MAN-Combics Complete Scale CAW3P CAW3S CAH3-e - Sartorius

More documents

Recommendations

Info

Configuring Weighing Platforms 34 Operating Instructions Combics Complete Scales Entering Gravity t Use the “Q“ or “q“ soft key to select the corresponding input field. t Enter gravity in m/s 2 via the keypad and confirm using the “l“ soft key. Permissible value range: 9.700000 d < gravity 2 d < 9.900000 In the example shown here, the value for gravity has been changed. The new value, 9.810000 m/s2 applies to the setting “Germany (Zone D).” t Press the “o“ soft key to exit the Input menu. t Use the “Q“ soft key to select the “Save parameters“ menu item. t Use the “Q“ soft key to select “Yes“ and use the “l“ soft key to confirm. y The message “Data stored“ appears briefly. The program then returns to the “No“ display status. t Press M or “oo“ to exit the Setup menu. t Slide the menu access switch to the right (= “closed“ position) and reattach the cap. y The display goes out and the device restarts. Then weighing mode is active. Adjusting Scales in Operating Mode See also “Calibration and Adjustment“ in the chapter called “Operation“ t Open the Device parameters menu for the respective weighing platform, (e.g. “WP 1:INTERNAL“). – Open the “Calibration/adjustment“ submenu. – „ CAL key function“ menu item: Setting “Ext. cal./adj.: factory-def. wt.“ (factory setting). – „ Cal/adj. sequence“ menu item: Setting “Cal. then manual adj.“ (factory setting). – „ Activate ext. adj.“ menu item (not for a verifiable configuration): Setting “Activated“ (factory setting). To display geographical data in the Device parameters menu, open the “Operating parameters“ submenu. Menu item “Display geogr. data > On“. t Press ( to unload the scale.
C.EXT.D C.EXT.DEF. Altitud C.EXT.DEF. Latitud C.EXT.DEF. t Press J to start an external adjustment. y The display “C.EXT.D“ appears briefly. In the example, the altitude and latitude of the installation location are being entered. y The display “Altitud“ appears briefly. y The altitude at the place of installation is displayed in meters above sea level - here, the altitude for “Germany (Zone D).” t Press J to confirm the displayed value or press ( to cancel the adjustment. y The display “Latitud“ appears briefly. Configuring Weighing Platforms y The geographical latitude of the place of installation is shown in degrees north or degrees south - here the latitude setting for “Germany (Zone D).” t Press J to confirm the displayed value or press ( to cancel the adjustment. y You are prompted to place the required weight on the platform (e.g.: 5.0 kg). The subsequent steps for completing the calibration/adjustment are described in the chapter entitled “Operation” under “Calibration and Adjustment.” Operating Instructions Combics Complete Scales 35
Page 1 and 2: Operating Instructions Sartorius Co
Page 3 and 4: 2 Warning h Notes on Using this Man
Page 5 and 6: 3 Warning 3 Connect Installation wh
Page 7 and 8: 1 10 CAW3P 19 18 17 16 15 CAW3S | C
Page 9 and 10: CAH3 models: Remove transport locks
Page 11 and 12: 3 Superstructures Shock Resistance
Page 13 and 14: 2 1 5 3 3 Please 4 Attaching the Ca
Page 15 and 16: PS2 COM1 COM2 LED + Display Keypad
Page 17 and 18: 5 1 9 6 Interface Pin Assignment Ch
Page 19 and 20: 6 5 4 2 3 1 Interface Pin Assignmen
Page 21 and 22: Configuring Weighing Platforms Serv
Page 23 and 24: Device Parameters WP1 Internal Cali
Page 25 and 26: Analog/Digital Converter (ADC) Purp
Page 27 and 28: Analog/Digital Converter (ADC) Conf
Page 29 and 30: Configuring Weighing Platforms Mult
Page 31 and 32: The displays depicted in the next t
Page 33: Configuring Weighing Platforms Proc
Page 37 and 38: Entering Adjustment and Linearizati
Page 39 and 40: C.EXT.D C.EXT.DEF. t Use the “O
Page 41 and 42: -------------------- 14.01.2010 13:
Page 43 and 44: 3 If 3 Adjustment h a serious opera
Page 45 and 46: If the weighing platform has multip
Page 47 and 48: External Linearization with the Fac
Page 49 and 50: -------------------- 14.01.2010 13:
Page 51 and 52: -------------------- 14.01.2010 13:
Page 53 and 54: ID D Toggles to the Info mode: Pres
Page 55 and 56: Saving Settings in Weighing Mode Yo
Page 57 and 58: Data in Tare Memory, Calculated Val
Page 59 and 60: Configuration You can configure the
Page 61 and 62: Setting up Password Protection t Pr
Page 63 and 64: Setup Overview (Parameters) o = Fac
Page 65 and 66: Device Parameters WP 1 Internal 1 )
Page 67 and 68: Device Parameters 1 ) Not with 8 da
Page 69 and 70: Device Parameters COM 1 1 ) Max. 2
Page 71 and 72: Device Parameters I/O control Bar c
Page 73 and 74: Device Parameters Operating paramet
Page 75 and 76: Setup Info Language Service Termina
Page 77 and 78: Automatic Taring The first weight o
Page 79 and 80: Adjustment/Configuration counter fo
Page 81 and 82: Tare the scale by placing a contain
Page 83 and 84: -------------------- 24.10.2010 10:
Page 85 and 86:
G# + 6.433 kg T + 4.183 kg PT2 + 0.
Page 87 and 88:
Operation Features Which of the fol
Page 89 and 90:
External calibration Nom. + 10000 g
Page 91 and 92:
SQmin Function Operation Purpose To
Page 93 and 94:
Procedure t Place the container for
Page 95 and 96:
Using Individual ID Code Example En
Page 97 and 98:
Specifications Serial interface: In
Page 99 and 100:
Configuring the Data Interface as a
Page 101 and 102:
Data Input Format Data Interfaces Y
Page 103 and 104:
Output of the weight value +1255.7
Page 105 and 106:
h Example: Output of the weight val
Page 107 and 108:
There are several actions that gene
Page 109 and 110:
HEADER LINE1 HEADER LINE2 14.01.201
Page 111 and 112:
“Checkweighing” Application The
Page 113 and 114:
GMP-compliant printouts “Lineariz
Page 115 and 116:
Error Codes Error Codes Errors are
Page 117 and 118:
2 Disconnect 2 If 2 Do 2 Disconnect
Page 119 and 120:
Disposal If the packaging is no lon
Page 121 and 122:
CAW*S... Model Resolutions Resoluti
Page 123 and 124:
Device Dimensions Dimensions of CAH
Page 125 and 126:
Accessories Product Order No. Verif
Page 127 and 128:
Product Order No. Mechanical access
Page 129 and 130:
Declaration of Conformity Declarati
Page 131 and 132:
Declarations of Conformity Operatin
Page 133 and 134:
Plates and Markings Operating Instr
Page 135 and 136:
Plates and Markings Operating Instr
Page 137 and 138:
Appendix: Guide to Verification of
Page 139 and 140:
Operating Instructions Combics Comp
Page 141 and 142:
Explosion-safe area 3. Connecting W
Page 143:
11.05.2012 Klausgrete Designation D
Page 148:
Sartorius Weighing Technology GmbH
show all

MAN-Combics Complete Scale CAW3P CAW3S CAH3-e - Sartorius

Create successful ePaper yourself

Delete template?

Save as template?