Thermo Ramsey - Hoferick Engineering GmbH
Thermo Ramsey - Hoferick Engineering GmbH Thermo Ramsey - Hoferick Engineering GmbH
Operation 1.9 Technical Specifications 1-8 Enclosure Field Mount NEMA 4X (IP65), dust and watertight 17 x 13 x 7 inches Fiberglass reinforced polyester 2 position-mounting feet Steel chassis providing EMI/RFI shielding Panel Mount Size: 12 x 4 x 7.5 inches Material: Chromated mild steel Environmental Conditions Mounting Should be mounted as close to the load cells as possible without being exposed to excessive heat or moisture Field Mount suitable for outdoor mounting Temperature (Ambient) Storage: -40° to +158° F (-40° to +70° C) Operating: +14Ε to +122Ε F (-10Ε to +50Ε C) Relative Humidity Up to 95%, non-condensing Pollution Degree 2 Altitude Up to 6,561 ft (2000m) Power Requirements Voltage Range Nominal voltage +10%, -15% Nominal Voltage 115/230 VAC, selectable Nominal Frequency 50/60 Hz Fusing 400mA Slo-Blo, 110/120 VAC, Type T 200mA Slo-Blo 220/240 VAC, Type T Power Consumption 50 VA max Installation Thermo Fisher Scientific REC 4175 Rev B
Maximum Non-Destructive Input Voltage 150/300 VAC for 1 minute Over voltage Category Category II DC Power Supply Auxiliary Power Supply Output (Alarm Contacts, etc.) Output voltage: 24 VDC Isolation: Yes – 500 volts Output ripple: 1.0 V peak to peak typical Output current: Short circuit protection 600 mA maximum Thermo Fisher Scientific Installation REC 4175 Rev B Installation Load Cell (Weight) Load cell input circuits Number: Up to six (6) 350-ohm load cells in parallel. Cable distance 200 ft or less (3000 ft with sense) Sensitivity: 0.5mV/V to 3.5 mV/V (keyboard selectable) Input Impedance: 100 k-ohm minimum Maximum Usable Signal: 114% of 3mV/V Displayed A/D counts (3mV/V):112368 Isolation: Non-isolated Max non-destructive input voltage: ± 6 V relative to ground Load Cell Cable Shield: Connected to earth ground Load Cell Excitation Power Supply 10 VDC ±10%, 220 mA Minimum load impedance (operating) 58 ohms Output short circuit, 1.5 A maximum Excitation-Sense Circuitry 6 Wire System; cable distance over 200 ft. (not to exceed 3000 ft.). Nominal input voltage: ±5 VDC (10 volts) Input impedance: 100 k-ohm minimum Jumper selectable: Local or remote sense Speed Input Optically isolated Built in current source for dry contact use Powered by + 20 V SPU Supply 1-9
- Page 1 and 2: Micro-Tech 3000 Model 3101 Integrat
- Page 3 and 4: ©2004Thermo Fisher Scientific. All
- Page 5 and 6: Thermo Scientific Warranty The sell
- Page 7 and 8: Contents Contents..................
- Page 9 and 10: About this Manual 2.9.1 Idler Spaci
- Page 11 and 12: About this Manual A.3.3.8 Ending an
- Page 13 and 14: About this Manual A.11.2. Define Lo
- Page 15 and 16: List of Figures Figure 1-1: Micro-T
- Page 17 and 18: List of Tables Table 1-1: Symbol Id
- Page 19 and 20: About this Manual This manual provi
- Page 21 and 22: General Precaution Thermo Fisher Sc
- Page 23 and 24: Chapter 1 Introduction This instruc
- Page 25 and 26: Figure 1-2: Micro-Tech 3101 Panel M
- Page 27 and 28: Thermo Fisher Scientific Installati
- Page 29: Thermo Fisher Scientific Installati
- Page 33 and 34: Chapter 2 Installation 2.1 Safety P
- Page 35 and 36: 2.2 Incoming Power WARNING THIS EQU
- Page 37 and 38: Thermo Fisher Scientific Operation
- Page 39 and 40: Thermo Fisher Scientific Operation
- Page 41 and 42: Figure 2-6: Micro-Tech Motherboard
- Page 43 and 44: OP 13 OP 11 OP 10 OP 5 Table 2-3: L
- Page 45 and 46: Table 2-7: Relay Output Board Integ
- Page 47 and 48: Table 2-11: Motherboard Wiring Conf
- Page 49 and 50: Figure 2-8: Belt Scale Weighbridge
- Page 51 and 52: Thermo Fisher Scientific Operation
- Page 53 and 54: Thermo Fisher Scientific Operation
- Page 55 and 56: Figure 2-17: Measure of Incline A90
- Page 57 and 58: Press key under HELP for more infor
- Page 59 and 60: Thermo Fisher Scientific Operation
- Page 61 and 62: 2.8 Selecting the Weighbridge Model
- Page 63 and 64: -- SC DATA SCROLL 3C-- Pivot to 1 s
- Page 65 and 66: Thermo Fisher Scientific Operation
- Page 67 and 68: 2.9 Defining Dimensional Parameters
- Page 69 and 70: Default: 350 Ohms Min: 10 Ohms Max:
- Page 71 and 72: Thermo Fisher Scientific Operation
- Page 73 and 74: Thermo Fisher Scientific Operation
- Page 75 and 76: ENTER the number of Belt revolution
- Page 77 and 78: Thermo Fisher Scientific Operation
- Page 79 and 80: 3.1 Overview Chapter 3 Operation 3.
Operation<br />
1.9 Technical Specifications<br />
1-8<br />
Enclosure<br />
Field Mount<br />
NEMA 4X (IP65), dust and watertight<br />
17 x 13 x 7 inches<br />
Fiberglass reinforced polyester<br />
2 position-mounting feet<br />
Steel chassis providing EMI/RFI shielding<br />
Panel Mount<br />
Size: 12 x 4 x 7.5 inches<br />
Material: Chromated mild steel<br />
Environmental Conditions<br />
Mounting<br />
Should be mounted as close to the load cells as possible without being<br />
exposed to excessive heat or moisture<br />
Field Mount suitable for outdoor mounting<br />
Temperature (Ambient)<br />
Storage: -40° to +158° F (-40° to +70° C)<br />
Operating: +14Ε to +122Ε F (-10Ε to +50Ε C)<br />
Relative Humidity<br />
Up to 95%, non-condensing<br />
Pollution Degree<br />
2<br />
Altitude<br />
Up to 6,561 ft (2000m)<br />
Power Requirements<br />
Voltage Range<br />
Nominal voltage +10%, -15%<br />
Nominal Voltage<br />
115/230 VAC, selectable<br />
Nominal Frequency<br />
50/60 Hz<br />
Fusing<br />
400mA Slo-Blo, 110/120 VAC, Type T<br />
200mA Slo-Blo 220/240 VAC, Type T<br />
Power Consumption<br />
50 VA max<br />
Installation <strong>Thermo</strong> Fisher Scientific<br />
REC 4175 Rev B