Huron & SNAP Documentation

More documents

Recommendations

Info

Features Operation Object list Add source object Edit object Delete source object BinScape BinScape is a 3D positional-audio simulator based on binaural technology. It can simultaneously render up to 32 sound sources to a single listener position. BinScape uses only 3 DSPs regardless of the number of sound sources and provides for headtracked listening via <strong>SNAP</strong> commands. BinScape can load user definable head and room filters for engineering research applications. • Fixed usage of only 3 DSPs for 3D rendering of 1 to 32 source objects to a single listener. • Simulation of 3 rooms with varied acoustical damping and size properties. • Head tracking is possible by setting channels for BinScape to receive listener position and orientation messages from a tracker tool. • User supplied head and room filters can be loaded. • Can be controlled remotely via <strong>SNAP</strong> commands and the Socket application. Reset object position Select head filter set Figure 25 — Customised BinScape main interface Select Room filter HURON TECHNICAL MANUAL PAGE 73
Page 1:
Huron Technical Manual Software ver
Page 5:
Copyright © 1995-2003 Lake Technol
Page 9:
FCC Declaration (USA only) for Huro
Page 13 and 14:
Table of Contents DISCLAIMER.......
Page 15 and 16:
TABLE OF CONTENTS FEATURES ........
Page 17 and 18:
TABLE OF CONTENTS OPERATION .......
Page 19 and 20:
TABLE OF CONTENTS DC BLOCK.........
Page 21 and 22: TABLE OF CONTENTS THE 96KHZ EQ ....
Page 23: Introduction to the Huron Thank you
Page 26 and 27: Features Applications Note: Any ISA
Page 28 and 29: INTRODUCTION TO THE HURON • Optio
Page 30 and 31: Installing New Hardware Components
Page 32 and 33: ↓ To change the ISA memory addres
Page 35 and 36: ↓ Connecting with the patch panel
Page 37 and 38: Huron System Tools Huron Simulation
Page 39 and 40: General Installation ↓ To install
Page 41: Introduction to the System Tools Th
Page 44 and 45: Operation Starting ↓ To start the
Page 46 and 47: Configuration Functions Internal/Ex
Page 48 and 49: Displaying, Hiding and Terminating
Page 50 and 51: Stopping VRack ↓ To exit the VRac
Page 52 and 53: Patching ↓ To connect a pair of p
Page 54 and 55: Tip: Even if two patch points are c
Page 57 and 58: Introduction Features The IO Manage
Page 59 and 60: Adjusting Volumes ↓ To adjust the
Page 61 and 62: ↓ To set a digital output to prof
Page 63: ↓ To close a split window Summary
Page 66 and 67: THE SIMULATION TOOLS InsideTrak, Fa
Page 68 and 69: THE SIMULATION TOOLS • Angle chan
Page 70 and 71: Z THE SIMULATION TOOLS Figure 22
Page 74 and 75: Starting ↓ To access BinScape Edi
Page 76 and 77: Source name Primary location channe
Page 78 and 79: Custom Head Filter Specifications C
Page 80 and 81: Starting ↓ To access the Space Ar
Page 82 and 83: Removing an Object ↓ To remove th
Page 84 and 85: Placing the Observer ↓ To adjust
Page 86 and 87: Adding Room Reverberation ↓ To ad
Page 89 and 90: Features Operation AniScape The Ani
Page 91 and 92: Features Operation Starting The Sou
Page 93 and 94: Note: The first two elements in the
Page 95 and 96: Adding Room Reverberation ↓ To ad
Page 97 and 98: Features Operation Starting ↓ To
Page 99 and 100: Adding and Editing a Listener ↓ T
Page 101 and 102: Features Operation Starting The Bin
Page 103 and 104: Selecting and Changing a Head Relat
Page 105 and 106: Features Operation MultiScape The M
Page 107 and 108: Figure 36 — The MultiScape add so
Page 109 and 110: Figure 37 — MultiScape add speake
Page 111 and 112: Adding Editing and Removing Headpho
Page 113 and 114: Room Map Function ↓ To access the
Page 115 and 116: No Room simulation ↓ To select No
Page 117 and 118: Features Operation HeadScape HeadSc
Page 119 and 120: Figure 42 — HeadScape’s add ERT
Page 121 and 122: HURON1 3840 0.0 0 1.5 0 3.0 0 4.5 0
Page 123 and 124:
Features Operation Sonic Animator S
Page 125 and 126:
Starting ↓ To create a new scene
Page 127 and 128:
↓ To import a Locator script ↓
Page 129 and 130:
↓ To change a track’s propertie
Page 131:
External MTC Synchronisation ↓ Co
Page 135 and 136:
Features The Locator The Locator to
Page 137 and 138:
Moving a Listener Object or Sound O
Page 139:
↓ To record a Locator Script Summ
Page 142 and 143:
Hardware Connection ↓ Note: When
Page 144 and 145:
Starting ↓ To access WavePlayer-2
Page 146 and 147:
Optimising System Performance ↓ A
Page 148 and 149:
Starting ↓ To access the WavePlay
Page 151 and 152:
Features Make Room Make Room is a v
Page 153 and 154:
↓ To select an Output mode Select
Page 155 and 156:
↓ To set the sample rate ↓ To s
Page 157:
↓ To generate the impulse signals
Page 160 and 161:
Initialisation SNAP Commands Genera
Page 162 and 163:
AniScape Commands Parameter Descrip
Page 164 and 165:
OTHER SIMULATION TOOLS SNAPGetSourc
Page 166 and 167:
OTHER SIMULATION TOOLS SNAPMultiSet
Page 168 and 169:
OTHER SIMULATION TOOLS This command
Page 170 and 171:
OTHER SIMULATION TOOLS SNAPVMxGetIn
Page 172 and 173:
Parameter Description OTHER SIMULAT
Page 174 and 175:
WavePlayer Commands Parameter Descr
Page 176 and 177:
OTHER SIMULATION TOOLS in long lWav
Page 178 and 179:
Locator Commands General Commands S
Page 180 and 181:
Note: All doors should have at leas
Page 183:
Introduction to the Engineering Too
Page 186 and 187:
Figure 52 — Overview of the Convo
Page 188 and 189:
↓ To select the type of filter to
Page 190 and 191:
↓ To remove a FIR filter from the
Page 192 and 193:
Summary THE ENGINEERING TOOLS When
Page 194 and 195:
96kHz Filters Filter Type Number Fi
Page 197 and 198:
Introduction Features Operation The
Page 199 and 200:
Inputs ↓ To change the number of
Page 201 and 202:
Generating Test Signals ↓ To crea
Page 203:
Summary THE ENGINEERING TOOLS • T
Page 206 and 207:
THE ENGINEERING TOOLS • 1 96kHz D
Page 209:
Introduction to the SIM Tools The S
Page 212 and 213:
THE ENGINEERING TOOLS • Most Lake
Page 214 and 215:
THE ENGINEERING TOOLS Menu Item Con
Page 216 and 217:
↓ To convert or create a SIM file
Page 218 and 219:
↓ To display the magnitude of a c
Page 221:
Cutvec Windows Interface ↓ To sta
Page 224 and 225:
↓ To produce overlap ↓ To trans
Page 226 and 227:
↓ To generate a window function
Page 228 and 229:
↓ To generate a noise signal ↓
Page 230 and 231:
THE ENGINEERING TOOLS 6. Type the l
Page 232 and 233:
THE ENGINEERING TOOLS 6. Type the f
Page 234 and 235:
Figure 77 — The Plotwsim main int
Page 236 and 237:
↓ To set up a printer Note: The f
Page 238 and 239:
↓ To change the range of the X ax
Page 241 and 242:
Introduction Features Operation ↓
Page 243:
Usage Wavtosim Wavtosim is a comman
Page 247 and 248:
Introduction Uniform Window Bartlet
Page 249:
Blackman-Harris Window a( 0) = 0. 3
Page 253 and 254:
Features Applications Introduction
Page 255 and 256:
THE EQUALISATION TOOLS Menu Item Co
Page 257 and 258:
Loading EQ Canvasses ↓ To load a
Page 259 and 260:
↓ To move a Slider ↓ To adjust
Page 261 and 262:
↓ To select a filter length 1. Se
Page 263 and 264:
↓ To zoom into a section of canva
Page 265:
↓ To set Lake EQ to use Optimum P
Page 268 and 269:
96kHz Filters THE EQUALISATION TOOL
Page 271:
Other Tools This section introduces
Page 274 and 275:
Starting ↓ To access the VMixer
Page 276 and 277:
↓ To adjust the gain of an audio
Page 278 and 279:
Controlling VMixer Remotely Summary
Page 280 and 281:
↓ To select which pair of inputs
Page 282 and 283:
Altering the XYZ Balance ↓ To alt
Page 285 and 286:
Operation Starting ↓ To access I/
Page 287 and 288:
Testing Signal to Noise Ratios ↓
Page 289:
Huron Technical Reference The Huron
Page 292 and 293:
HURON TECHNICAL REFERENCE files tha
Page 295 and 296:
Huron Technical Specifications 16 B
Page 297 and 298:
Figure 101 — Frequency Response o
Page 299:
D-62 Connector Specifications HURON
Page 302 and 303:
HURON TECHNICAL REFERENCE • Alway
Page 304 and 305:
↓ To achieve the best results in
Page 306 and 307:
Binaural HRTF HURON TECHNICAL REFER
Page 308 and 309:
Linear Phase HURON TECHNICAL REFERE
Page 311 and 312:
VRack Autostart ↓ To auto-start V
show all

Huron & SNAP Documentation

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?