SFCD: Federal Commander Digital System - Federal Signal
SFCD: Federal Commander Digital System - Federal Signal SFCD: Federal Commander Digital System - Federal Signal
The InstaCal program will start: Federal Commander Digital System After a few seconds InstaCal will automatically detect your PCI-PDISO8 IO Board and display the following dialog: 36 Installation
Federal Commander Digital System Click OK and close the InstaCal program. Your IO Board is not configured and ready to use. It is not necessary to run InstaCal again unless the IO Board hardware is reinstalled. For making connections to the IO Board reference “Making Connections to the IO Card” section of this document. Digital Inputs and Relay Outputs may be assigned to hotkeys and configured using the IO Board dialog accessed from the System Setup menu. AT&T Natural Voices Speech Font (Optional) If the system will be using the Text-to-Speech option, the AT&T Natural Voices speech font must be installed. INTRODUCTION: The AT&T Natural Voices software converts text to a high quality natural sounding voice for use with the Federal Commander Mass Alert and Notification software. Mike16 is the default voice provided with the installation. Optionally, a female voice font (Crystal16) may also be used. Contact your local Federal Signal Sales Representative if a female voice font is required for your application. INSTALLATION: 1. Insert the installation CD into the CD-ROM drive. 2. Click “Start-My Computer” and select the CD ROM. 3. Locate the setup.exe on the CD ROM. 4. Click “Setup.exe” to launch the runtime installation program. Answer all prompts without changing the default settings. 5. After the Runtime installation has successfully completed, bring up the Windows Control Panel and select the “Speech” icon. The following dialog box will appear: 37 Installation
- Page 1 and 2: Federal Commander Digital System Th
- Page 3 and 4: Federal Commander Digital System Lo
- Page 5 and 6: Federal Commander Digital System Se
- Page 7 and 8: Federal Commander Digital System IP
- Page 9 and 10: Federal Commander Digital System St
- Page 11 and 12: Federal Commander Digital System Se
- Page 13 and 14: Federal Commander Digital System Li
- Page 15 and 16: Federal Commander Digital System NO
- Page 17 and 18: Federal Commander Digital System In
- Page 19 and 20: Federal Commander Digital System CC
- Page 21 and 22: MODEM-MSK Description Federal Comma
- Page 23 and 24: Federal Commander Digital System De
- Page 25 and 26: Federal Commander Digital System Wo
- Page 27 and 28: Codespear Federal Commander Digital
- Page 29 and 30: MAPPING.DAT: Federal Commander Digi
- Page 31 and 32: Federal Commander Digital System Co
- Page 33 and 34: Federal Commander Digital System 3.
- Page 35: Federal Commander Digital System 1.
- Page 39 and 40: Federal Commander Digital System 7.
- Page 41 and 42: Federal Commander Digital System va
- Page 43 and 44: SFCDWARE Main Screen Federal Comman
- Page 45 and 46: Help Federal Commander Digital Syst
- Page 47 and 48: Tools Menu Federal Commander Digita
- Page 49 and 50: System Configuration Federal Comman
- Page 51 and 52: Update User Federal Commander Digit
- Page 53 and 54: Quit Federal Commander Digital Syst
- Page 55 and 56: Message Templates Federal Commander
- Page 57 and 58: Quit Federal Commander Digital Syst
- Page 59 and 60: acknowledged. Federal Commander Dig
- Page 61 and 62: Reports Federal Commander Digital S
- Page 63 and 64: Export Federal Commander Digital Sy
- Page 65 and 66: AVAILABLE RADIO BUTTON SELECTIONS D
- Page 67 and 68: Print Report Federal Commander Digi
- Page 69 and 70: Federal Commander Digital System di
- Page 71 and 72: Legend Federal Commander Digital Sy
- Page 73 and 74: Federal Commander Digital System To
- Page 75 and 76: Federal Commander Digital System To
- Page 77 and 78: Federal Commander Digital System Pr
- Page 79 and 80: Federal Commander Digital System Hi
- Page 81 and 82: The following warning will be displ
- Page 83 and 84: Button Number Federal Commander Dig
- Page 85 and 86: PA Wave File PA SmartMsg Federal Co
<strong>Federal</strong> <strong>Commander</strong> <strong>Digital</strong> <strong>System</strong><br />
Click OK and close the InstaCal program. Your IO Board is not configured and ready to use. It is<br />
not necessary to run InstaCal again unless the IO Board hardware is reinstalled.<br />
For making connections to the IO Board reference “Making Connections to the IO Card” section<br />
of this document. <strong>Digital</strong> Inputs and Relay Outputs may be assigned to hotkeys and configured<br />
using the IO Board dialog accessed from the <strong>System</strong> Setup menu.<br />
AT&T Natural Voices Speech Font (Optional)<br />
If the system will be using the Text-to-Speech option, the AT&T Natural Voices speech font must<br />
be installed.<br />
INTRODUCTION:<br />
The AT&T Natural Voices software converts text to a high quality natural sounding voice for use<br />
with the <strong>Federal</strong> <strong>Commander</strong> Mass Alert and Notification software. Mike16 is the default voice<br />
provided with the installation. Optionally, a female voice font (Crystal16) may also be used.<br />
Contact your local <strong>Federal</strong> <strong>Signal</strong> Sales Representative if a female voice font is required for your<br />
application.<br />
INSTALLATION:<br />
1. Insert the installation CD into the CD-ROM drive.<br />
2. Click “Start-My Computer” and select the CD ROM.<br />
3. Locate the setup.exe on the CD ROM.<br />
4. Click “Setup.exe” to launch the runtime installation program. Answer all prompts without<br />
changing the default settings.<br />
5. After the Runtime installation has successfully completed, bring up the Windows Control<br />
Panel and select the “Speech” icon. The following dialog box will appear:<br />
37<br />
Installation