View Document Here - Hanford Site

""lived as
SURFACE PREPARATION
^"INCRETE: New concrete should be well cured (26 days al 7C •F). fr ee d dl seating and hardening compounds, and any other contaminants
as oil, grease end chemicals. Old cement shell be clean and free d de same as above plus old coatings and p oi nts. Shat blasting to a 8.5
:dUe Is the recommended method c( su rface preparafbn. Acid etc hing Is approved with Sleelede Clean b Etch f ollowed by neutralizing with
"is ammonle In wader (23 cups per S gdllon a of weier). Double etch wrh Clean Q Etch only to too mesh sandpaper profile. Do not use murlege
ackl eotu lonl Clean 6 Etch co ntains proper b alance of phosphor ic and murlat ic acld to etch without damage to floor( Concrete su rfaces must be
free of hydrostdfo pressure. Application may be made to a damp, uncured concrete floor N Monomid Clear Seder Is applied first and slowed to
d ry. Do not apply over curing agents, hardeners, dl, grea, seor
other I tervenlrp barriers. H applying over Ep o-Lior 121 or Monomld Clear Seder,
apply when seder Is slightly tacky to assure chem ical bond. If seder Is allowed to d ry, sanding is required before appl ication of Colodop. Use
Steelcots Wall-Nu to fill holes and cracks. Sand smooth before applying Color-Top.
WOOD AND PLYWOOD: These su rfaces sh elf be clean fr ee d dirt dl. Create and other cordanrllnants. loose boards sh al l be ro- alied
or screwed end courder•sunk. Rot or severe contaminat ion shall be cut to sound surface and repaired repair with new wood or f illed w d
it h Sta eloe
Color Top, The su rface sh elf be mechlne sanded to a smooth, open-pored state. Apply Colonop over Moramkl Geer Seder or Epo4.aac 112 Deep
Psnetraing Seder.
STEEL' Consu lt Steaieote's Tec hnical Service Department
MIXING AND APPLICATION FOR USE ASA COATING: Do not satimpttomuthe material VIt has boon ston¢Inaoold arrestor
a period Of firms. The material must be wamnd to room tempertlure(d least Wi t.) so them a sler mbdrp can be obtained. MdwW can be warmed
to WT.by sitting In warm w at er or a warm room for a period Of time, Warming the mtlertal reduo» the viscosity to that proper corlsktenay for
thorough nmbdfg and eaty applkldbn Do not mbl mars than ors two gallon unit tl atkns for beet resuHe, but M applicdbn Is belnp saooarlplbhsd
M more than one person two, hvo polon ants may be mbad. Mbdng d quentMbe d ors. Nrogdbn unk or man shell bs aocortrpibhed on a ^0
RPM, •KOL• a equ4dent smell paste or dement mortar miser d 6gdbn espaely a morn M6dng writ a paddle or Jtlly^ps mbar Ix by hand b
not noommended except as part d tM KOL mbdn0., farastlr bath oonmporerts to assure untorm odor. Use a pertoraW 61ade In 1st KOL Mae
and mica on tM batk d one Part A to one Part B. Mica 8 rnintrlss by the clock blending vsrtlo +dly with 1st slow speed Jtty m6ret ant oatlnuowty
sorsong the sldewdk d 1st mbdrp coMdrw. At tha end d t! rNnutes, atop, end trarsfar 1st mist b a sapards eleen 1s gallon can scraping down
tM eltdewelle and 1M.mbdng blade to make sun ail moiefW M In tM tIM oars liters pour down 1st oentar d lM second can Bernier for one minus.
^^ONTRO LS: To avoid having unmbcad or partially mbced bdohes t hat tan result In uncured wet apots.a par tially cured NWW or 111011 spots
t k rswssevy to have close mbdng oleoks for each batch Take a 2 to bounce sample of each mbc after oompletion d irik N a wax cup, Writer
time of MIN on a tongue depr essor placed in each cup. 11 mebn al In cup do es not eat up or beg in to not up and/or becort as warm or rat In one
moor tl 76 degrees Fahenheit ¢TOP TH,€ f^P',^,QATON. H paebk+, Put tM aampN h an own at 120 dspnas Fahrenftek for 1Pt2 mtrwAes. M
natertel does not hardM remove unsure mbad mtlsAal Nom surface and rsevdutls mbdrg procedures Il oven not avai{able, a shallow ple pan
lo.d et 6a lad 1»fon m6cin^to a old a short aura of oortrd spaelman. H referrer b stand and/or ahippad attamparatursu above lC'F.,
heoop
0 pal-IHe. ..
eLICATI O N: Mbud Colortop shalt be poured out on floor Immediately after mfdnc Ina snake4 1ke f as hion to a pregnsesued area equal to
he cloaked Mn thicknes s. Spread eye,* with a 144 sanded vWA squapss end erosstdled w ith a 1/S• meek roger with a phenolic oom A br ush
nay be used as required around edges. Lightly mist surface with DIuWA or roll over •WeC nisawfal wfth a•porcupklsa rollorto remove ark bubbles,
! they form. Keep a wet edge and oorttlnus Job without ktertuptbn until completed or completed to a natural l eakpaI t,
AIXING AND APPLICATION INSTRUCTIONS FOR NONSLIP OR SEEC-IN COLOR TOP METHOD:
»e Erpinewing Service Tech ni cal Bulle tin Na C1--SIM,'
JIIXING AND APPLICATION INSTRUCTIONS FOR TROWEL IN METHOD ON COLOR-TOP SYSTEM:
:ate EnginowirV Service Technical Bu lletin No. CT•TOM,
"HYSICAL AND CHEMICAL PROPERTIES: Ses Engineering Se rvice Technical Bulletin No. CTF:
IRUSH: Use a clean, neural brk0e brush
APPLICATION EQUIPMENT
LOLL: Use a cl"j% short nap, incheir roller with a phorictic act* or E-Z PaIrstir'Flal Applicator, Material should be spread with at""
14• serrated equesges and then cross rolled or spread w it h Ind polyurethane appl icator and po rc upine roller.
iegtdsred TM • SM Company
Into
WAITED WARRANT': 1st interstellen orewnted he roin Is. la the bMl of eW knerM00e,
TM Inlorntallan 00ntslned herein It bead upon data leund by our one, at Indo"ndanl te sting lab or atory. It la eonsldsted
change Winter notice.
NO
ALL
THE
~61 at dale at Issusnes. and Is subject le
1006
V t
ti/