SFCD: Federal Commander Digital System - Federal Signal
SFCD: Federal Commander Digital System - Federal Signal SFCD: Federal Commander Digital System - Federal Signal
Federal Commander Digital System The System Log frame allows the ability to map system log messages to a group of users. When the selected event occurs, a SmartMsg will be sent to the group of users selected. Up to ten user groups may be configured. Note: Use caution when selecting messages that may have a high incidence of occurrence. Message Filter Use the message filter to select which system log messages will be sent to the respective SmartMsg group. Resend alarm notifications each time alarm condition is reported Select this option if it is desired to SmartMsg RTU alarms each time an alarm condition is reported. RTU alarms are reported each polling cycle. Do not repeat notification for existing alarms Select this option to SmartMsg only new alarms. This will prevent notification of the same alarm each time the system is polled. System Fail Introduction System Fail is a user configurable status point. The user determines the conditions which constitute a System Fail using the System Fail Setup dialog, available from the Status Base screen. System fail is comprised of two components: Individual System Fail. General System Fail. Individual System Fail is reported on the Status Detail screen for each site in the system. This status point is set to fail when the conditions setup on the Alarm Filter is met following reception of a poll response. An individual system fail does not cause an entry in the system log or start a callout or email process. A general System Fail occurs when the number of individual sites with System Fail exceeds the number setup in the “Number of failed sites constitutes System Fail” parameter. At this time, a “System Fail” entry will be posted to the System Log and if enabled, callout and email will occur. Callout and Email use the same callout list and email parameters as other alarms (standard software). The system checks for a general system fail once a minute by scanning individual sites. Once a general system fail occurs, all individual system fails are cleared. A general system failure will occur the next time the number of failed individual sites equals or exceeds the configured value. This will normally occur following the next system polling. System fail setup dialog Clicking on the System Fail button displays the System Fail setup dialog: 124 System Setup
Federal Commander Digital System Number of failed sites constitutes System Fail Set the number of failed sites constitutes System Fail value in the numeric text box. Use the updown arrows or the number may be entered directly. When the number of individual sites with System Fail as defined using the Alarm Filter below exceeds or exceeds this value, a System Fail alarm will be reported. Callout on System Fail Set this checkbox to have SFCDWARE initiate a callout sequence when a System Fail alarm occurs. Alarm Filter Use the Alarm Filter to define which alarms constitute system fail. % Amps Fail 125 System Setup
- Page 73 and 74: Federal Commander Digital System To
- Page 75 and 76: Federal Commander Digital System To
- Page 77 and 78: Federal Commander Digital System Pr
- Page 79 and 80: Federal Commander Digital System Hi
- Page 81 and 82: The following warning will be displ
- Page 83 and 84: Button Number Federal Commander Dig
- Page 85 and 86: PA Wave File PA SmartMsg Federal Co
- Page 87 and 88: Templates Federal Commander Digital
- Page 89 and 90: Length: Display Tab Federal Command
- Page 91 and 92: Send Federal Commander Digital Syst
- Page 93 and 94: Federal Commander Digital System
- Page 95 and 96: Federal Commander Digital System Th
- Page 97 and 98: Mode Federal Commander Digital Syst
- Page 99 and 100: System Setup Federal Commander Digi
- Page 101 and 102: Federal Commander Digital System To
- Page 103 and 104: Federal Commander Digital System Th
- Page 105 and 106: Federal Commander Digital System in
- Page 107 and 108: Federal Commander Digital System ad
- Page 109 and 110: Federal Commander Digital System ot
- Page 111 and 112: Federal Commander Digital System Th
- Page 113 and 114: Federal Commander Digital System ac
- Page 115 and 116: Voice Modem Comm Port Federal Comma
- Page 117 and 118: Save Federal Commander Digital Syst
- Page 119 and 120: Federal Commander Digital System
- Page 121 and 122: Federal Commander Digital System Th
- Page 123: Introduction Federal Commander Digi
- Page 127 and 128: IO Board Federal Commander Digital
- Page 129 and 130: RTU Federal Commander Digital Syste
- Page 131 and 132: Quit Federal Commander Digital Syst
- Page 133 and 134: Front Porch Federal Commander Digit
- Page 135 and 136: Federal Commander Digital System re
- Page 137 and 138: Federal Commander Digital System Al
- Page 139 and 140: Correct the problem and Save again.
- Page 141 and 142: DELAY REPEAT START POWER DIGITAL VO
- Page 143 and 144: Activation Functions: PA OUTPUT Fed
- Page 145 and 146: RELAY #4 OFF Federal Commander Digi
- Page 147 and 148: Federal Commander Digital System Th
- Page 149 and 150: Federal Commander Digital System Fo
- Page 151 and 152: Delete Message: Delete All RTU butt
- Page 153 and 154: Poll This RTU Federal Commander Dig
- Page 155 and 156: Federal Commander Digital System Th
- Page 157 and 158: Federal Commander Digital System Di
- Page 159 and 160: Voltage Federal Commander Digital S
- Page 161 and 162: Notepad Federal Commander Digital S
- Page 163 and 164: displayed. Last Function RTU Federa
- Page 165 and 166: Name Column Federal Commander Digit
- Page 167 and 168: Record Checkbox Federal Commander D
- Page 169 and 170: Federal Commander Digital System Co
- Page 171 and 172: Federal Commander Digital System Th
- Page 173 and 174: Federal Commander Digital System 17
<strong>Federal</strong> <strong>Commander</strong> <strong>Digital</strong> <strong>System</strong><br />
Number of failed sites constitutes <strong>System</strong> Fail<br />
Set the number of failed sites constitutes <strong>System</strong> Fail value in the numeric text box. Use the updown<br />
arrows or the number may be entered directly. When the number of individual sites with<br />
<strong>System</strong> Fail as defined using the Alarm Filter below exceeds or exceeds this value, a <strong>System</strong> Fail<br />
alarm will be reported.<br />
Callout on <strong>System</strong> Fail<br />
Set this checkbox to have <strong>SFCD</strong>WARE initiate a callout sequence when a <strong>System</strong> Fail alarm<br />
occurs.<br />
Alarm Filter<br />
Use the Alarm Filter to define which alarms constitute system fail.<br />
% Amps Fail<br />
125<br />
<strong>System</strong> Setup