Instruction Handbook - TA Triumph-Adler
Instruction Handbook - TA Triumph-Adler Instruction Handbook - TA Triumph-Adler
Some label paper is manufactured with an extra margin of top sheet around the edge. Do not remove the extra top sheet from the carrier sheet until after printing is finished. The table below lists the specifications for adhesive label paper. Postcards Up to 10 postcards can be loaded at a time. Fan the stack of postcards and align the edges before loading them in the MP tray. Make sure the postcards you are going to set are not curled. Feeding curled postcards may cause paper jams. Some postcards have rough edges on the back (those are created when the paper is cut). In this case, put the postcards on a flat place and rub the edges with, for example, a ruler to smooth them. Envelopes Acceptable Top sheet Carrier sheet Unacceptable Item Specification Weight of top sheet 44 to 74g/m² (12 to 20 lb/ream) Composite weight 104 to 151g/m² (28 to 40 lb/ream) Thickness of top sheet 0.086 to 0.107mm (3.9 to 4.2 mils) Composite thickness 0.115 to 0.145mm (4.5 to 5.7 mils) Moisture content 4 to 6% (composite) Up to 5 envelopes can be loaded at a time. Envelopes should be fed in the face-up position, right edge first. Since the composition of an envelope is more complex than that of ordinary paper, it is not always possible to ensure consistent printing quality over the entire envelope surface. Normally, envelopes have a diagonal grain direction. Refer to Paper Grain on page 2-6. This direction can easily cause wrinkles and creases when envelopes pass through the printer. Before purchasing envelopes, make a test print to check whether the printer accepts the envelope. • Do not use envelopes that have an encapsulated liquid adhesive. • Avoid a long printing session for envelopes only. Extended envelope printing can cause premature printer wear. • If jams occur, try setting less envelopes on the MP tray. • To avoid jams caused by curled envelopes, stack no more than 10 printed envelopes on the output tray. 2-8 Loading Paper
Thick Paper Fan the stack of paper and align the edges before loading them in the MP tray. Some types of paper have rough edges on the back (those are created when the paper is cut). In this case, put the paper on a flat place and rub the edges once or twice with, for example, a ruler to smooth them. Feeding rough edged paper may cause paper jams. Note If the paper jams even after you smooth it out, load the paper in the MP Tray with the leading edge raised up a few millimeters as shown in the illustration. Colored Paper Colored paper should satisfy the same conditions as white bond paper. Refer to Paper Specifications on page 2-2. In addition, the pigments used in the paper must be able to withstand the heat of fusing during the printing process (up to 200°C or 392°F). Preprinted Paper Preprinted paper should satisfy the same conditions as white bond paper. Refer to Paper Specifications on page 2-2.The preprinted ink must be able to withstand the heat of fusing during the printing process, and must not be affected by silicone oil. Do not use paper with any kind of surface treatment, such as the type of paper commonly used for calendars. Recycled paper Select recycled paper that meets the same specifications as the white bond paper except for whiteness. Refer to Paper Specifications on page 2-2. Note Before purchasing recycled paper, test a sample on the machine and check that the printing quality is satisfactory. Loading Paper 2-9
- Page 1 and 2: Instruction Handbook LP 4130 | 4135
- Page 3: Contents 1 Machine Parts ..........
- Page 6 and 7: iv Legal Information Notice on Soft
- Page 8 and 9: vi 1. the equivalent of U.S. $25,00
- Page 10 and 11: viii Compliance and Conformity This
- Page 12 and 13: x Caution Labels Laser inside the p
- Page 14 and 15: xii Safety Instructions Regarding t
- Page 16 and 17: xiv 11-13/16" (300mm) Installation
- Page 18 and 19: xvi Precautions for Use Cautions wh
- Page 20 and 21: xviii About the Operation Guide Thi
- Page 23 and 24: 1 Machine Parts This chapter identi
- Page 25 and 26: 10 11 12 13 Components at the Rear
- Page 27 and 28: Indicators Indicator Status Meaning
- Page 29 and 30: 2 Loading Paper This chapter explai
- Page 31 and 32: Paper cassette 356mm (14 inches) 14
- Page 33 and 34: Basis weight Basis weight is the we
- Page 35: Special Paper The following types o
- Page 39 and 40: Preparing the Paper After removing
- Page 41 and 42: Note Do not load paper above the tr
- Page 43 and 44: 1 2 Correct Incorrect Correct Corre
- Page 45 and 46: 3 Connecting and Printing This chap
- Page 47 and 48: Installing the Printer Driver Ensur
- Page 49 and 50: Custom Mode Use Custom Mode if you
- Page 51 and 52: 9 Click the plus symbol (+) to add
- Page 53 and 54: Printing This section explains the
- Page 55 and 56: Screen Overview The screen overview
- Page 57 and 58: Appearance Tab The Appearance tab i
- Page 59 and 60: Status Tab The Status tab displays
- Page 61 and 62: Others Tab The Others tab enables y
- Page 63 and 64: 4 Maintenance This chapter explains
- Page 65 and 66: Replacing the Toner Container This
- Page 67 and 68: 6 Turn the lock lever to the lock p
- Page 69 and 70: 4 Place the drum unit flat on a cle
- Page 71 and 72: Prolonged Non-Use and Moving of the
- Page 73 and 74: 5 Troubleshooting This chapter expl
- Page 75 and 76: Print Quality Problems Printed Resu
- Page 77 and 78: Understanding Indicators The indica
- Page 79 and 80: Indicator Meaning [Ready] indicator
- Page 81 and 82: Indicator Meaning Remedy A paper ja
- Page 83 and 84: Cleaning Paper Jams If paper jams i
- Page 85 and 86: Paper Cassette/Paper Feeder 1 Pull
Some label paper is manufactured with an extra margin of top sheet<br />
around the edge. Do not remove the extra top sheet from the carrier<br />
sheet until after printing is finished.<br />
The table below lists the specifications for adhesive label paper.<br />
Postcards<br />
Up to 10 postcards can be loaded at a time. Fan the stack of postcards<br />
and align the edges before loading them in the MP tray. Make sure the<br />
postcards you are going to set are not curled. Feeding curled postcards<br />
may cause paper jams.<br />
Some postcards have rough edges on the back (those are created when<br />
the paper is cut). In this case, put the postcards on a flat place and rub<br />
the edges with, for example, a ruler to smooth them.<br />
Envelopes<br />
Acceptable<br />
Top sheet<br />
Carrier sheet<br />
Unacceptable<br />
Item Specification<br />
Weight of top sheet 44 to 74g/m² (12 to 20 lb/ream)<br />
Composite weight 104 to 151g/m² (28 to 40 lb/ream)<br />
Thickness of top sheet 0.086 to 0.107mm (3.9 to 4.2 mils)<br />
Composite thickness 0.115 to 0.145mm (4.5 to 5.7 mils)<br />
Moisture content 4 to 6% (composite)<br />
Up to 5 envelopes can be loaded at a time. Envelopes should be fed in<br />
the face-up position, right edge first.<br />
Since the composition of an envelope is more complex than that of<br />
ordinary paper, it is not always possible to ensure consistent printing<br />
quality over the entire envelope surface.<br />
Normally, envelopes have a diagonal grain direction. Refer to Paper<br />
Grain on page 2-6. This direction can easily cause wrinkles and creases<br />
when envelopes pass through the printer. Before purchasing envelopes,<br />
make a test print to check whether the printer accepts the envelope.<br />
• Do not use envelopes that have an encapsulated liquid adhesive.<br />
• Avoid a long printing session for envelopes only. Extended envelope<br />
printing can cause premature printer wear.<br />
• If jams occur, try setting less envelopes on the MP tray.<br />
• To avoid jams caused by curled envelopes, stack no more than 10<br />
printed envelopes on the output tray.<br />
2-8 Loading Paper