SFCD: Federal Commander Digital System - Federal Signal
SFCD: Federal Commander Digital System - Federal Signal SFCD: Federal Commander Digital System - Federal Signal
Available Functions: Federal Commander Digital System Standard RTU functions (1 – 50, Master Reset, Quiet Test, Cancel) PA Wav File Hotkeys The standard RTU functions execute the selected function as programmed at the RTU. „PA Wave File” streams a wave file to the siren as public address. Hotkey functions perform the function programmed under an activation hotkey, including encode and SmartMsg if applicable. When Hotkey is selected the site selection controls are ignored (RTU or Zone Number). The site selection is obtained from the hotkey programming. PA Wave File „PA Wave File‟ is a special function for streaming audio to the RTU as public address. When „PA Wave File‟ is selected the Windows® browse dialog will appear. The selected filename will appear to the right of the Function control: 118 System Setup
Federal Commander Digital System „PA Wave File‟ and „PA Smartmsg‟ only function on channels programmed for Codespear mode or Modem mode using the Federal Signal MSK Modem (2005249). Do not use these functions on channels programmed for SS2000. When using Modem mode with the MSK Modem, program #1 of the UltraVoice must be programmed as: ARM PA OUTPUT DISARM Holiday Function The Holiday Function will override the normal function on selected holiday dates. See Holiday Time below. RTU or Zone Number This field selects which RTU(s) will sound for the respective alarm. To change selection, click on the desired radio button (Individual, Zone or All Call). For Individual and zone modes, enter the desired site or zone number in the Textbox provided. When Hotkey is selectedfor the Function or Holiday Function, these site selection controls are ignored. The site selection is obtained from the hotkey programming. Individual Only RTU number selected will sound for respective alarm. Zone RTUs in selected zone will sound for respective alarm. All Call All RTUs will sound for respective alarm. Mode The three radio buttons Disabled, Daily, and Weekly select the mode of operation for each respective alarm. To change this setting, click on the desired radio button. This selection is mutually exclusive and only one mode may be selected. For Weekly mode, the desired days of the week and week number must be selected. Disabled This alarm is not active and will not occur at any time. 119 System Setup
- Page 67 and 68: Print Report Federal Commander Digi
- Page 69 and 70: Federal Commander Digital System di
- Page 71 and 72: Legend Federal Commander Digital Sy
- Page 73 and 74: Federal Commander Digital System To
- Page 75 and 76: Federal Commander Digital System To
- Page 77 and 78: Federal Commander Digital System Pr
- Page 79 and 80: Federal Commander Digital System Hi
- Page 81 and 82: The following warning will be displ
- Page 83 and 84: Button Number Federal Commander Dig
- Page 85 and 86: PA Wave File PA SmartMsg Federal Co
- Page 87 and 88: Templates Federal Commander Digital
- Page 89 and 90: Length: Display Tab Federal Command
- Page 91 and 92: Send Federal Commander Digital Syst
- Page 93 and 94: Federal Commander Digital System
- Page 95 and 96: Federal Commander Digital System Th
- Page 97 and 98: Mode Federal Commander Digital Syst
- Page 99 and 100: System Setup Federal Commander Digi
- Page 101 and 102: Federal Commander Digital System To
- Page 103 and 104: Federal Commander Digital System Th
- Page 105 and 106: Federal Commander Digital System in
- Page 107 and 108: Federal Commander Digital System ad
- Page 109 and 110: Federal Commander Digital System ot
- Page 111 and 112: Federal Commander Digital System Th
- Page 113 and 114: Federal Commander Digital System ac
- Page 115 and 116: Voice Modem Comm Port Federal Comma
- Page 117: Save Federal Commander Digital Syst
- Page 121 and 122: Federal Commander Digital System Th
- Page 123 and 124: Introduction Federal Commander Digi
- Page 125 and 126: Federal Commander Digital System Nu
- Page 127 and 128: IO Board Federal Commander Digital
- Page 129 and 130: RTU Federal Commander Digital Syste
- Page 131 and 132: Quit Federal Commander Digital Syst
- Page 133 and 134: Front Porch Federal Commander Digit
- Page 135 and 136: Federal Commander Digital System re
- Page 137 and 138: Federal Commander Digital System Al
- Page 139 and 140: Correct the problem and Save again.
- Page 141 and 142: DELAY REPEAT START POWER DIGITAL VO
- Page 143 and 144: Activation Functions: PA OUTPUT Fed
- Page 145 and 146: RELAY #4 OFF Federal Commander Digi
- Page 147 and 148: Federal Commander Digital System Th
- Page 149 and 150: Federal Commander Digital System Fo
- Page 151 and 152: Delete Message: Delete All RTU butt
- Page 153 and 154: Poll This RTU Federal Commander Dig
- Page 155 and 156: Federal Commander Digital System Th
- Page 157 and 158: Federal Commander Digital System Di
- Page 159 and 160: Voltage Federal Commander Digital S
- Page 161 and 162: Notepad Federal Commander Digital S
- Page 163 and 164: displayed. Last Function RTU Federa
- Page 165 and 166: Name Column Federal Commander Digit
- Page 167 and 168: Record Checkbox Federal Commander D
<strong>Federal</strong> <strong>Commander</strong> <strong>Digital</strong> <strong>System</strong><br />
„PA Wave File‟ and „PA Smartmsg‟ only function on channels programmed for Codespear mode<br />
or Modem mode using the <strong>Federal</strong> <strong>Signal</strong> MSK Modem (2005249). Do not use these functions on<br />
channels programmed for SS2000. When using Modem mode with the MSK Modem, program #1<br />
of the UltraVoice must be programmed as:<br />
ARM<br />
PA OUTPUT<br />
DISARM<br />
Holiday Function<br />
The Holiday Function will override the normal function on selected holiday dates. See Holiday<br />
Time below.<br />
RTU or Zone Number<br />
This field selects which RTU(s) will sound for the respective alarm. To change selection, click on<br />
the desired radio button (Individual, Zone or All Call). For Individual and zone modes, enter the<br />
desired site or zone number in the Textbox provided.<br />
When Hotkey is selectedfor the Function or Holiday Function, these site selection controls are<br />
ignored. The site selection is obtained from the hotkey programming.<br />
Individual<br />
Only RTU number selected will sound for respective alarm.<br />
Zone<br />
RTUs in selected zone will sound for respective alarm.<br />
All Call<br />
All RTUs will sound for respective alarm.<br />
Mode<br />
The three radio buttons Disabled, Daily, and Weekly select the mode of operation for each<br />
respective alarm. To change this setting, click on the desired radio button. This selection is<br />
mutually exclusive and only one mode may be selected. For Weekly mode, the desired days of<br />
the week and week number must be selected.<br />
Disabled<br />
This alarm is not active and will not occur at any time.<br />
119<br />
<strong>System</strong> Setup