Mechanical Joints, Terminations & Connectors for ... - TransNet

More documents

Recommendations

Info

11kV Bushing Boots heat-shrinkable The bushing boot size range information listed below is applicable only to terminations installed using mechanical lugs Part Number Inline Right Angle Description XLPE (M Kits) PILC (PTM Kits) RSRB 4024 RSRB 4044 11kV Heatshrink Bushing Boots (Set of 3) 16-95mm 2 16-70mm 2 RSRB 4026 RSRB 4046 11kV Heatshrink Bushing Boots (Set of 3) 120-300mm 2 95-300mm 2 Note: For bushing boots rated to 22 or 33kV please contact CSL 11kV Bushing Boots cold applied 11kV Inline Joint Kits for MIND Paper Screened/Belted Cables C/w Mechanical Connectors Part Number Description Cable Bushing Diameter RCAB 4120 11kV Silicon Push On Bushing Boots (Set of 3) 35-400mm2 46-70mm 11kV Trifurcating Kits for XLPE cables Part Number 750mm Tail 1500mm Tail Description Size Range TRKT-11-1635-750 TRKT-11-1635-1500 11kV Trifurcating Kit 16-35mm2 TRKT-11-35150-750 TRKT-11-35150-1500 11kV Trifurcating Kit 35-150mm2 TRKT-11-185400-750 TRKT-11-185400-1500 11kV Trifurcating Kit 185-400mm2 Note: For longer tail lengths such as 2m tails indicate as per example TRKT-11-185400-2000 Other kits for higher voltages are also available 28
• Heat shrinkable bushing boots • Right angle or inline versions available • Wide size application range • Push on cold applied bushing boots • Suits right angle or inline bushing applications • Wide application range • Silicon material Trifurcating kits provide the facility to terminate 3/Core XLPE cable into small cable boxes where the dimensions required for a standard 3/Core termination are diffi cult to maintain. This simple solution gives you the advantage of performing a crossover outside the cable box, and the installation of a single core cable accessories rather than a 3/Core. Kit consists of a full length heat-shrink tube (to allow for re-jacketing of the cable cores which lets you cut to length to suit an on site application), breakout boot, phase markers & protection sleeve. 29
Page 1 and 2: Energy Division Mechanical Joints,
Page 3 and 4: Contents 11kV Inline Joints, Transi
Page 5 and 6: • Full range of LV joints availab
Page 7 and 8: • Full range of LV terminations a
Page 9 and 10: • Suitable for Cu or AL (solid or
Page 11 and 12: • Suitable for stranded or solid
Page 13 and 14: • A range of connectors for incor
Page 15 and 16: • A range of connectors for incor
Page 17 and 18: Brass gauze is recommended for use
Page 19 and 20: • Can be designed to network spec
Page 21 and 22: • Complete with mechanical connec
Page 23 and 24: • Eliminates the need for two joi
Page 27: Packaged kit containing: • Termin
Page 33 and 34: • Eliminates the need for two joi
Page 41 and 42: • These connectors are intended a
Page 43 and 44: These lugs are designed for use on
Page 45 and 46: These connectors are designed for u
Page 47 and 48: These connectors are designed for u
Page 49 and 50: • Mechanical repair sleeves are u

Mechanical Joints, Terminations & Connectors for ... - TransNet

Create successful ePaper yourself

Delete template?

Save as template?