Thermo Ramsey - Hoferick Engineering GmbH
Thermo Ramsey - Hoferick Engineering GmbH Thermo Ramsey - Hoferick Engineering GmbH
Menus A.9.15. Test Communication A The following screen allows checking the installed serial lines using a loop back type test. The maximum line number is 2; Transmit must be tied to receive for this test. "Port 1" is standard and "Port 2" is shown only if optional Comm boards are detected. - TEST SCROLL 8 - Test Communication A Port 1 Port 2 By pressing the PORT 1 or the PORT 2 soft key, the test is initiated. A test pattern is sent out on the TX output and read on the RX input. If the test fails, the message "Test Failed" is shown; otherwise, the message "Test Passed" is displayed. A.9.15.1 Test RS232 To test RS232 the test requires a hardware jumper to be installed between terminals TB3-22 (RX) and TB3-21 (TX). A.9.15.2 Test RS485 To test the RS485 the test requires a hardware jumper to be installed between terminals TB3-21 and TB3-28 to TB3-20 and TB3-29. A.9.16. Test Communication B This test is similar to the previous one but works for the field bus version of the communication board. - TEST SCROLL 9 - Test communication B START A.9.17. Test BCD Input Board If an optional BCD input card is detected, the following screen appears. The test is similar to the digital input test. - TEST SCROLL 10 - BCD Input test 0000 Password: Service A-48 Weighbridge Physical Parameters Thermo Fisher Scientific REC 4175 Rev B
Menus A.9.18. Test BCD Output Board The following test is displayed if an optional BCD output board is detected. Default: 0 Min: 0 Max: 9999 or 7999 if parity check enabled To force the outputs, enter a number followed by ENTER. The CLEAR key appears indicating that the output is being forced to a value. By pressing CLEAR, the output is freed. A.9.19. Test the Keyboard and Switches A.10. Main Menu 4 - TEST SCROLL 11 - BCD Output test 0000 ENTER CLEAR - TEST SCROLL 12 - Keyboard + switches Key: ______ Press the RUN key twice to exit. All other keys, including MENU, are displayed but not executed. The following section defines the input output (I/O) and alarms. - MAIN MENU 4 - Press MENU for more I/O ALARMS DEFINE DEFINE Thermo Fisher Scientific Weighbridge Physical Parameters A-49 REC 4175 Rev B
- Page 131 and 132: 5.2 Phone/Fax for Thermo Scientific
- Page 133 and 134: 5.4 Disposal of Hazardous Waste Rep
- Page 135 and 136: A.1. Menu Displays Appendix A Menus
- Page 137 and 138: Menus EXIT: returns to Main Menu 1
- Page 139 and 140: Menus When ADV is pressed, the syst
- Page 141 and 142: Menus A.3.3.3 Starting a Test Weigh
- Page 143 and 144: Menus 1. Complete is flashing 2. Th
- Page 145 and 146: Menus A.3.3.7 Ending an Auto Span P
- Page 147 and 148: Menus 4. Press CONTINUE The followi
- Page 149 and 150: Menus If R-CAL, WEIGHTS, or CHAINS
- Page 151 and 152: Menus A.5.3. Length Units -- DISPLA
- Page 153 and 154: Menus A.5.9. Displayed Damping Fact
- Page 155 and 156: Menus -- SC DATA SCROLL 3 -- Belt s
- Page 157 and 158: Menus Only if # of weigh idlers ≥
- Page 159 and 160: Menus Carry Roll to Carriage Height
- Page 161 and 162: Menus A.6.6.3 Load Cell Resistance
- Page 163 and 164: Menus A.7.1.1 Defining the R-Cal Pa
- Page 165 and 166: Menus The scroll displays the date
- Page 167 and 168: Menus When START is pressed, the sy
- Page 169 and 170: Menus When test duration is finishe
- Page 171 and 172: Menus The following scrolls are onl
- Page 173 and 174: Menus A SERVICE password is require
- Page 175 and 176: Menus Default: 3497 Min: 0 Max: 300
- Page 177 and 178: Menus A.9.5. Display Software Versi
- Page 179 and 180: Menus A.9.8. Force Cold Start This
- Page 181: Menus WARNING IF THE USER PRESSES C
- Page 185 and 186: Menus Default: (1st) 0 sec, (2nd) 0
- Page 187 and 188: Menus A.10.4. Setup Inclination Com
- Page 189 and 190: Menus Appendix Table A-4: Mother Bo
- Page 191 and 192: Menus Appendix Table A-6: Available
- Page 193 and 194: Menus WARNING CHANGING THE DEFINITI
- Page 195 and 196: Menus - I/O DEF SCROLL 9A- BCD inpu
- Page 197 and 198: Menus A.11.1. Define Rate Alarm Use
- Page 199 and 200: Menus - ALARM SCROLL 3A - Low speed
- Page 201 and 202: Menus - COMM. A SCROLL 4 - Wordleng
- Page 203 and 204: Menus Default: 8 BITS Selections: 7
- Page 205 and 206: Menus A form feed character can be
- Page 207 and 208: Menus There are three ways for defi
- Page 209 and 210: Menus Once you have defined the str
- Page 211 and 212: Menus The Reset Total: - PRINTER SC
- Page 213 and 214: Menus A.12.5. The PRINT Key The PRI
- Page 215 and 216: Menus A.13. MAIN MENU 6 Main Menu 6
- Page 217 and 218: Appendix B Weighbridge Physical Par
- Page 219 and 220: Digital Input/Output Appendix Figur
- Page 221 and 222: Digital Input/Output # MODEL BELT W
- Page 223 and 224: Digital Input/Output # MODEL BELT W
- Page 225 and 226: Appendix C Linearization Request RE
- Page 227 and 228: Appendix D Digital Input/Output The
- Page 229 and 230: Digital Input/Output D.2. Digital I
- Page 231 and 232: Digital Input/Output Thermo Fisher
Menus<br />
A.9.18. Test BCD Output Board<br />
The following test is displayed if an optional BCD output board is detected.<br />
Default: 0<br />
Min: 0<br />
Max: 9999 or 7999 if parity check enabled<br />
To force the outputs, enter a number followed by ENTER. The CLEAR key<br />
appears indicating that the output is being forced to a value. By pressing<br />
CLEAR, the output is freed.<br />
A.9.19. Test the Keyboard and Switches<br />
A.10. Main Menu 4<br />
- TEST SCROLL 11 -<br />
BCD Output test<br />
0000<br />
ENTER CLEAR<br />
- TEST SCROLL 12 -<br />
Keyboard + switches<br />
Key: ______<br />
Press the RUN key twice to exit. All other keys, including MENU, are<br />
displayed but not executed.<br />
The following section defines the input output (I/O) and alarms.<br />
- MAIN MENU 4 -<br />
Press MENU for more<br />
I/O ALARMS<br />
DEFINE DEFINE<br />
<strong>Thermo</strong> Fisher Scientific Weighbridge Physical Parameters A-49<br />
REC 4175 Rev B