Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
22. Heating operation with firewood<br />
Stove OFF 13:45<br />
Burner OFF<br />
O u t p u t < | | | | | | - - - - ><br />
Stove OFF 13:45<br />
Burner activation<br />
O u t p u t < | | | | | | - - - - ><br />
Stove OFF 13:45<br />
Firewood operation<br />
O u t p u t < | | | | | | - - - - ><br />
Stove OFF 13:45<br />
fig. 59<br />
fig. 60<br />
fig. 61<br />
Firewood operation<br />
O u t p u t < | | | | | | - - - - ><br />
fig. 62<br />
Ignition of firewood <strong>manual</strong>ly operated<br />
• Set the regulator for primary air (bottom) to level 3 and set the regulator<br />
for secondary air to level 6.<br />
• Open heating door, load 2 to 3 small pieces of firewood or wood-shavings<br />
onto the grate.<br />
• Place 2 to 3 small logs on top of them and light them.<br />
• Close heating door, leave the ash door just a crack open and allow the fire<br />
to burn brightly<br />
• Pull damper (start-up flap) handle (see instruction <strong>manual</strong> stove).<br />
Close ash door and damper (start-up flap) after the preheating phase is complete.<br />
The display still shows StOve OFF or BurNer OFF (figure 58).<br />
Ignition of firewood by means of pellet burner<br />
• Do not open the damper (start-up flap)!<br />
• If the firewood continues to burn for an extended period, set the regulators<br />
for primary air (bottom) and secondary air (top) according to the enclosed<br />
operating instructions of the stove.<br />
• Open heating door, place 2 or three small pieces of firewood (beech wood)<br />
onto the grate (1.6 kg to 2 kg according to the operating instructions of<br />
the stove)<br />
• Close heating door.<br />
Press the button once in the top level of the menu.<br />
The display StOve ON as well as the operating status BurNer activatiON<br />
appears (figure 59).<br />
Because of the increased output caused by the burning of firewood, the pellet<br />
burner switches to operation with firewood, the display shows the operating<br />
status FireWOOD OPeratiON (figure 60).<br />
Should no further increase in the output be identified while the stove is operating<br />
on firewood, the appliance automatically returns to Operation with pellets<br />
if the appliance is switched ON.<br />
If the stove continues to burn firewood, the pellet burner shuts down automatically.<br />
If no more firewood is added, the appliance changes after a safety<br />
period automatically to heating operation with pellets according to the pre-set<br />
heating output.<br />
Adding of firewood during heating operation with pellets<br />
If the stove is loaded with more firewood while the appliance is being heated<br />
with pellets, the appliance first switches to operation with firewood.<br />
The display StOve ON as well as the operating status FireWOOD OPeratiON<br />
appears (figure 61).<br />
In the event that the appliance is operated with a low heating output, it may occur<br />
that the operation with firewood will not be immediately identified, thus the<br />
ignition!<br />
If the stove continues to burn firewood, the pellet burner shuts down automatically.<br />
If no more firewood is added, the appliance changes after a safety period<br />
automatically to heating operation with pellets with the pre-set heating output.<br />
If the firewood continues to burn for an extended period, set the regulator for<br />
primary air (bottom) to level 3 and the regulator for secondary air (top) to level 6.<br />
CAUTION: During operation with firewood, there is no automatic adjustment of the<br />
output through the pellet stove control. The adjustment of the output depends on<br />
the amount of fuel added. With appliances featuring a central heating insert, only<br />
the heating circuit pump (provided by the customer) is switched on or off.<br />
page 19