Thermo Ramsey - Hoferick Engineering GmbH
Thermo Ramsey - Hoferick Engineering GmbH Thermo Ramsey - Hoferick Engineering GmbH
Menus A.10.8. Define BCD Output Data If an optional load out board is installed, the user can select the related variable. - I/O DEF SCROLL 8 - BCD Output variable > Rate < CHOICES ENTER Default: OFF Selections: OFF, RATE, LOAD, SPEED If a selection other than OFF is made, the following screens allow the user to define the polarity and the parity check of the BCD output. The polarity selection reverses the signals from NO to NC and vice versa. If a parity criterion is selected, the most significant bit of the BCD output is used for parity check. - I/O DEF SCROLL 8A- BCD Output polarity > Positive < CHOICES ENTER Default: NEGATIVE Selections: POSITIVE, NEGATIVE - I/O DEF SCROLL 8B- BCD Output parity > Yes < CHOICES ENTER Default: NO Selections: NO, YES A.10.9. Define BCD Input Data If an optional load out input board is installed, the following screens allow the user to define the related variable and the polarity of the signals. I/O DEF SCROLL 9 - BCD Input variable > Load out setpoint Default: OFF Selections: OFF, BATCH PRE-ACT, BATCH SETPOINT Only if BCD input is not set to OFF: Password: Service Password: Service Password: Service Password: Service A-60 Weighbridge Physical Parameters Thermo Fisher Scientific REC 4175 Rev B
Menus - I/O DEF SCROLL 9A- BCD input polarity > Positive < CHOICES ENTER Default: OFF Selections: OFF, BATCH PRE-ACT, BATCH SETPOINT Only if BCD input is not set to OFF: - I/O DEF SCROLL 9A- BCD input polarity > Positive < CHOICES ENTER Default: NEGATIVE Selections: NEGATIVE, POSITIVE A.10.10. Clip Detector Option The clip detector option reduces flow rate errors on light loaded belts caused by conveyor belt weight variances. Turning on Auto Zero Tracking in the Cal Data Scroll enables the clip detector. The clip detector is normally a proximity switch that senses a metal target attached to the belt. In manual mode, the clip detector freezes the flow rate when the clip is detected and maintains it frozen for the programmed length. Totalization is not affected. In automatic, the Integrator automatically detects tare variations and compensates for them. If the clip detector is assigned to one digital I/O input, the following screens appear. - I/O DEF SCROLL 10- Clip detector mode MANUAL CHOICE ENTER Password: Service Password: Service Password: Service Default: MANUAL Choices: MANUAL, AUTO In the MANUAL mode, the user must enter the length of belt, which is affected, by the belt splice. The system freezes the belt loading when the clip is detected and maintains it frozen until the specified belt length has passed. Thermo Fisher Scientific Weighbridge Physical Parameters A-61 REC 4175 Rev B
- Page 143 and 144: Menus 1. Complete is flashing 2. Th
- Page 145 and 146: Menus A.3.3.7 Ending an Auto Span P
- Page 147 and 148: Menus 4. Press CONTINUE The followi
- Page 149 and 150: Menus If R-CAL, WEIGHTS, or CHAINS
- Page 151 and 152: Menus A.5.3. Length Units -- DISPLA
- Page 153 and 154: Menus A.5.9. Displayed Damping Fact
- Page 155 and 156: Menus -- SC DATA SCROLL 3 -- Belt s
- Page 157 and 158: Menus Only if # of weigh idlers ≥
- Page 159 and 160: Menus Carry Roll to Carriage Height
- Page 161 and 162: Menus A.6.6.3 Load Cell Resistance
- Page 163 and 164: Menus A.7.1.1 Defining the R-Cal Pa
- Page 165 and 166: Menus The scroll displays the date
- Page 167 and 168: Menus When START is pressed, the sy
- Page 169 and 170: Menus When test duration is finishe
- Page 171 and 172: Menus The following scrolls are onl
- Page 173 and 174: Menus A SERVICE password is require
- Page 175 and 176: Menus Default: 3497 Min: 0 Max: 300
- Page 177 and 178: Menus A.9.5. Display Software Versi
- Page 179 and 180: Menus A.9.8. Force Cold Start This
- Page 181 and 182: Menus WARNING IF THE USER PRESSES C
- Page 183 and 184: Menus A.9.18. Test BCD Output Board
- Page 185 and 186: Menus Default: (1st) 0 sec, (2nd) 0
- Page 187 and 188: Menus A.10.4. Setup Inclination Com
- Page 189 and 190: Menus Appendix Table A-4: Mother Bo
- Page 191 and 192: Menus Appendix Table A-6: Available
- Page 193: Menus WARNING CHANGING THE DEFINITI
- Page 197 and 198: Menus A.11.1. Define Rate Alarm Use
- Page 199 and 200: Menus - ALARM SCROLL 3A - Low speed
- Page 201 and 202: Menus - COMM. A SCROLL 4 - Wordleng
- Page 203 and 204: Menus Default: 8 BITS Selections: 7
- Page 205 and 206: Menus A form feed character can be
- Page 207 and 208: Menus There are three ways for defi
- Page 209 and 210: Menus Once you have defined the str
- Page 211 and 212: Menus The Reset Total: - PRINTER SC
- Page 213 and 214: Menus A.12.5. The PRINT Key The PRI
- Page 215 and 216: Menus A.13. MAIN MENU 6 Main Menu 6
- Page 217 and 218: Appendix B Weighbridge Physical Par
- Page 219 and 220: Digital Input/Output Appendix Figur
- Page 221 and 222: Digital Input/Output # MODEL BELT W
- Page 223 and 224: Digital Input/Output # MODEL BELT W
- Page 225 and 226: Appendix C Linearization Request RE
- Page 227 and 228: Appendix D Digital Input/Output The
- Page 229 and 230: Digital Input/Output D.2. Digital I
- Page 231 and 232: Digital Input/Output Thermo Fisher
- Page 233 and 234: Digital Input/Output Appendix Figur
- Page 235 and 236: Digital Input/Output D.4. Analog I/
- Page 237 and 238: Digital Input/Output Appendix Figur
- Page 239 and 240: Digital Input/Output Appendix Figur
- Page 241 and 242: Appendix E Multi-Point Calibration
- Page 243 and 244: Multi-Point Calibration E.2.2. Digi
Menus<br />
A.10.8. Define BCD Output Data<br />
If an optional load out board is installed, the user can select the related variable.<br />
- I/O DEF SCROLL 8 -<br />
BCD Output variable<br />
> Rate <<br />
CHOICES ENTER<br />
Default: OFF<br />
Selections: OFF, RATE, LOAD, SPEED<br />
If a selection other than OFF is made, the following screens allow the user to<br />
define the polarity and the parity check of the BCD output. The polarity<br />
selection reverses the signals from NO to NC and vice versa. If a parity<br />
criterion is selected, the most significant bit of the BCD output is used for parity<br />
check.<br />
- I/O DEF SCROLL 8A-<br />
BCD Output polarity<br />
> Positive <<br />
CHOICES ENTER<br />
Default: NEGATIVE<br />
Selections: POSITIVE, NEGATIVE<br />
- I/O DEF SCROLL 8B-<br />
BCD Output parity<br />
> Yes <<br />
CHOICES ENTER<br />
Default: NO<br />
Selections: NO, YES<br />
A.10.9. Define BCD Input Data<br />
If an optional load out input board is installed, the following screens allow the<br />
user to define the related variable and the polarity of the signals.<br />
I/O DEF SCROLL 9 -<br />
BCD Input variable<br />
> Load out setpoint<br />
Default: OFF<br />
Selections: OFF, BATCH PRE-ACT, BATCH SETPOINT<br />
Only if BCD input is not set to OFF:<br />
Password: Service<br />
Password: Service<br />
Password: Service<br />
Password: Service<br />
A-60 Weighbridge Physical Parameters <strong>Thermo</strong> Fisher Scientific<br />
REC 4175 Rev B