Huron & SNAP Documentation

More documents

Recommendations

Info

Figure 52 — Overview of the Convolver setup In general it can be stated that: THE ENGINEERING TOOLS • Each Convolver Setup, specified by the *.CLV file has a single filter type. • Each Convolver Setup may have from 1 to 512 Filter programs. • Each Filter program may have up 64 Filter Files (impulse responses, *.SIM). HURON TECHNICAL MANUAL PAGE 186
Operation Starting and Saving ↓ To access the Convolver Figure 53 — The Convolver interface THE ENGINEERING TOOLS The Convolver tool must be loaded into the VRack from the New/Engineering tools submenu under New in the VRack (for loading instructions refer to the System Tools section of this manual). • Click the Convolver in the rack panel. A setup file dialogue box will appear. Button Function New Creates an untitled Convolver setup file (*.CLV). Open … Opens a previously saved Convolver setup file (*.CLV). Save Saves the current Convolver setup file (*.CLV), If the document is untitled the software will prompt with a Save As dialogue box. Save As … Save the Convolver setup file (*.CLV) under a new name, the software will prompt with a Save As … dialogue box. Selecting the Filter Once a new Setup file has been invoked, the Convolver window expands to offer a choice of filters. HURON TECHNICAL MANUAL PAGE 187
Page 1:
Huron Technical Manual Software ver
Page 5:
Copyright © 1995-2003 Lake Technol
Page 9:
FCC Declaration (USA only) for Huro
Page 13 and 14:
Table of Contents DISCLAIMER.......
Page 15 and 16:
TABLE OF CONTENTS FEATURES ........
Page 17 and 18:
TABLE OF CONTENTS OPERATION .......
Page 19 and 20:
TABLE OF CONTENTS DC BLOCK.........
Page 21 and 22:
TABLE OF CONTENTS THE 96KHZ EQ ....
Page 23:
Introduction to the Huron Thank you
Page 26 and 27:
Features Applications Note: Any ISA
Page 28 and 29:
INTRODUCTION TO THE HURON • Optio
Page 30 and 31:
Installing New Hardware Components
Page 32 and 33:
↓ To change the ISA memory addres
Page 35 and 36:
↓ Connecting with the patch panel
Page 37 and 38:
Huron System Tools Huron Simulation
Page 39 and 40:
General Installation ↓ To install
Page 41:
Introduction to the System Tools Th
Page 44 and 45:
Operation Starting ↓ To start the
Page 46 and 47:
Configuration Functions Internal/Ex
Page 48 and 49:
Displaying, Hiding and Terminating
Page 50 and 51:
Stopping VRack ↓ To exit the VRac
Page 52 and 53:
Patching ↓ To connect a pair of p
Page 54 and 55:
Tip: Even if two patch points are c
Page 57 and 58:
Introduction Features The IO Manage
Page 59 and 60:
Adjusting Volumes ↓ To adjust the
Page 61 and 62:
↓ To set a digital output to prof
Page 63:
↓ To close a split window Summary
Page 66 and 67:
THE SIMULATION TOOLS InsideTrak, Fa
Page 68 and 69:
THE SIMULATION TOOLS • Angle chan
Page 70 and 71:
Z THE SIMULATION TOOLS Figure 22
Page 73 and 74:
Features Operation Object list Add
Page 75 and 76:
For example: if a Source Object (ch
Page 77 and 78:
Editing a BinScape Object ↓ To ed
Page 79 and 80:
Features Operation The Space Array
Page 81 and 82:
Adding an Object to the Space Array
Page 83 and 84:
Near Field Adding B-format Input Se
Page 85 and 86:
Inserting speakers ↓ To insert a
Page 87:
Summary 25 20 15 Number of inputs S
Page 90 and 91:
The simulated acoustic spaces used
Page 92 and 93:
↓ To access the Sound Field Filte
Page 94 and 95:
Directivity Factor Name d = 0.000 O
Page 96 and 97:
Setting Minimum Source Distance ↓
Page 98 and 99:
Adding, Inserting, Removing and Edi
Page 100 and 101:
DSP Usage Summary THE SIMULATION TO
Page 102 and 103:
↓ To access the Binaural Decoder
Page 104 and 105:
Summary THE SIMULATION TOOLS • Th
Page 106 and 107:
Starting ↓ To access MultiScape F
Page 108 and 109:
Editing a Sound Object ↓ To edit
Page 110 and 111:
B-format Decode Mode B-format Mode
Page 112 and 113:
Editing Headphone Objects ↓ To ed
Page 114 and 115:
Adding Rooms, Deleting Rooms Adding
Page 116 and 117:
Summary THE SIMULATION TOOLS • Mu
Page 118 and 119:
Starting ↓ To access HeadScape Se
Page 120 and 121:
Configuring HeadScape ↓ To config
Page 122 and 123:
Summary THE SIMULATION TOOLS • He
Page 124 and 125:
Scene (List of Tracks) Track (List
Page 126 and 127:
Figure 45 - Scene Properties dialog
Page 128 and 129:
Manipulating Tracks ↓ To add a tr
Page 130 and 131:
↓ Exporting a trajectory to a Loc
Page 133:
Other Simulation Tools This sub-sec
Page 136 and 137: Operation Starting ↓ To start the
Page 138 and 139: Locator Commands Loading and Playin
Page 141 and 142: Features Requirements The WavePlaye
Page 143 and 144: Figure 49 — The WavePlayer-2 inte
Page 145 and 146: ↓ Setting the RME Hammerfall as t
Page 147 and 148: Note: The Waveplayer has now been s
Page 149: Summary OTHER SIMULATION TOOLS •
Page 152 and 153: Operation Starting ↓ To start the
Page 154 and 155: ↓ To select a microphone setting
Page 156 and 157: ↓ To specify the Echo settings
Page 159 and 160: Integration under 32 bit Windows In
Page 161 and 162: Positional Commands Note: The numbe
Page 163 and 164: OTHER SIMULATION TOOLS SNAPGetRooms
Page 165 and 166: MultiScape Commands Parameter Descr
Page 167 and 168: Space Array Commands Parameter Desc
Page 169 and 170: VMixer Commands Parameter Descripti
Page 171 and 172: WavePlayer-2 Commands OTHER SIMULAT
Page 173 and 174: OTHER SIMULATION TOOLS SNAPWP2Pause
Page 175 and 176: OTHER SIMULATION TOOLS SNAPSetWaveH
Page 177 and 178: Command Reference This section desc
Page 179 and 180: WavePlayer Commands OTHER SIMULATIO
Page 181: TCP/IP Commands OTHER SIMULATION TO
Page 185: Introduction Features Overview of t
Page 189 and 190: ↓ To add a FIR filter to the Filt
Page 191 and 192: Currently selected patch point icon
Page 193 and 194: Introduction 96kHz Convolver Hardwa
Page 195: Patching the 96kHz Convolver Loadin
Page 198 and 199: Starting Note: If using measure to
Page 200 and 201: Selecting the Output File ↓ To se
Page 202 and 203: Signal Generation via MatLab Script
Page 205 and 206: Introduction 96kHz Measurement Tool
Page 207: Loading the 96kHz Measurement Tool
Page 211 and 212: ; comments ( (dtype [bit16 | bit20
Page 213 and 214: Introduction Operation Starting ↓
Page 215 and 216: Dfilter Windows Interface ↓ To st
Page 217 and 218: Lvec Windows Interface ↓ To start
Page 219: Padvec Windows Interface ↓ To sta
Page 223 and 224: Permute Windows Interface ↓ To st
Page 225 and 226: Wingen Windows Interface ↓ To sta
Page 227 and 228: SigGen Windows Interface ↓ To sta
Page 229 and 230: ↓ To generate a piecewise linear
Page 231 and 232: Vector Arithmetic Windows Interface
Page 233 and 234: Introduction Features Operation ↓
Page 235 and 236: Printing ↓ To print the SIM file
Page 237 and 238:
Altering the Axes ↓ To display sa
Page 239:
Summary THE ENGINEERING TOOLS • P
Page 242 and 243:
Note: In this version of SimScale i
Page 245:
Usage Simtowav Simtowav is a comman
Page 248 and 249:
Hamming Window Blackman Window Harr
Page 251:
Introduction to the Programming Too
Page 254 and 255:
Operation Starting Lake EQ ↓ To a
Page 256 and 257:
Slider Widget Toolbar Creating an E
Page 258 and 259:
High Shelf Tip: All the sliders can
Page 260 and 261:
Calculating the Equalisation Curve
Page 262 and 263:
↓ To lock a Slider ↓ To unlock
Page 264 and 265:
Limits ↓ To alter the graph limit
Page 267 and 268:
Introduction 96kHz EQ Hardware Requ
Page 269:
Loading EQ 96kHz THE EQUALISATION T
Page 273 and 274:
Features Operation The VMixer The V
Page 275 and 276:
Note: When increasing the size of V
Page 277 and 278:
Muting ↓ To mute all output chann
Page 279 and 280:
Operation Starting ↓ To access th
Page 281 and 282:
Operation Starting ↓ To access th
Page 283:
Summary OTHER TOOLS • The BFormat
Page 286 and 287:
I/O Test Patching Selecting the For
Page 288 and 289:
Summary • To utilise I/O Test an
Page 291 and 292:
Fixed Point Digital Audio Data Repr
Page 293:
↓ SimScale Avoiding Large Frequen
Page 296 and 297:
Figure 99 — SNR of the 16 bit A/D
Page 298 and 299:
Mechanical Specifications 1 3 Figur
Page 301 and 302:
Audio Input Levels Managing Audio S
Page 303 and 304:
HURON TECHNICAL REFERENCE • In ge
Page 305 and 306:
Angle Channels Glossary Angle chann
Page 307 and 308:
Order of Reflections HURON TECHNICA
Page 309:
SNR (Signal to Noise Ratio) HURON T
Page 312:
↓ To specify an auto-logon domain
show all

Huron & SNAP Documentation

Create successful ePaper yourself

Delete template?

Save as template?