Thermo Ramsey - Hoferick Engineering GmbH
Thermo Ramsey - Hoferick Engineering GmbH Thermo Ramsey - Hoferick Engineering GmbH
Maintenance • Next is used to scroll between the pending alarms. • The string XXXXXXXXXXXX stands for one of the following alarm conditions: Table 3-1: Alarm Conditions Clock Fail Load Cell Fail RAM Fail ROM Fail Low Load High Load Low Rate High Rate Low Speed High Speed Cold Start Warm Start Calibrate Time Power Down Calibrate External Alarm 2 External Alarm 1 Overflow Totalizer External Alarm 3 Batch Deviation AZT Limited Hardware Configuration Change BCD Error Printer Error Math Error RIO COMM Error Communication Error PROFIBUS-DP COMM Error 3-8 Refer to Chapter 4 for more information. 3.8 Total Key and Associated Menus The TOTAL key accesses menus that contain detailed information for Master, Reset, Load Out, and Operator total tons counter. • Reset Total can be reset without a password. RESET TOTAL SINCE 00-00-0000 00000000 Tons RESET Press RESET to clear the Reset Total. No password required Maintenance Thermo Fisher Scientific REC 4175 Rev B
3.9 Start-Stop Keys 3.10 Calibration MASTER TOTAL SINCE 00-00-0000 00000000 Tons Maintenance • Load Out Total displays if the optional Load Out board is installed. (Refer to REC 3910 if this option is installed.) • Operator Total can be reset with a password. When RESET is pressed, the following screen is displayed: Do you wish to clear XXXXXX Total? YES NO Press YES to clear the total, press NO to skip. Enabled only if load out option is installed MAIN MENU 1 contains the CALIBRATION menu. MENU 1 is selected by pressing MENU until MAIN MENU 1 displays. Desired calibration scrolls are selected by pressing the soft keys directly below the desired scroll. -- MAIN MENU 1 -- Press MENU for more ZERO SPAN MAT’L CAL CAL CAL Thermo Fisher Scientific Maintenance REC 4175 Rev B 3-9
- Page 35 and 36: 2.2 Incoming Power WARNING THIS EQU
- Page 37 and 38: Thermo Fisher Scientific Operation
- Page 39 and 40: Thermo Fisher Scientific Operation
- Page 41 and 42: Figure 2-6: Micro-Tech Motherboard
- Page 43 and 44: OP 13 OP 11 OP 10 OP 5 Table 2-3: L
- Page 45 and 46: Table 2-7: Relay Output Board Integ
- Page 47 and 48: Table 2-11: Motherboard Wiring Conf
- Page 49 and 50: Figure 2-8: Belt Scale Weighbridge
- Page 51 and 52: Thermo Fisher Scientific Operation
- Page 53 and 54: Thermo Fisher Scientific Operation
- Page 55 and 56: Figure 2-17: Measure of Incline A90
- Page 57 and 58: Press key under HELP for more infor
- Page 59 and 60: Thermo Fisher Scientific Operation
- Page 61 and 62: 2.8 Selecting the Weighbridge Model
- Page 63 and 64: -- SC DATA SCROLL 3C-- Pivot to 1 s
- Page 65 and 66: Thermo Fisher Scientific Operation
- Page 67 and 68: 2.9 Defining Dimensional Parameters
- Page 69 and 70: Default: 350 Ohms Min: 10 Ohms Max:
- Page 71 and 72: Thermo Fisher Scientific Operation
- Page 73 and 74: Thermo Fisher Scientific Operation
- Page 75 and 76: ENTER the number of Belt revolution
- Page 77 and 78: Thermo Fisher Scientific Operation
- Page 79 and 80: 3.1 Overview Chapter 3 Operation 3.
- Page 81 and 82: Maintenance 3.3.1.3 Keypad The keyp
- Page 83 and 84: 3.6 Normal Power On Maintenance Whe
- Page 85: 3.7.2 Reset Total RESET 0000000 Ton
- Page 89 and 90: Maintenance EXIT returns to MAIN M
- Page 91 and 92: Maintenance Press START to initiate
- Page 93 and 94: Maintenance 6. Restart the conveyor
- Page 95 and 96: Maintenance 3.10.3.1.6 Recording Ne
- Page 97 and 98: 3. Select MANUAL The following scre
- Page 99 and 100: Maintenance • YES - if the operat
- Page 101 and 102: Maintenance YES: the amount of mate
- Page 103 and 104: 3.11.2 Calibration Menu CALIBRATION
- Page 105 and 106: 3.11.4 Main Menu 4 MAIN MENU 4 I/O
- Page 107 and 108: 3.11.5 Alarm Scroll ALARMS SCROLL 1
- Page 109 and 110: 3.11.6 Load Out Scroll LOAD OUT SCR
- Page 111 and 112: MAIN MENU 5 9D Contents String #2 9
- Page 113 and 114: 3.13 Calibration Report CALIBRATION
- Page 115 and 116: Chapter 4 Maintenance The maintenan
- Page 117 and 118: Replacement Parts 5. High Load The
- Page 119 and 120: Replacement Parts 22. Through 28. H
- Page 121 and 122: 4. Press ENTER, the following scree
- Page 123 and 124: Replacement Parts 4.7.1 No Password
- Page 125 and 126: 4.11 Cleaning Instructions Replacem
- Page 127 and 128: Chapter 5 Replacement Parts This ch
- Page 129 and 130: Replacement Parts Thermo Fisher Sci
- Page 131 and 132: 5.2 Phone/Fax for Thermo Scientific
- Page 133 and 134: 5.4 Disposal of Hazardous Waste Rep
- Page 135 and 136: A.1. Menu Displays Appendix A Menus
3.9 Start-Stop Keys<br />
3.10 Calibration<br />
MASTER TOTAL<br />
SINCE 00-00-0000<br />
00000000 Tons<br />
Maintenance<br />
• Load Out Total displays if the optional Load Out board is installed. (Refer<br />
to REC 3910 if this option is installed.)<br />
• Operator Total can be reset with a password.<br />
When RESET is pressed, the following screen is displayed:<br />
Do you wish to clear<br />
XXXXXX Total?<br />
YES NO<br />
Press YES to clear the total, press NO to skip.<br />
Enabled only if load out option is installed<br />
MAIN MENU 1 contains the CALIBRATION menu. MENU 1 is selected by<br />
pressing MENU until MAIN MENU 1 displays. Desired calibration scrolls are<br />
selected by pressing the soft keys directly below the desired scroll.<br />
-- MAIN MENU 1 --<br />
Press MENU for more<br />
ZERO SPAN MAT’L<br />
CAL CAL CAL<br />
<strong>Thermo</strong> Fisher Scientific Maintenance<br />
REC 4175 Rev B<br />
3-9
Change language