You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
20. Operating the stove for the first time<br />
21. Heating operation with pellets<br />
page 18<br />
Stove ON 13:45<br />
Burner start-up<br />
O u t p u t < | | | | | | - - - - ><br />
Stove ON 13:45<br />
fig. 57<br />
Burner ON<br />
O u t p u t < | | | | | | - - - - ><br />
fig. 58<br />
• Do not leave small children unattended in the vicinity of the stove: the<br />
heating system is not childproof!<br />
• Prior to the first start-up all connections (chimney flue connection, power<br />
supply, etc.) are to be checked.<br />
• The viewing glass as well as the door become very hot when the stove is in<br />
use (temperatures up to 300 °C). Pay attention to the fact that these parts<br />
must not be touched when the stove is in operation.<br />
• Keep the firebox door closed at all times, even if the stove is not in use.<br />
• Make sure that no objects are in the combustion chamber, in the firebox as<br />
well as in the oven.<br />
• Only after the installation is completed in accordance with the <strong>user</strong> <strong>manual</strong><br />
and installation instructions, is it allowed to charge the storage container<br />
with pellets (at least 5 kg).<br />
General note – Surfaces<br />
Only high-quality air-drying varnish is used which does not smell nor give off<br />
fumes when heated up for the first time if it is allowed to dry completely (at<br />
room temperature). If the appliance is heated up shortly before the varnish has<br />
hardened, an unpleasant smell and fume will be temporarily produced. Please<br />
give the room where the appliance is located a good airing.<br />
Charging the storage container<br />
Make sure that you use approved pellets which conform to ÖNORM M7135/DIN<br />
51731 – see imprint on the pellets bags or consult your pellets supplier. Open<br />
the container lid. To avoid raising of dust, pour pellets slowly and not from too<br />
high a position. After feeding the pellets, the lid is to be closed and should<br />
remain closed during operation.<br />
• While the appliance operates on pellets, the damper (start-up flap) (see<br />
instruction <strong>manual</strong> stove) must not be opened!<br />
• Set both stove air regulators to level “0”!<br />
The regulation is determined by the specified boiler set-point temperature<br />
(75°C or 65°C respectively, see setting SUMMER /WINTER).<br />
Should the boiler set-point temperature be exceeded by 10°C, the appliance<br />
shuts down automatically display burner OFF and switches on again once the<br />
boiler set-point temperature has fallen below the value by 3 °C.<br />
The appliance might resume operation automatically at any time, therefore please<br />
note the information in point External Release /Remote control unit!<br />
Switching the appliance on<br />
Press the button once in the top level of the menu.<br />
The display StOve ON appears as well as the operating status burner start-up<br />
(figure 56).<br />
The appliance switches on.<br />
Setting the heating output<br />
Setting of the heating output in the top level of the menu (figure 57).<br />
Reduce heating output by pressing the button .<br />
Increase heating output by pressing the button .<br />
Adjustment range heating output:<br />
3 - 10 for air heaters (P6)<br />
5 - 10 for central heating appliances (P7, type designation -Z)<br />
If the heating output is not sufficient although it has been set at the highest<br />
level, the temperature can be increased by loading firewood.
Change language