Thermo Ramsey - Hoferick Engineering GmbH
Thermo Ramsey - Hoferick Engineering GmbH Thermo Ramsey - Hoferick Engineering GmbH
Operation 2-38 • If # of Load Cells is 6: -- SC DATA SCROLL –8F- Load cell #6 res 350.000 Ohms ENTER Default: 350 Ohms Min: 10 Ohms Max: 2000 Ohms 2.9.4 Defining the Speed Input The speed input screen allows the operator to select the single speed sensor input (default value) or a simulated value using an internal timer. Simulation allows operation without a speed sensor. When simulated speed is selected, a conveyor running input is required (refer to the field wiring diagram). Note: If speed is selected as the third line display, the line will be blank in RUN mode when simulated speed is selected. -- SC DATA SCROLL –9- Speed input > single < CHOICE ENTER Default: SINGLE Choice: SINGLE, SIMULATED 2.9.5 Defining the Calibration Test Duration Zero and Span Calibrations are more accurate if executed on an entire belt revolution or multiple of it. Press either ACQUIRE or MANUAL, ACQUIRE is the recommended selection. For MANUAL, see Section 2.9.8. -- SC DATA SCROLL –11- Establish test duration ACQUIRE MANUAL Operation Thermo Fisher Scientific REC 4175 Rev B
Thermo Fisher Scientific Operation REC 4175 Rev B Operation Select ACQUIRE. Acquire is the recommended selection. • Acquiring the Test Duration When selecting FULL, use a 100 foot tape to measure the belt length to the nearest 0.1 foot. Reference a fixed point (an idler) on the conveyor when counting belt revolutions. See Section 2.5.1 for the recorded conveyor belt length. The PARTIAL (belt length measurement) selection enables the operator to acquire test duration without the entire belt length measurement. CAUTION THIS OPTION SHOULD ONLY BE USED WHEN BELT LENGTH EXCEEDS 1000 FEET. ACQUIRE TEST DUR Choose belt length measurement method FULL PARTIAL FULL is the recommended selection. If FULL is selected, continue with Step 16 below. If PARTIAL is selected, skip to Step 17. 2.9.6 Full Test Duration Acquisition If FULL is pressed, the operator is asked to enter the length of one belt revolution. Enter the length recorded in Section 2.5.1. Measure belt length to the nearest 0.1 feet. Enter length of one Belt revolution length 1000.0 Ft. ENTER ABORT If English Default: 1000.0 Ft or Mixed: Min: 1.0 Ft Max: 10000.0 Ft If Metric Default: 200 m Min: 0.5 m Max: 3000 m 2-39
- Page 19 and 20: About this Manual This manual provi
- Page 21 and 22: General Precaution Thermo Fisher Sc
- Page 23 and 24: Chapter 1 Introduction This instruc
- Page 25 and 26: Figure 1-2: Micro-Tech 3101 Panel M
- Page 27 and 28: Thermo Fisher Scientific Installati
- Page 29 and 30: Thermo Fisher Scientific Installati
- Page 31 and 32: Maximum Non-Destructive Input Volta
- Page 33 and 34: Chapter 2 Installation 2.1 Safety P
- Page 35 and 36: 2.2 Incoming Power WARNING THIS EQU
- Page 37 and 38: Thermo Fisher Scientific Operation
- Page 39 and 40: Thermo Fisher Scientific Operation
- Page 41 and 42: Figure 2-6: Micro-Tech Motherboard
- Page 43 and 44: OP 13 OP 11 OP 10 OP 5 Table 2-3: L
- Page 45 and 46: Table 2-7: Relay Output Board Integ
- Page 47 and 48: Table 2-11: Motherboard Wiring Conf
- Page 49 and 50: Figure 2-8: Belt Scale Weighbridge
- Page 51 and 52: Thermo Fisher Scientific Operation
- Page 53 and 54: Thermo Fisher Scientific Operation
- Page 55 and 56: Figure 2-17: Measure of Incline A90
- Page 57 and 58: Press key under HELP for more infor
- Page 59 and 60: Thermo Fisher Scientific Operation
- Page 61 and 62: 2.8 Selecting the Weighbridge Model
- Page 63 and 64: -- SC DATA SCROLL 3C-- Pivot to 1 s
- Page 65 and 66: Thermo Fisher Scientific Operation
- Page 67 and 68: 2.9 Defining Dimensional Parameters
- Page 69: Default: 350 Ohms Min: 10 Ohms Max:
- Page 73 and 74: Thermo Fisher Scientific Operation
- Page 75 and 76: ENTER the number of Belt revolution
- Page 77 and 78: Thermo Fisher Scientific Operation
- Page 79 and 80: 3.1 Overview Chapter 3 Operation 3.
- Page 81 and 82: Maintenance 3.3.1.3 Keypad The keyp
- Page 83 and 84: 3.6 Normal Power On Maintenance Whe
- Page 85 and 86: 3.7.2 Reset Total RESET 0000000 Ton
- Page 87 and 88: 3.9 Start-Stop Keys 3.10 Calibratio
- Page 89 and 90: Maintenance EXIT returns to MAIN M
- Page 91 and 92: Maintenance Press START to initiate
- Page 93 and 94: Maintenance 6. Restart the conveyor
- Page 95 and 96: Maintenance 3.10.3.1.6 Recording Ne
- Page 97 and 98: 3. Select MANUAL The following scre
- Page 99 and 100: Maintenance • YES - if the operat
- Page 101 and 102: Maintenance YES: the amount of mate
- Page 103 and 104: 3.11.2 Calibration Menu CALIBRATION
- Page 105 and 106: 3.11.4 Main Menu 4 MAIN MENU 4 I/O
- Page 107 and 108: 3.11.5 Alarm Scroll ALARMS SCROLL 1
- Page 109 and 110: 3.11.6 Load Out Scroll LOAD OUT SCR
- Page 111 and 112: MAIN MENU 5 9D Contents String #2 9
- Page 113 and 114: 3.13 Calibration Report CALIBRATION
- Page 115 and 116: Chapter 4 Maintenance The maintenan
- Page 117 and 118: Replacement Parts 5. High Load The
- Page 119 and 120: Replacement Parts 22. Through 28. H
<strong>Thermo</strong> Fisher Scientific Operation<br />
REC 4175 Rev B<br />
Operation<br />
Select ACQUIRE. Acquire is the recommended selection.<br />
• Acquiring the Test Duration<br />
When selecting FULL, use a 100 foot tape to measure the belt length to the<br />
nearest 0.1 foot. Reference a fixed point (an idler) on the conveyor when<br />
counting belt revolutions. See Section 2.5.1 for the recorded conveyor belt<br />
length.<br />
The PARTIAL (belt length measurement) selection enables the operator to<br />
acquire test duration without the entire belt length measurement.<br />
CAUTION<br />
THIS OPTION SHOULD ONLY BE USED WHEN<br />
BELT LENGTH EXCEEDS 1000 FEET.<br />
ACQUIRE TEST DUR<br />
Choose belt length<br />
measurement method<br />
FULL PARTIAL<br />
FULL is the recommended selection.<br />
If FULL is selected, continue with Step 16 below. If PARTIAL is selected,<br />
skip to Step 17.<br />
2.9.6 Full Test Duration Acquisition<br />
If FULL is pressed, the operator is asked to enter the length of one belt<br />
revolution. Enter the length recorded in Section 2.5.1. Measure belt length to<br />
the nearest 0.1 feet.<br />
Enter length of one<br />
Belt revolution<br />
length 1000.0 Ft.<br />
ENTER ABORT<br />
If English Default: 1000.0 Ft<br />
or Mixed: Min: 1.0 Ft<br />
Max: 10000.0 Ft<br />
If Metric Default: 200 m<br />
Min: 0.5 m<br />
Max: 3000 m<br />
2-39