SFCD: Federal Commander Digital System - Federal Signal
SFCD: Federal Commander Digital System - Federal Signal SFCD: Federal Commander Digital System - Federal Signal
Destination Federal Commander Digital System The destination list contains the currently selected sites and zones. To add sites highlight the desired sites and zones to sound and click the Add button. Any number and combination of individual sites and zones may be added. To select all sites in your system click the Add All button. “All Sirens” will be added to the destination list and all other selections will be removed. “All Sirens” must be removed before Individual Sites or Zones may be added. To remove sites click the remove or Remove All button. Function The Function list box displays the function to be sounded. To change this selection, click on the control and select the desired function from the dropdown list. PA Wave File PA SmartMsg „PA SmartMsg‟ and „PA Wave File‟ are special functions for streaming audio to the RTU as public address. „PA SmartMsg‟ converts the SmartMsg text to audio using text to speech (TTS). „PA Wave File‟ plays a previously recorded wav file. When „PA Wave File‟ is selected the Windows® browse dialog will appear. The selected filename will appear below the Function setting: 92 Activate
Federal Commander Digital System „PA Wave File‟ and „PA Smartmsg‟ only function on channels programmed for Codespear mode or Modem mode using the Federal Signal MSK Modem (2005249). Do not use these functions on channels programmed for SS2000. When using Modem mode with the MSK Modem, program #1 of the UltraVoice must be programmed as: ARM PA OUTPUT DISARM Auto-Poll after Activation If this box is checked SFCDWARE will poll each site after an approximately 30 second delay. Repeat All Call 3 times Check this option to enable all call repeats. The delay between repeats is configured using the “Retry Delay” parameter on the System setup screen. Note: This setting overrides the “Repeat All Call 3 times” setting on the System setup screen. Dynamic Digital Voice The Dynamic Digital Voice list displays a list of digital voice messages to be played back during the DYNAMIC VOICE function. Messages are annunciated in sequence, starting with the first message in the list and ending with the last. Up to a maximum of 20 messages may be programmed. If dynamic voice is not used, this list may be left blank. To add a message click the add button and select the desired message from the dropdown list. The message will be placed just under the currently selected message. To delete a message, double click on the message. 93 Activate
- Page 41 and 42: Federal Commander Digital System va
- Page 43 and 44: SFCDWARE Main Screen Federal Comman
- Page 45 and 46: Help Federal Commander Digital Syst
- Page 47 and 48: Tools Menu Federal Commander Digita
- Page 49 and 50: System Configuration Federal Comman
- Page 51 and 52: Update User Federal Commander Digit
- Page 53 and 54: Quit Federal Commander Digital Syst
- Page 55 and 56: Message Templates Federal Commander
- Page 57 and 58: Quit Federal Commander Digital Syst
- Page 59 and 60: acknowledged. Federal Commander Dig
- Page 61 and 62: Reports Federal Commander Digital S
- Page 63 and 64: Export Federal Commander Digital Sy
- Page 65 and 66: AVAILABLE RADIO BUTTON SELECTIONS D
- Page 67 and 68: Print Report Federal Commander Digi
- Page 69 and 70: Federal Commander Digital System di
- Page 71 and 72: Legend Federal Commander Digital Sy
- Page 73 and 74: Federal Commander Digital System To
- Page 75 and 76: Federal Commander Digital System To
- Page 77 and 78: Federal Commander Digital System Pr
- Page 79 and 80: Federal Commander Digital System Hi
- Page 81 and 82: The following warning will be displ
- Page 83 and 84: Button Number Federal Commander Dig
- Page 85 and 86: PA Wave File PA SmartMsg Federal Co
- Page 87 and 88: Templates Federal Commander Digital
- Page 89 and 90: Length: Display Tab Federal Command
- Page 91: Send Federal Commander Digital Syst
- Page 95 and 96: Federal Commander Digital System Th
- Page 97 and 98: Mode Federal Commander Digital Syst
- Page 99 and 100: System Setup Federal Commander Digi
- Page 101 and 102: Federal Commander Digital System To
- Page 103 and 104: Federal Commander Digital System Th
- Page 105 and 106: Federal Commander Digital System in
- Page 107 and 108: Federal Commander Digital System ad
- Page 109 and 110: Federal Commander Digital System ot
- Page 111 and 112: Federal Commander Digital System Th
- Page 113 and 114: Federal Commander Digital System ac
- Page 115 and 116: Voice Modem Comm Port Federal Comma
- Page 117 and 118: Save Federal Commander Digital Syst
- Page 119 and 120: Federal Commander Digital System
- Page 121 and 122: Federal Commander Digital System Th
- Page 123 and 124: Introduction Federal Commander Digi
- Page 125 and 126: Federal Commander Digital System Nu
- Page 127 and 128: IO Board Federal Commander Digital
- Page 129 and 130: RTU Federal Commander Digital Syste
- Page 131 and 132: Quit Federal Commander Digital Syst
- Page 133 and 134: Front Porch Federal Commander Digit
- Page 135 and 136: Federal Commander Digital System re
- Page 137 and 138: Federal Commander Digital System Al
- Page 139 and 140: Correct the problem and Save again.
- Page 141 and 142: DELAY REPEAT START POWER DIGITAL VO
<strong>Federal</strong> <strong>Commander</strong> <strong>Digital</strong> <strong>System</strong><br />
„PA Wave File‟ and „PA Smartmsg‟ only function on channels programmed for Codespear mode<br />
or Modem mode using the <strong>Federal</strong> <strong>Signal</strong> MSK Modem (2005249). Do not use these functions on<br />
channels programmed for SS2000. When using Modem mode with the MSK Modem, program #1<br />
of the UltraVoice must be programmed as:<br />
ARM<br />
PA OUTPUT<br />
DISARM<br />
Auto-Poll after Activation<br />
If this box is checked <strong>SFCD</strong>WARE will poll each site after an approximately 30 second delay.<br />
Repeat All Call 3 times<br />
Check this option to enable all call repeats. The delay between repeats is configured using the<br />
“Retry Delay” parameter on the <strong>System</strong> setup screen. Note: This setting overrides the “Repeat<br />
All Call 3 times” setting on the <strong>System</strong> setup screen.<br />
Dynamic <strong>Digital</strong> Voice<br />
The Dynamic <strong>Digital</strong> Voice list displays a list of digital voice messages to be played back during<br />
the DYNAMIC VOICE function. Messages are annunciated in sequence, starting with the first<br />
message in the list and ending with the last. Up to a maximum of 20 messages may be<br />
programmed. If dynamic voice is not used, this list may be left blank.<br />
To add a message click the add button and select the desired message from the dropdown list.<br />
The message will be placed just under the currently selected message. To delete a message,<br />
double click on the message.<br />
93<br />
Activate