A Text Book on Engineering Graphics - Central Board of Secondary ...
A Text Book on Engineering Graphics - Central Board of Secondary ... A Text Book on Engineering Graphics - Central Board of Secondary ...
172 PULLEYS EXERCISE 4 : Fig 7.10 shows the orthographic views of a single groove V-belt pulley. Draw its following views with shaft and key of proper size : (i) Front View, upper half in section (ii) Side View looking from left side. Write title and scale used. Draw projection symbol. Give '6' important dimensions. Ø 25, 4 HOLES ON Ø 125 PITCH CIRCLE A A KEYWAY 8x3 18 Ø 50 20 30° 30 25 4 Ø 30 Ø 250 SIDE VIEW SECTIONAL FRONT VIEW SINGLE GROOVE V - BELT PULLEY Fig 7.10 60 ENGINEERING GRAPHICS
- Page 129 and 130: ROD JOINTS KNUCKLE JOINT OR PIN JOI
- Page 131 and 132: ROD JOINTS Question: fig 4.19(a) sh
- Page 133 and 134: ROD JOINTS Question: The figure 4.2
- Page 135 and 136: ROD JOINTS Exercises: The three vie
- Page 137 and 138: ROD JOINTS Dimensions of a Gib and
- Page 139 and 140: ROD JOINTS 96 66 12 GIB 26 COTTER T
- Page 141 and 142: ROD JOINTS Exercise: The two views
- Page 143 and 144: 5 CHAPTER Machines use various part
- Page 145 and 146: TIE-ROD AND PIPE JOINTS (We have di
- Page 147 and 148: TIE-ROD AND PIPE JOINTS Example 2:
- Page 149 and 150: TIE-ROD AND PIPE JOINTS RH SIDE VIE
- Page 151 and 152: TIE-ROD AND PIPE JOINTS 5.2.1.1 FEA
- Page 153 and 154: TIE-ROD AND PIPE JOINTS (1) FLANGE
- Page 155 and 156: TIE-ROD AND PIPE JOINTS Let us cons
- Page 157 and 158: TIE-ROD AND PIPE JOINTS WHAT HAVE W
- Page 159 and 160: SHAFT COUPLINGS 6.1 FLANGE COUPLING
- Page 161 and 162: SHAFT COUPLINGS It can also be noti
- Page 163 and 164: SHAFT COUPLINGS Ø100 Ø75 Ø50 Ø2
- Page 165 and 166: SHAFT COUPLINGS Exercise 6.1 Fig 6.
- Page 167 and 168: SHAFT COUPLINGS ASSEMBLED PICTORIAL
- Page 169 and 170: SHAFT COUPLINGS Let us take another
- Page 171 and 172: SHAFT COUPLINGS Exercise 6.2 1. FIG
- Page 173 and 174: CHAPTER 7 7.1 INTRODUCTION PULLEYS
- Page 175 and 176: PULLEYS So pulley is a simple machi
- Page 177 and 178: PULLEYS Solution : Ø144 Ø126 Ø11
- Page 179: PULLEYS Example 3 : Draw the Front
172<br />
PULLEYS<br />
EXERCISE 4 : Fig 7.10 shows the orthographic views <strong>of</strong> a single groove V-belt pulley. Draw its<br />
following views with shaft and key <strong>of</strong> proper size :<br />
(i) Fr<strong>on</strong>t View, upper half in secti<strong>on</strong><br />
(ii) Side View looking from left side.<br />
Write title and scale used. Draw projecti<strong>on</strong> symbol. Give '6' important dimensi<strong>on</strong>s.<br />
Ø 25, 4 HOLES ON Ø 125 PITCH CIRCLE<br />
A<br />
A<br />
KEYWAY 8x3<br />
18<br />
Ø 50<br />
20<br />
30°<br />
30<br />
25<br />
4<br />
Ø 30<br />
Ø 250<br />
SIDE VIEW SECTIONAL FRONT VIEW<br />
SINGLE GROOVE V - BELT PULLEY<br />
Fig 7.10<br />
60<br />
ENGINEERING GRAPHICS