Advanced Package Training Scaffolding 2011.1 - Scia-Software GbR

More documents

Recommendations

Info

Combination 4: Into service, Wind parallel Coefficients BG1 Self weight BG2 Self weight toeboards BG3 Service load Main floor BG4 Service load Main floor BG9 Working wind load parallel with facade 22 Advanced Training With the Combinations in Ultimate Limit State, a safety factor γF of 1,50 on the load cases is taken, conformable to the code EN 12811 §10.3.2. The safety factor γM on the material is 1,10. For the serviceability γF and γM shall be taken as 1,00.
4. Results It is recommended to first examine the reac reactions. This way you can check the accuracy of the imported loads and load combinations. The calculation protocol (in the result dialog) should be reviewed as well. The bill of material can also be found in the results menu. In this table the he total length for each cross section is shown. With these results, each user can divide tthe total length of each type of cross section by the length of one member, in order to calculate the total number of ledgers, columns, ... necessary for the construction. Example Scaffolding.esa The results (such as normal force, moment, …) can be viewed per profile type ( (columns, bracings, ledgers). That is why it is recommended to put every cross section in different layer layers. This way it will be easier to review the resul results per cross section type. Apart from reviewing the results, the anchorage forces have to be checked as well. These can be found in “Reactions”. 23 Scaffolding
Page 1 and 2: Advanced Package Training Scaffoldi
Page 3 and 4: Contents 1. Introduction ..........
Page 5 and 6: 1. Introduction 5 Scaffolding This
Page 7 and 8: Materials 7 Scaffolding For the mat
Page 9 and 10: FLOOR BOARDS 9 Scaffolding The inpu
Page 11 and 12: END INPUT OF CONSTRUCTION 11 Scaffo
Page 13 and 14: q2: Partial area load (EN12811-1, 6
Page 15 and 16: Load Case 1: Self Weight 15 Scaffol
Page 17 and 18: 17 Scaffolding In the example discu
Page 19 and 20: 1 2 q p ( z) = ce ( z) ⋅ qb = ce
Page 21: q p e 21 Scaffolding EN 12811-1 §6
Page 25 and 26: 6. Scaffolding SLS Check - EN 12811
Page 27 and 28: 7. Steel Code Check ULS Check - EN
Page 29 and 30: Stability Check Buckling data 29 Sc
Page 31 and 32: - Go to the menu “Steel -> Check
Page 33 and 34: 8. Scaffolding ULS Check - EN 12811
Page 35 and 36: 9. Non-Linear Combinations Overview
Page 37 and 38: 1a 5.2.2(3)c lb based on a global b
Page 39 and 40: These inclination functions are ent
Page 41 and 42: 41 Scaffolding The buckling curve u
Page 43 and 44: 43 Scaffolding In this figure, the
Page 45 and 46: Start Choose ΔF u0 = 0 F0 = 0 F =
Page 47 and 48: 47 Scaffolding As specified, the Ne
Page 49 and 50: 49 Scaffolding In the results menu,
Page 51 and 52: ∙ + ∙ = ∙ The equation f
Page 53 and 54: Example Stability_Imperfe Imperfect
Page 55 and 56: Buckling Shape [-] A polynomial has
Page 57 and 58: 57 Scaffolding Using this combinati
Page 59 and 60: 12. Input Hinge Types and non-linea
Page 61 and 62: The rigidities are filled out and t
Page 63 and 64: 63 Scaffolding It is assumed that t
Page 65 and 66: 13. Scaffolding - Coupler Check Whe
Page 67 and 68: The internal force My for this beam
Page 69 and 70: Example ULS Check - Scaffolding che
Page 71 and 72: 71 Scaffolding
Page 73 and 74:
73 Scaffolding Where L is the membe
Page 75 and 76:
75 Scaffolding
Page 77 and 78:
Shear The design value of the shear
Page 79 and 80:
For a solid bar, round tube and hho
Page 81 and 82:
17. Template To create a template,
Page 83 and 84:
3. Inserting the user block into an
Page 85 and 86:
Annex A: Wind pressure versus Wind
show all

Advanced Package Training Scaffolding 2011.1 - Scia-Software GbR

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?