PROFIBUS-DP Slave Protocol Manual Ramsey Micro-Tech™ 3000 ...
PROFIBUS-DP Slave Protocol Manual Ramsey Micro-Tech™ 3000 ... PROFIBUS-DP Slave Protocol Manual Ramsey Micro-Tech™ 3000 ...
Profibus-DP Model 3102 3-18 11 AutoRefill - wait charge interlock 12 AutoRefill - wait delay at the start 13 AutoRefill - refilling 14 AutoRefill - refill end, wait stabilization time 15 Discharge batch - wait discharge interlock 16 Discharge batch - wait delay at the start 17 Discharge batch - discharging at high rate 18 Discharge batch - discharging at low rate 19 Discharge batch - discharge end, wait stab.time 20 Discharge - wait discharge interlock 21 Discharge - wait delay at the start 22 Discharge - discharging 23 Discharge - discharge end, wait stab.time 24 Time - wait interlock 25 Time - wait start delay 26 Time - batching 27 Time - end charge 28 Recipe line end 29 Next recipe line The Batch Stop Flags give indication about the cause of a batch stop condition. Batch Stop Value Cause of the stop 0 Not stop 1 Stop command 2 Discharge device open 3 Charge interlock 4 Discharge interlock 5 Shut down active 6 Power down REC XXXXX
REC XXXXX Profibus-DP Model 3102 The Batch Abort Flags give indication about the cause of a batch abort condition. Batch Abort Value Cause of the abort 0 Not abort 1 Abort command 2 Bad recipe 3 Bad external cycles set 4 Bad external set point set 5 Manual Tot_Comp# Define the first component for the access to the component total registers. See Comp#_Tot and Comp#_LastTot. Tot_Rec# Define the first recipe for the access to the recipe total registers. See Rec#_Tot and Rec#_LastTot 3.7 Read Data Groups Composition 3.7.1 Read Group 0 – Dynamic Variables and Status Read Group 0 is the default group the Micro-Tech 3100 sends the master for a read request if the master does not change request (Table 3-6). It contains dynamic values (rate, weight) and information about the status of the Micro-Tech 3000. TABLE 3-6 READ GROUP 0 [VAT1] elem. # register type Offset (words) Note 5 Staus (1) integer 4 6 Staus (2) integer 5 7 Staus (3) integer 6 8 Staus (4) integer 7 9 Alarms (1) integer 8 10 Alarms (2) integer 9 11 Alarms (3) integer 10 12 Alarms (4) integer 11 13 Alarms (5) integer 12 3-19
- Page 1: PROFIBUS-DP Slave Protocol Manual P
- Page 4 and 5: Revision History Preliminary Decemb
- Page 6 and 7: Profibus-DP Model 3102 ii 3.7.6 Rea
- Page 8 and 9: Profibus -DP Model 3102 iv REC XXXX
- Page 11 and 12: Profibus-DP Model 3102 Chapter 1 In
- Page 13 and 14: Profibus-DP Model 3102 Chapter 2 In
- Page 15 and 16: 2.3.1. Bus Connector Wiring Refer t
- Page 17 and 18: Profibus-DP Model 3102 Chapter 3 Op
- Page 19 and 20: Profibus-DP Model 3102 If the baud
- Page 21 and 22: Profibus-DP Model 3102 3.3.2 Read O
- Page 23 and 24: Profibus-DP Model 3102 LE Limits Er
- Page 25 and 26: Profibus-DP Model 3102 - refresh t.
- Page 27 and 28: Alarms 4 REC XXXXX Profibus-DP Mode
- Page 29 and 30: REC XXXXX Profibus-DP Model 3102 Co
- Page 31 and 32: IO_image 11 - 16out/4in boards #3 o
- Page 33: REC XXXXX Profibus-DP Model 3102 St
- Page 37 and 38: REC XXXXX TABLE 3-8 READ GROUP 2 [V
- Page 39 and 40: REC XXXXX Profibus-DP Model 3102 3.
- Page 41: 3.8.2 Write Group 101 - Dynamic Dat
- Page 44 and 45: Profibus DP Model 3100 Examples Som
- Page 46 and 47: Profibus DP Model 3100 where: RBD i
- Page 48: Profibus DP Model 3100 Buffers dime
Profibus-<strong>DP</strong> Model 3102<br />
3-18<br />
11 AutoRefill - wait charge interlock<br />
12 AutoRefill - wait delay at the start<br />
13 AutoRefill - refilling<br />
14 AutoRefill - refill end, wait stabilization time<br />
15 Discharge batch - wait discharge interlock<br />
16 Discharge batch - wait delay at the start<br />
17 Discharge batch - discharging at high rate<br />
18 Discharge batch - discharging at low rate<br />
19 Discharge batch - discharge end, wait stab.time<br />
20 Discharge - wait discharge interlock<br />
21 Discharge - wait delay at the start<br />
22 Discharge - discharging<br />
23 Discharge - discharge end, wait stab.time<br />
24 Time - wait interlock<br />
25 Time - wait start delay<br />
26 Time - batching<br />
27 Time - end charge<br />
28 Recipe line end<br />
29 Next recipe line<br />
The Batch Stop Flags give indication about the cause of a batch stop condition.<br />
Batch Stop<br />
Value Cause of the stop<br />
0 Not stop<br />
1 Stop command<br />
2 Discharge device open<br />
3 Charge interlock<br />
4 Discharge interlock<br />
5 Shut down active<br />
6 Power down<br />
REC XXXXX