SFCD: Federal Commander Digital System - Federal Signal
Share Embed Flag
Download ePaper

SFCD: Federal Commander Digital System - Federal Signal

SFCD: Federal Commander Digital System - Federal Signal SFCD: Federal Commander Digital System - Federal Signal

federalsignal.indust.com
from federalsignal.indust.com More from this publisher
05.05.2013 Views

HI POWER MODE Return unit to full power. QUIET TEST Federal Commander Digital System Performs a self-test of the siren control unit, amplifiers and speakers by sounding a 20KHZ tone. DELAY Delay or pause for a fixed number of seconds. AMP/AUDIO ZONE Allows amplifiers and audio outputs (audio relay board) to be selectively disabled for zoning purposes. POWER Allows the siren output power to be reduced by a selectable amount. RECORD PA Records live PA message for later playback utilizing the “PLAY RECORDED PA” function. Recording is terminated by reception of the EAS-SAME End of Message command or two minutes, whichever occurs first. REPEAT START REPEAT END Repeat Start and Repeat End are used to frame a sequence of functions for repeating. Example: The following program will repeat the DIGITAL VOICE-1 and DITIAL VOICE-2 sequence three times. 142 RTU

Activation Functions: PA OUTPUT Federal Commander Digital System Broadcast live radio PA. PA will remain active until carrier has dropped for ten seconds or 4 1/2 minutes, whichever occurs first. WAIL Sound Wail siren tone. PULSED WAIL Sound Pulsed Wail siren tone. ALT WAIL Sound Alternate Wail siren tone. STEADY Sound Steady siren tone. PULSED STEADY Sound Pulsed Steady siren tone. ALT STEADY Sound Alternate Steady siren tone. AUXILIARY Sound Auxiliary siren tone. The Auxiliary tone is normally set for Westminster Chimes. DIGITAL VOICE -n Play Digital Voice number n. Range: 1 – 16 (for Legacy RTUs) 1 – 250 (for RTUs running uvh v7.2 or greater) Warning: Do not attempt to play digital voice number greater than 16 on legacy RTUs. PLAY RECORDED PA Play message previously recorded during the “RECORD PA” function. For EAS activation, the message will repeat continuously for the duration of time encoded in the TTTT field. For non- EAS activation, the “PLAY RECORDED PA” function will play once without repeats. DYNAMIC VOICE Plays a sequence of digital voice messages specified at the time of activation. This function is only applicable for sirens equipped with a special vocabulary chip. 143 RTU

HI POWER MODE<br />

Return unit to full power.<br />

QUIET TEST<br />

<strong>Federal</strong> <strong>Commander</strong> <strong>Digital</strong> <strong>System</strong><br />

Performs a self-test of the siren control unit, amplifiers and speakers by sounding a 20KHZ tone.<br />

DELAY<br />

Delay or pause for a fixed number of seconds.<br />

AMP/AUDIO ZONE<br />

Allows amplifiers and audio outputs (audio relay board) to be selectively disabled for zoning<br />

purposes.<br />

POWER<br />

Allows the siren output power to be reduced by a selectable amount.<br />

RECORD PA<br />

Records live PA message for later playback utilizing the “PLAY RECORDED PA” function.<br />

Recording is terminated by reception of the EAS-SAME End of Message command or two<br />

minutes, whichever occurs first.<br />

REPEAT START<br />

REPEAT END<br />

Repeat Start and Repeat End are used to frame a sequence of functions for repeating.<br />

Example: The following program will repeat the DIGITAL VOICE-1 and DITIAL VOICE-2<br />

sequence three times.<br />

142<br />

RTU

logo

products

Resources

Company

Terms of service
Privacy policy
Cookie policy
Cookie settings
Imprint
Change language
Made with love in Switzerland
© 2024 Yumpu.com all rights reserved

Hooray! Your file is uploaded and ready to be published.

Saved successfully!

Ooh no, something went wrong!