MAN-Combics Complete Scale CAW3P CAW3S CAH3-e - Sartorius

More documents

Recommendations

Info

Configuring Weighing Platforms Function Allocation of the J Key for Linearization and Setting/ Deleting the Preload Purpose The J key is normally used for the calibration/adjustment function. The following additional functions can be allocated to the key when the Service mode is activated: – External linearization with default weights – External linearization with entered linearization weights – Internal linearization (for external IS platforms only) – Set preload – Delete preload 3 Once 46 Operating Instructions Combics Complete Scales linearization has been completed, or after a preload has been set or deleted the function of the J key must be reallocated back to its original function in the Setup menu, e.g. external calibration/adjustment with default weights. Procedure t Remove the cap. t Slide the menu access switch to the left (= “open“ position). t Activate the Service mode, see “Service Mode.“ t Select weighing platform “WP 1“ in the “Device Parameters“ menu item. t If the “Internal“ setting is not already activated (marked by “o“), select the setting using the “Q“ or “q“ soft key and confirm with “O.“ y The menu for the “WP-1 INTERNAL“ device parameters is displayed. t Use the “Q“ or “q“ soft key to select and open the “Calibration/ adjustment“ menu using “O.“ y The “CAL key function“ submenu is displayed. t Use the “Q“ or “q“ soft key to select the corresponding menu item and confirm with “l.“ y The menu item is marked by a circle “o.“ Note The functions that can be configured in the “CAL key function“ submenu depends on the selected weighing platform and its configuration data. Functions that cannot be accessed are not displayed in the selection screen. Note The function set in the “CAL key function“ menu is carried out in the normal weighing mode because when you exit the Setup menu the Service mode is deactivated. To perform the function on a digital weighing platform (such as an IS platform), however, it must be carried out in Service mode. t The procedure is as follows: after selecting the desired function and exiting the Setup menu, reactivate Service mode again and then exit the Setup menu immediately by pressing the M key or the “oo“ soft key. y The scale is now in Service mode without this being displayed. t Trigger the previously set function using the J key. y The display shows “S_CAl:“ indicating that the scale is in Service mode. t The corresponding menu item can be selected using the “Select“ soft key and carried out using the J key. t If you cancel the function using the ( key or by restarting the scale using the e key, you will exit the Service mode.
External Linearization with the Factory-Defined Weight (Default Weights) Setup Information – This function is accessible only if the software and the functionality of the connected weighing platform permit this operation. – External linearization when weighing in legal metrology is only possible when the menu access switch is open. – The J key must be assigned the “External linearization“ function, see “Function Allocation of the J Key for Linearization and Setting/Deleting the Preload.“ – Activating the display of geographical data has no effect on this function. 3 Once Configuring Weighing Platforms linearization has been completed, the J key must be reallocated back to its original function in the Setup menu, e.g. external calibration/adjustment with default weights. Procedure t For scales used in legal metrology, slide the menu access switch to the left (= “open“ position). y The display goes out and the device restarts. Then weighing mode is active. t Press ( to unload and zero the scale. t Press J to start the external linearization. y The display “L.EXT.D“ appears briefly. Additional steps are explained in “External Linearization with User-Defined Weights.“ Operating Instructions Combics Complete Scales 47
Page 1 and 2: Operating Instructions Sartorius Co
Page 3 and 4: 2 Warning h Notes on Using this Man
Page 5 and 6: 3 Warning 3 Connect Installation wh
Page 7 and 8: 1 10 CAW3P 19 18 17 16 15 CAW3S | C
Page 9 and 10: CAH3 models: Remove transport locks
Page 11 and 12: 3 Superstructures Shock Resistance
Page 13 and 14: 2 1 5 3 3 Please 4 Attaching the Ca
Page 15 and 16: PS2 COM1 COM2 LED + Display Keypad
Page 17 and 18: 5 1 9 6 Interface Pin Assignment Ch
Page 19 and 20: 6 5 4 2 3 1 Interface Pin Assignmen
Page 21 and 22: Configuring Weighing Platforms Serv
Page 23 and 24: Device Parameters WP1 Internal Cali
Page 25 and 26: Analog/Digital Converter (ADC) Purp
Page 27 and 28: Analog/Digital Converter (ADC) Conf
Page 29 and 30: Configuring Weighing Platforms Mult
Page 31 and 32: The displays depicted in the next t
Page 33 and 34: Configuring Weighing Platforms Proc
Page 35 and 36: C.EXT.D C.EXT.DEF. Altitud C.EXT.DE
Page 37 and 38: Entering Adjustment and Linearizati
Page 39 and 40: C.EXT.D C.EXT.DEF. t Use the “O
Page 41 and 42: -------------------- 14.01.2010 13:
Page 43 and 44: 3 If 3 Adjustment h a serious opera
Page 45: If the weighing platform has multip
Page 49 and 50: -------------------- 14.01.2010 13:
Page 51 and 52: -------------------- 14.01.2010 13:
Page 53 and 54: ID D Toggles to the Info mode: Pres
Page 55 and 56: Saving Settings in Weighing Mode Yo
Page 57 and 58: Data in Tare Memory, Calculated Val
Page 59 and 60: Configuration You can configure the
Page 61 and 62: Setting up Password Protection t Pr
Page 63 and 64: Setup Overview (Parameters) o = Fac
Page 65 and 66: Device Parameters WP 1 Internal 1 )
Page 67 and 68: Device Parameters 1 ) Not with 8 da
Page 69 and 70: Device Parameters COM 1 1 ) Max. 2
Page 71 and 72: Device Parameters I/O control Bar c
Page 73 and 74: Device Parameters Operating paramet
Page 75 and 76: Setup Info Language Service Termina
Page 77 and 78: Automatic Taring The first weight o
Page 79 and 80: Adjustment/Configuration counter fo
Page 81 and 82: Tare the scale by placing a contain
Page 83 and 84: -------------------- 24.10.2010 10:
Page 85 and 86: G# + 6.433 kg T + 4.183 kg PT2 + 0.
Page 87 and 88: Operation Features Which of the fol
Page 89 and 90: External calibration Nom. + 10000 g
Page 91 and 92: SQmin Function Operation Purpose To
Page 93 and 94: Procedure t Place the container for
Page 95 and 96: Using Individual ID Code Example En
Page 97 and 98:
Specifications Serial interface: In
Page 99 and 100:
Configuring the Data Interface as a
Page 101 and 102:
Data Input Format Data Interfaces Y
Page 103 and 104:
Output of the weight value +1255.7
Page 105 and 106:
h Example: Output of the weight val
Page 107 and 108:
There are several actions that gene
Page 109 and 110:
HEADER LINE1 HEADER LINE2 14.01.201
Page 111 and 112:
“Checkweighing” Application The
Page 113 and 114:
GMP-compliant printouts “Lineariz
Page 115 and 116:
Error Codes Error Codes Errors are
Page 117 and 118:
2 Disconnect 2 If 2 Do 2 Disconnect
Page 119 and 120:
Disposal If the packaging is no lon
Page 121 and 122:
CAW*S... Model Resolutions Resoluti
Page 123 and 124:
Device Dimensions Dimensions of CAH
Page 125 and 126:
Accessories Product Order No. Verif
Page 127 and 128:
Product Order No. Mechanical access
Page 129 and 130:
Declaration of Conformity Declarati
Page 131 and 132:
Declarations of Conformity Operatin
Page 133 and 134:
Plates and Markings Operating Instr
Page 135 and 136:
Plates and Markings Operating Instr
Page 137 and 138:
Appendix: Guide to Verification of
Page 139 and 140:
Operating Instructions Combics Comp
Page 141 and 142:
Explosion-safe area 3. Connecting W
Page 143:
11.05.2012 Klausgrete Designation D
Page 148:
Sartorius Weighing Technology GmbH
show all

MAN-Combics Complete Scale CAW3P CAW3S CAH3-e - Sartorius

Create successful ePaper yourself

Delete template?

Save as template?