2 Examples of the marking 50
Page 745 and 746:
Page 747 and 748:
6.6.5.2.2 In the drop tests for liq
Page 749 and 750:
6.6.5.3.4 Drop test 6.6.5.3.4.1 App
Page 751 and 752:
CHAPTER 6.7 REQUIREMENTS FOR THE DE
Page 753 and 754:
Page 755 and 756:
6.7.2.2.14 The values of yield stre
Page 757 and 758:
6.7.2.4.7 When in the applicable po
Page 759 and 760:
(b) A liquid tight closure at the e
Page 761 and 762:
6.7.2.12.2 The combined delivery ca
Page 763 and 764:
6.7.2.12.2.3 Minimum required rate
Page 765 and 766:
6.7.2.17.5 When portable tanks are
Page 767 and 768:
(d) Missing or loose bolts or nuts
Page 769 and 770:
Figure 6.7.2.20.1: Example of ident
Page 771 and 772:
Page 773 and 774:
(b) For steels with no clearly defi
Page 775 and 776:
6.7.3.5 Service equipment Copyright
Page 777 and 778:
where: 0. 82 FA Q = 12. 4 LC - 317
Page 779 and 780:
There shall be no obstruction in an
Page 781 and 782:
Page 783 and 784:
(f) Materials (i) Shell material(s)
Page 785 and 786:
Page 787 and 788:
6.7.4.2.13 Under each of the forces
Page 789 and 790:
Page 791 and 792:
6.7.4.8.2 The rated flow capacity m
Page 793 and 794:
6.7.4.14.3 The initial inspection a
Page 795 and 796:
(d) Pressures (i) MAWP (in bar gaug
Page 797 and 798:
6.7.4.15.3 If a portable tank is de
Page 799 and 800:
6.7.5.3.3 For filling and discharge
Page 801 and 802:
6.7.5.10 MEGC supports, frameworks,
Page 803 and 804:
the inspection and test, the test p
Page 805 and 806:
CHAPTER 6.8 REQUIREMENTS FOR THE DE
Page 807 and 808:
6.8.4.3 Vehicles shall comply with
Page 809 and 810:
6.8.5.3.6.2 Preparation for testing
Page 811 and 812:
8. Characteristics of test contents
Page 813 and 814:
Page 815 and 816:
Page 817 and 818:
Page 819 and 820:
oken, missing or otherwise inoperat
Page 821 and 822:
Page 823 and 824:
(c) Inform the appropriate public h
Page 825 and 826:
Page 827 and 828:
7.2.1 Application and general provi
Page 829 and 830:
Page 831 and 832:
TS-R-1 UN 101 1.5.1.1 102 X 103 1.1
Page 833 and 834:
TS-R-1 UN 667 6.4.10.1 668 6.4.10.2
show all

Corrigendum - REACH24H Consulting Group

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?