Thermo Ramsey - Hoferick Engineering GmbH

More documents

Recommendations

Info

Menus A.12. MAIN MENU 5 Main Menu 5 is dedicated to the serial option. COMM A is used to set up the serial line and PRINT is used for setting up the printer output. Main Menu 5 does not appear unless an optional COMM A is installed. A.12.1. Communication A Scroll The MT 3101 has one serial channel, which can be configured using jumpers as an RS232 or an RS485 channel. The serial channel can be used for printing or for a serial communication with an intelligent device such as a PLC or a PC. An additional COMM A board can be installed and programmed, typically one for the printer and one for networking. The following screens define the communication parameters for the first and the second channel. COMM A SCROLL Baud Rate port #1 Password: Service > 9600 < CHOICE ENTER Default: 9600 Selections: 110, 150, 300, 600, 1200, 2400, 4800, 9600, 19200 - COMM. A SCROLL 2 - Set parity port #1 > No parity < CHOICE ENTER Default: NO PARITY Selections: EVEN PARITY, ODD PARITY, NO PARITY - COMM. A SCROLL 3 - Stop bits port #1 > 1 stop bit < CHOICE ENTER Default: 1 STOP BIT Selections: 1 STOP BIT, 2 STOP BITS Password: Service Password: Service A-66 Weighbridge Physical Parameters Thermo Fisher Scientific REC 4175 Rev B
Menus - COMM. A SCROLL 4 - Wordlength port #1 > 8 bits < CHOICE ENTER Default: 8 BITS Selections: 7 BITS, 8 BITS Some commonly used protocols are implemented in the system. See Communication Protocols, REC 3949, for the details. Possible selections are: • PC-MASTER -Thermo Scientific proprietary protocol: Multi Drop, Master Slave. • SIEMENS 3964R - A proprietary protocol of Siemens. Point to point, Multi Master. • ALLEN BRADLEY DF1 - A proprietary protocol of Allen Bradley. Multi Drop, Master Slave. • MODBUS - A proprietary protocol of AEG. Multi Drop, Master Slave. • PRINTER - Not a protocol, selects printer output. -COMM. A SCROLL 5 - Protocol port #1 > MODBUS < CHOICE ENTER Default: MODBUS Selections: PC-MASTER, SIEMENS 3964R, ALLEN BRADLEY DF1, MODBUS, PRINTER If the selected protocol is not PRINTER, the following screens define the ADDRESS of the device in the multi drop line, and the access permission from the remote supervisor. If NONE is selected, the supervisor has full access to the device. If LIMITED is selected; there is supervisor only access to those variables. If PROTECTED is selected, the unit is write protected. -COMM. A SCROLL 5A - Clear to send #1 > disabled < CHOICE ENTER Default: DISABLED Selections: DISABLED, ENABLED Password: Service Password: Service Password: Service Thermo Fisher Scientific Weighbridge Physical Parameters A-67 REC 4175 Rev B
Page 1 and 2:
Micro-Tech 3000 Model 3101 Integrat
Page 3 and 4:
©2004Thermo Fisher Scientific. All
Page 5 and 6:
Thermo Scientific Warranty The sell
Page 7 and 8:
Contents Contents..................
Page 9 and 10:
About this Manual 2.9.1 Idler Spaci
Page 11 and 12:
About this Manual A.3.3.8 Ending an
Page 13 and 14:
About this Manual A.11.2. Define Lo
Page 15 and 16:
List of Figures Figure 1-1: Micro-T
Page 17 and 18:
List of Tables Table 1-1: Symbol Id
Page 19 and 20:
About this Manual This manual provi
Page 21 and 22:
General Precaution Thermo Fisher Sc
Page 23 and 24:
Chapter 1 Introduction This instruc
Page 25 and 26:
Figure 1-2: Micro-Tech 3101 Panel M
Page 27 and 28:
Thermo Fisher Scientific Installati
Page 29 and 30:
Thermo Fisher Scientific Installati
Page 31 and 32:
Maximum Non-Destructive Input Volta
Page 33 and 34:
Chapter 2 Installation 2.1 Safety P
Page 35 and 36:
2.2 Incoming Power WARNING THIS EQU
Page 37 and 38:
Thermo Fisher Scientific Operation
Page 39 and 40:
Page 41 and 42:
Figure 2-6: Micro-Tech Motherboard
Page 43 and 44:
OP 13 OP 11 OP 10 OP 5 Table 2-3: L
Page 45 and 46:
Table 2-7: Relay Output Board Integ
Page 47 and 48:
Table 2-11: Motherboard Wiring Conf
Page 49 and 50:
Figure 2-8: Belt Scale Weighbridge
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Figure 2-17: Measure of Incline A90
Page 57 and 58:
Press key under HELP for more infor
Page 59 and 60:
Page 61 and 62:
2.8 Selecting the Weighbridge Model
Page 63 and 64:
-- SC DATA SCROLL 3C-- Pivot to 1 s
Page 65 and 66:
Page 67 and 68:
2.9 Defining Dimensional Parameters
Page 69 and 70:
Default: 350 Ohms Min: 10 Ohms Max:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
ENTER the number of Belt revolution
Page 77 and 78:
Page 79 and 80:
3.1 Overview Chapter 3 Operation 3.
Page 81 and 82:
Maintenance 3.3.1.3 Keypad The keyp
Page 83 and 84:
3.6 Normal Power On Maintenance Whe
Page 85 and 86:
3.7.2 Reset Total RESET 0000000 Ton
Page 87 and 88:
3.9 Start-Stop Keys 3.10 Calibratio
Page 89 and 90:
Maintenance EXIT returns to MAIN M
Page 91 and 92:
Maintenance Press START to initiate
Page 93 and 94:
Maintenance 6. Restart the conveyor
Page 95 and 96:
Maintenance 3.10.3.1.6 Recording Ne
Page 97 and 98:
3. Select MANUAL The following scre
Page 99 and 100:
Maintenance • YES - if the operat
Page 101 and 102:
Maintenance YES: the amount of mate
Page 103 and 104:
3.11.2 Calibration Menu CALIBRATION
Page 105 and 106:
3.11.4 Main Menu 4 MAIN MENU 4 I/O
Page 107 and 108:
3.11.5 Alarm Scroll ALARMS SCROLL 1
Page 109 and 110:
3.11.6 Load Out Scroll LOAD OUT SCR
Page 111 and 112:
MAIN MENU 5 9D Contents String #2 9
Page 113 and 114:
3.13 Calibration Report CALIBRATION
Page 115 and 116:
Chapter 4 Maintenance The maintenan
Page 117 and 118:
Replacement Parts 5. High Load The
Page 119 and 120:
Replacement Parts 22. Through 28. H
Page 121 and 122:
4. Press ENTER, the following scree
Page 123 and 124:
Replacement Parts 4.7.1 No Password
Page 125 and 126:
4.11 Cleaning Instructions Replacem
Page 127 and 128:
Chapter 5 Replacement Parts This ch
Page 129 and 130:
Replacement Parts Thermo Fisher Sci
Page 131 and 132:
5.2 Phone/Fax for Thermo Scientific
Page 133 and 134:
5.4 Disposal of Hazardous Waste Rep
Page 135 and 136:
A.1. Menu Displays Appendix A Menus
Page 137 and 138:
Menus EXIT: returns to Main Menu 1
Page 139 and 140:
Menus When ADV is pressed, the syst
Page 141 and 142:
Menus A.3.3.3 Starting a Test Weigh
Page 143 and 144:
Menus 1. Complete is flashing 2. Th
Page 145 and 146:
Menus A.3.3.7 Ending an Auto Span P
Page 147 and 148:
Menus 4. Press CONTINUE The followi
Page 149 and 150: Menus If R-CAL, WEIGHTS, or CHAINS
Page 151 and 152: Menus A.5.3. Length Units -- DISPLA
Page 153 and 154: Menus A.5.9. Displayed Damping Fact
Page 155 and 156: Menus -- SC DATA SCROLL 3 -- Belt s
Page 157 and 158: Menus Only if # of weigh idlers ≥
Page 159 and 160: Menus Carry Roll to Carriage Height
Page 161 and 162: Menus A.6.6.3 Load Cell Resistance
Page 163 and 164: Menus A.7.1.1 Defining the R-Cal Pa
Page 165 and 166: Menus The scroll displays the date
Page 167 and 168: Menus When START is pressed, the sy
Page 169 and 170: Menus When test duration is finishe
Page 171 and 172: Menus The following scrolls are onl
Page 173 and 174: Menus A SERVICE password is require
Page 175 and 176: Menus Default: 3497 Min: 0 Max: 300
Page 177 and 178: Menus A.9.5. Display Software Versi
Page 179 and 180: Menus A.9.8. Force Cold Start This
Page 181 and 182: Menus WARNING IF THE USER PRESSES C
Page 183 and 184: Menus A.9.18. Test BCD Output Board
Page 185 and 186: Menus Default: (1st) 0 sec, (2nd) 0
Page 187 and 188: Menus A.10.4. Setup Inclination Com
Page 189 and 190: Menus Appendix Table A-4: Mother Bo
Page 191 and 192: Menus Appendix Table A-6: Available
Page 193 and 194: Menus WARNING CHANGING THE DEFINITI
Page 195 and 196: Menus - I/O DEF SCROLL 9A- BCD inpu
Page 197 and 198: Menus A.11.1. Define Rate Alarm Use
Page 199: Menus - ALARM SCROLL 3A - Low speed
Page 203 and 204: Menus Default: 8 BITS Selections: 7
Page 205 and 206: Menus A form feed character can be
Page 207 and 208: Menus There are three ways for defi
Page 209 and 210: Menus Once you have defined the str
Page 211 and 212: Menus The Reset Total: - PRINTER SC
Page 213 and 214: Menus A.12.5. The PRINT Key The PRI
Page 215 and 216: Menus A.13. MAIN MENU 6 Main Menu 6
Page 217 and 218: Appendix B Weighbridge Physical Par
Page 219 and 220: Digital Input/Output Appendix Figur
Page 221 and 222: Digital Input/Output # MODEL BELT W
Page 223 and 224: Digital Input/Output # MODEL BELT W
Page 225 and 226: Appendix C Linearization Request RE
Page 227 and 228: Appendix D Digital Input/Output The
Page 229 and 230: Digital Input/Output D.2. Digital I
Page 231 and 232: Digital Input/Output Thermo Fisher
Page 235 and 236: Digital Input/Output D.4. Analog I/
Page 241 and 242: Appendix E Multi-Point Calibration
Page 243 and 244: Multi-Point Calibration E.2.2. Digi
Page 245 and 246: Appendix F Minor Calibration Notes:
Page 247 and 248: Appendix G Optional Documentation T
Page 249 and 250: Appendix H Engineering Drawings Fi
show all

Thermo Ramsey - Hoferick Engineering GmbH

Create successful ePaper yourself

Delete template?

Save as template?