SFCD: Federal Commander Digital System - Federal Signal
SFCD: Federal Commander Digital System - Federal Signal SFCD: Federal Commander Digital System - Federal Signal
DTMF (optional) Federal Commander Digital System If this is a DTMF type code, enter the DTMF digits for this function here. Acceptable DTMF digits are: 0-9, A, B, C, D, *, #. Note: The DTMF selection is only applicable on systems that use DTMF signaling. Duotone (optional) If this is a tone type code, enter the A Tone and B Tone frequencies for this function here. The acceptable frequency range is 280-3000 Hz. Note: The duotone selection is only applicable on systems that use duotone signaling. EAS Event (optional) For units using EAS/SAME decoding, allows an EAS Event (EEE) code to be associated with this activation function. For EAS activation, the following two conditions must be valid: 1. The location code of the transmitted EAS message matches one of the three programmed location codes (see Config RTU). 2. The EVENT code of the transmitted EAS message matches an event code assigned to an activation code. Note: EAS and Duotone activation is mutually exclusive. For EAS activation to be functional, the Duotone Timing parameters (A-Time, B-Time, S-Time) must be set to zero. Function Two list boxes handle setting up the function sequence. The Function Select box contains a list of available functions. To add a function highlight the desired function and click the Add->> button. The new function will be inserted after the selected (highlighted) item in the Function box. Functions will be executed in sequence and in the order they appear in the list. To remove a function highlight the desired function and click the Remove button. Click Remove All to remove all functions. Arm and Function timers All sounding functions and relays outputs will automatically turn off when the RTU becomes disarmed. Upon reception of the ARM function the RTU will remain armed for 255 seconds. The disarm timer is halted during sounding functions and resumes during the DELAY function or at the end of the function sequence. It is good practice to start each function sequence with an ARM and end with a DISARM. Each individual function is limited to 255 seconds duration. The following functions consume two slots: 140 RTU
DELAY REPEAT START POWER DIGITAL VOICE-n (only if n > 16) The following function consumes three slots: Federal Commander Digital System AMP/AUDIO ZONE All other functions consume one of the 20 available slots. Available Functions Utility Functions: ARM Arms the siren. The siren must be armed or activation functions will not operate. Once armed, the siren will remain armed for approximately 4 ½ minutes. The ARM function will also perform the following: 1. Set Phasing to off (PHASE OFF). 2. Set power output to maximum (HIGH POWER MODE) 3. Set amp zoning to all amps enabled. DISARM Disarms the siren REPORT Send unit status to base. MASTER RESET Terminates active function and clears latched status. PLUS PHASE All functions between “PLUS PHASE” and “MINUS PHASE” will repeat for the duration of time encoded in the EAS activation frame (EAS activations only). MINUS PHASE All functions between “PLUS PHASE” and “MINUS PHASE” will repeat for the duration of time encoded in the EAS activation frame (EAS activations only). PHASE OFF Turn off minus and plus phase and return siren to omni directional mode. LOW POWER MODE Reduce unit power to approximately one watt. 141 RTU
- Page 89 and 90: Length: Display Tab Federal Command
- Page 91 and 92: Send Federal Commander Digital Syst
- Page 93 and 94: Federal Commander Digital System
- Page 95 and 96: Federal Commander Digital System Th
- Page 97 and 98: Mode Federal Commander Digital Syst
- Page 99 and 100: System Setup Federal Commander Digi
- Page 101 and 102: Federal Commander Digital System To
- Page 103 and 104: Federal Commander Digital System Th
- Page 105 and 106: Federal Commander Digital System in
- Page 107 and 108: Federal Commander Digital System ad
- Page 109 and 110: Federal Commander Digital System ot
- Page 111 and 112: Federal Commander Digital System Th
- Page 113 and 114: Federal Commander Digital System ac
- Page 115 and 116: Voice Modem Comm Port Federal Comma
- Page 117 and 118: Save Federal Commander Digital Syst
- Page 119 and 120: Federal Commander Digital System
- Page 121 and 122: Federal Commander Digital System Th
- Page 123 and 124: Introduction Federal Commander Digi
- Page 125 and 126: Federal Commander Digital System Nu
- Page 127 and 128: IO Board Federal Commander Digital
- Page 129 and 130: RTU Federal Commander Digital Syste
- Page 131 and 132: Quit Federal Commander Digital Syst
- Page 133 and 134: Front Porch Federal Commander Digit
- Page 135 and 136: Federal Commander Digital System re
- Page 137 and 138: Federal Commander Digital System Al
- Page 139: Correct the problem and Save again.
- Page 143 and 144: Activation Functions: PA OUTPUT Fed
- Page 145 and 146: RELAY #4 OFF Federal Commander Digi
- Page 147 and 148: Federal Commander Digital System Th
- Page 149 and 150: Federal Commander Digital System Fo
- Page 151 and 152: Delete Message: Delete All RTU butt
- Page 153 and 154: Poll This RTU Federal Commander Dig
- Page 155 and 156: Federal Commander Digital System Th
- Page 157 and 158: Federal Commander Digital System Di
- Page 159 and 160: Voltage Federal Commander Digital S
- Page 161 and 162: Notepad Federal Commander Digital S
- Page 163 and 164: displayed. Last Function RTU Federa
- Page 165 and 166: Name Column Federal Commander Digit
- Page 167 and 168: Record Checkbox Federal Commander D
- Page 169 and 170: Federal Commander Digital System Co
- Page 171 and 172: Federal Commander Digital System Th
- Page 173 and 174: Federal Commander Digital System 17
- Page 175 and 176: Federal Commander Digital System 17
- Page 177 and 178: Federal Commander Digital System 3.
- Page 179 and 180: Federal Commander Digital System 11
- Page 181: Federal Commander Digital System 3.
DELAY<br />
REPEAT START<br />
POWER<br />
DIGITAL VOICE-n (only if n > 16)<br />
The following function consumes three slots:<br />
<strong>Federal</strong> <strong>Commander</strong> <strong>Digital</strong> <strong>System</strong><br />
AMP/AUDIO ZONE<br />
All other functions consume one of the 20 available slots.<br />
Available Functions<br />
Utility Functions:<br />
ARM<br />
Arms the siren. The siren must be armed or activation functions will not operate. Once armed,<br />
the siren will remain armed for approximately 4 ½ minutes. The ARM function will also perform<br />
the following:<br />
1. Set Phasing to off (PHASE OFF).<br />
2. Set power output to maximum (HIGH POWER MODE)<br />
3. Set amp zoning to all amps enabled.<br />
DISARM<br />
Disarms the siren<br />
REPORT<br />
Send unit status to base.<br />
MASTER RESET<br />
Terminates active function and clears latched status.<br />
PLUS PHASE<br />
All functions between “PLUS PHASE” and “MINUS PHASE” will repeat for the duration of time<br />
encoded in the EAS activation frame (EAS activations only).<br />
MINUS PHASE<br />
All functions between “PLUS PHASE” and “MINUS PHASE” will repeat for the duration of time<br />
encoded in the EAS activation frame (EAS activations only).<br />
PHASE OFF<br />
Turn off minus and plus phase and return siren to omni directional mode.<br />
LOW POWER MODE<br />
Reduce unit power to approximately one watt.<br />
141<br />
RTU