You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Operating Instructions for the Model Watercutter<br />
Order No. 2203<br />
Description of the model<br />
• Almost-Ready-to-Run (ARTR) model<br />
• GRP hull and deck pre-bonded<br />
• Powerful brushless electric motor with hydro drive<br />
• Stainless steel drive and rudder shaft<br />
• Water-cooled moor, rudder linkages sealed with rubber accordion seals<br />
• Rudder servo and electronic speed controller pre-installed<br />
• Included in delivery: Hull pre-bonded with deck, cockpit canopy, motor, shaft with drive system<br />
• Ship stand, applied decal sheet, controller, and servo<br />
Specification<br />
Overall length about 570 mm<br />
Beam about 275 mm<br />
Total weight about 1.75 kg<br />
Manufacturer's declaration of the company <strong>Graupner</strong> GmbH & Co KG<br />
Content of the manufacturer's declaration<br />
If material defects or manufacturing faults should arise in a product distributed by us in the Federal Republic<br />
of Germany and purchased by a consumer (§ 13 BGB), we, <strong>Graupner</strong> GmbH & Co. KG, Kirchheim/Teck,<br />
Germany, acknowledge the obligation to correct those defects within the limitations described below.<br />
The consumer is not entitled to make claims under this manufacturer’s declaration if the failure in the usability<br />
of the product is due to natural wear, use under competition conditions, incompetent or improper use (including<br />
incorrect installation), or external influences.<br />
This manufacturer’s declaration does not affect the consumer’s legal or contractual rights regarding defects<br />
arising from the purchase contract between the consumer and the vendor (dealer).<br />
Extent of the guarantee<br />
If a claim is made under guarantee, we undertake at our discretion to repair or replace the defective goods.<br />
We will not consider further claims, especially for reimbursement of costs relating to the defect (such as installation<br />
/ removal costs) and compensation for consequent damages unless they are allowed by statute.<br />
This does not affect claims based on legal regulations, especially according to product liability law.<br />
Guarantee requirements<br />
The purchaser is required to make the guarantee claim in writing and must enclose original proof of purchase<br />
(such as invoice, receipt, delivery note) and this guarantee card. The defective goods must be sent to<br />
us at the purchaser's own cost, using the address stated above.<br />
Fa. <strong>Graupner</strong> GmbH & CO KG, Serviceabteilung,<br />
Henriettenstr.94 -96, D 73230 Kirchheim/Teck<br />
GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY<br />
Not liable for printing errors. We reserve the right to make technical modifications. 11/2011 1
The purchaser should state the material defect or manufacturing fault or the symptoms of the fault in as accurate<br />
a manner as possible so that we can check whether our guarantee obligation is applicable.<br />
The goods are transported from the consumer to us and from us to the consumer at the risk of the consumer.<br />
Duration of validity<br />
This declaration only applies to claims made to us during the claim period as stated in this declaration. Die<br />
The claim period is 24 months from the date of purchase of the product by the consumer from a dealer in the<br />
Federal Republic of Germany (date of purchase). If a defect arises after the end of the claim period, or if the<br />
evidence or documents required according to this declaration in order to make the claim valid are not presented<br />
until after this period, then the consumer forfeits any rights or claims from this declaration.<br />
Limitation by lapse of time<br />
If we do not acknowledge the validity of a claim that is properly made under this declaration within the claim<br />
period, all claims based on this declaration expire after six months from the time of claim, but not before the<br />
end of the claim period.<br />
Applicable law<br />
This declaration, and the claims, rights and obligations arising from it, are based exclusively on the applicable<br />
German Law, without the norms of international private law, and excluding UN retail law.<br />
Important safety notes<br />
You have acquired a kit that can be assembled into a fully working RC model - when fitted out with suitable<br />
accessories. However, GRAUPNER has no control over whether you observe the instructions for the installation<br />
and operation of the model or the use and maintenance of the associated components. For this reason<br />
GRAUPNER assumes no liability for losses, damage, or costs, which are incurred due to the incorrect use of<br />
our products or due to improper behaviour on the part of the user, or which are connected with such operation<br />
in any way. Unless otherwise prescribed by binding law, the obligation of GRAUPNER to pay compensation<br />
for any reason whatsoever (including personal injury, death, damage to buildings, damage due to loss of<br />
business or turnover, interruption of business, or other direct or indirect consequent damage) stemming from<br />
the operation of the model is excluded.<br />
The total liability in all cases and under all circumstances is limited to the amount of money that you actually<br />
paid for this model.<br />
This model is started up and operated at the sole and exclusive risk of the operator.<br />
To avoid injuring people and damaging property, it is essential to be careful and thoughtful when<br />
operating your model.<br />
Before operating the model for the first time, check whether the operation of model ships of this kind is covered<br />
by your private liability insurance. If necessary, purchase a special RC model liability insurance policy.<br />
These safety notes must be retained and provided to the buyer if sold to another person.<br />
The following items must be observed:<br />
• The model is not suitable for children under 14 years old.<br />
• Because of the high speed, never operate the model when people or animals are in the water, because<br />
this represents a great danger of injury to them.<br />
• Do not operate your model in nature preserves, landscape protection areas, or water conservation districts.<br />
Find out from your local government which waters are approved for model shipbuilders.<br />
• Never operate the model in salt water.<br />
• Never operate the model in adverse weather conditions, such as rain, thunderstorm, strong wind, or in<br />
high waves or strong currents, et cetera.<br />
• Before you fly the model, check that the radio control system is working reliably, and that all connections<br />
are safe and secure.<br />
• Observe the operating information on the installed remote control system and accessories.<br />
• Ensure that the channel you intend to use is not already in use. Never operate the model if you are not<br />
certain that your channel is free.<br />
• Work on the parts of the drive system only with the motor power supply disconnected.<br />
• When the drive battery is connected, you and other persons must never get near the ship's propeller,<br />
because it poses a substantial risk of injury.<br />
• Do not exceed the recommended operating voltage. A higher voltage can lead to overheating of the mo-<br />
GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY<br />
Not liable for printing errors. We reserve the right to make technical modifications. 11/2011 2
tor or speed controller or cause electrical lines to melt. This can cause the model to be destroyed or<br />
catch fire.<br />
• Make sure all drive components can move freely. This applies especially during operations, because<br />
leaves and other things can get caught in the drive mechanism. In such a case, the motor, the speed<br />
controller, or the rudder servo can be destroyed by an overload.<br />
• Never leave the battery to charge unattended. Observe the instructions for the charger and battery.<br />
• When using a car charger, always charge the battery outside the car.<br />
• Ensure that the servos are not mechanically obstructed at any point in their travel.<br />
• The batteries and rechargeable batteries may not be short-circuited or be exposed to direct contact with<br />
water.<br />
• Let the motor and the speed controller cool off after each trip. Do not touch the hot parts.<br />
• Do not subject the model to intense humidity, heat, cold, vibrations, or dirt.<br />
• When storing the model, remove the rechargeable batteries / batteries and store them so that they can<br />
not be short-circuited.<br />
• The drive battery must always be removed when transporting the model.<br />
• Protect the model, batteries, and RC components against damage and slipping during transport.<br />
• Always make sure that the sheet metal contacts between the RC box and the drive motor are insulated;<br />
never let them come into electrical contact.<br />
• When the model begins to slow down, the drive battery is nearly empty. Sail immediately to shore and<br />
stop operating the model. Before a new trip, the battery must be recharged.<br />
• If you operate the model in moving water (such as a river) be aware that the model can drift away if there<br />
is a malfunction or if the battery runs down.<br />
• When trying to retrieve the model, never put yourself or others in danger.<br />
• Take particular care to ensure that the model is watertight. A model boat can sink if enough water gets<br />
in. Check the model before each trip to see whether there is any damage and whether water can penetrate<br />
through the drive and rudder shafts. In particular, check the rubber seals on the model. The RC box<br />
should also be closed, to ensure that no water can splash in from above. Water damage is not covered<br />
by warranty!<br />
• Secure the cover by inserting the splint through the hole in the mount.<br />
Care and maintenance<br />
• Clean the model carefully after each use. Immediately remove any water that has penetrated using a<br />
dishtowel or something similar. Always leave the cover open for a longer period of time to allow the residual<br />
moisture to dry out.<br />
• Clean the model and the RC components using suitable cleaning agents only. Ask your model shop for<br />
information.<br />
• Lubricate the shaft regularly. Your retailer can provide you with information about suitable types of waterneutral<br />
grease.<br />
• If the model is not to be operated for a considerable time, all the moving parts (shaft, et cetera) must be<br />
disassembled, cleaned, and re-lubricated. All rechargeable and other batteries should also be removed<br />
from the model and transmitter and stored separately.<br />
GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY<br />
Not liable for printing errors. We reserve the right to make technical modifications. 11/2011 3
Important safety and operating information for the RC system<br />
• Always switch the transmitter on first; then switch on the receiver (model)!<br />
• Always switch the receiver off first; then switch off the transmitter!<br />
• Protect all equipment against dust, dirt, humidity, vibrations, and other foreign objects. Never expose the<br />
equipment to excessive heat or cold.<br />
• Avoid impacts and pressure. Always check the equipment for damage to housings and cables.<br />
• Never pull on cables to disconnect them.<br />
• Avoid incorrect polarity and short-circuits of all kinds as well as excess voltage in the power supply. The<br />
devices are not protected against these hazards.<br />
• Use only components specified and approved by GRAUPNER.<br />
• GRAUPNER recommends using only dry cell batteries for the transmitter power supply. Use rechargeable<br />
batteries in this area at your own risk!<br />
• Never use batteries with different energy states (meaning full in combination with empty batteries) or<br />
different types or manufacturers.<br />
• Dry cell batteries for the power supply may never be recharged. Only rechargeable batteries can be recharged.<br />
• The batteries must be adequately charged, and the range of the radio control system must have been<br />
checked. In case of doubt and for the sake of safety, the transmitter and receiver batteries should be replaced<br />
if the state of the batteries is unknown.<br />
• During operations, the transmitter aerial must be securely installed and completely extended.<br />
• Run the receiver aerial only as designed for the model. It should be as far as possible away from power<br />
cables.<br />
• If water has penetrated the RC components, lay them out to dry and send them to the appropriate<br />
GRAUPNER service unit to be checked (see list of responsible service centres at the end of the instructions).<br />
GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY<br />
Not liable for printing errors. We reserve the right to make technical modifications. 11/2011 4
Assembly and operating instructions<br />
Assembly of the propeller<br />
Place the propeller on the shaft and screw it on using the drive dog nut.<br />
Assembly of the rudder<br />
Shove the rudder lever (1) into the hole in the rudder, and fasten the rudder in opening provided by inserting<br />
the metal pin (2) into the opening from above. When everything is fastened, tighten from the other side using<br />
the grub screw.<br />
GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY<br />
Not liable for printing errors. We reserve the right to make technical modifications. 11/2011 5
Final assembly of the rudder<br />
Take the rudder linkage and run it through the rudder mount; let the rudder linkage stick out about 8 to 12<br />
mm; cut off the remaining part of the rudder linkage using pliers. Fasten the rudder linkage by screwing in a<br />
3x3 grub screw.<br />
Connecting the water cooling unit<br />
Place the water cooling tube over the connector located on the top of the rudder; make sure it is tight.<br />
GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY<br />
Not liable for printing errors. We reserve the right to make technical modifications. 11/2011 6
Assembly of the boot stand<br />
Install the boot stand in the sequence illustrated in the drawing. To do so, use fast-setting glue or casein<br />
glue.<br />
6. Inserting the battery<br />
Place the battery into the loops provided in the boat. Make sure to use ONLY a maximum 11.1 V 2100-<br />
4500mAh Lipo.<br />
GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY<br />
Not liable for printing errors. We reserve the right to make technical modifications. 11/2011 7
Inserting the receiver<br />
Connect the receiver as per the operating instructions. Be sure you NEVER operate the model if your radio<br />
control system or receiver is not working properly.<br />
When everything is working properly, you can charge the battery and start your maiden voyage with your<br />
model.<br />
Before each trip, make sure that the water cooling tubes are connected.<br />
Water in the RC system can destroy the controller and the receiver. The lateral exit point for the cooling water<br />
and the connections of the motor cooling loop should also be checked before each trip.<br />
Important: Make sure that the motor connector cable is not located in the area of the motor coupling.<br />
Tape the model along the cover to keep water from getting in.<br />
GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY<br />
Not liable for printing errors. We reserve the right to make technical modifications. 11/2011 8
Trimming the model<br />
The two Allen bolts on the left side of the shaft need to be loosened and the angle of the drive mechanism<br />
adjusted. In case of waves or strong wind, tilting the drive mechanism down pushes the bow down while<br />
cruising to reduce or even completely prevent hopping.<br />
After making the adjustments, retighten the bolts.<br />
The batteries can also be moved fore or aft.<br />
After each trip, check for any water penetration and remove it.<br />
In particular, any batteries that have gotten wet must be removed from the model and dried.<br />
Maiden voyage<br />
Charge the batteries, and test the functions of the model. Secure the cover with tape, so that it can not fall<br />
down and so that no water can get into the model. Now you can start the maiden voyage.<br />
During the maiden voyage, start slowly; first get familiar with the sailing behaviour. Test the steering behaviour,<br />
stopping distance, and range.<br />
If the model begins to "hop" when running fast, change the position of the drive mechanism until the model<br />
runs smoothly again, or move the batteries forward.<br />
Have fun running your model Watercutter<br />
GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY<br />
Not liable for printing errors. We reserve the right to make technical modifications. 11/2011 9
Spare parts<br />
Order No. Designation<br />
2203.1 Propeller<br />
2202.1 Motor<br />
2202.2 Controller<br />
Accessories (not included in delivery)<br />
9745.3 LiPo-Akku V-MAXX 45C 3/4500 11,1V G3,5<br />
33116 MX-16 Computer System 8-Channel Gr. HoTT<br />
or<br />
33112 MX-12 Computer System 6-Channel Gr. HoTT<br />
Optional accessories (not included in delivery)<br />
6466 Charger Ultra Trio plus 14 (for drive battery, transmitter battery), mains and car battery operation<br />
Notes on environmental protection<br />
Disposal<br />
Electronic and electrical products may not be placed in the rubbish.<br />
Dispose of the product at the end of its useful life in accordance with applicable legal regulations.<br />
GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY<br />
Not liable for printing errors. We reserve the right to make technical modifications. 11/2011 10
Service<br />
Germany / Austria<br />
<strong>Graupner</strong> GmbH & Co. KG<br />
Postfach 1242<br />
D-73220 Kirchheim / Teck<br />
(+49) 18 05 / 47 28 76<br />
Czech Republic / Slovene Republic<br />
RC Service Z. Hnizdil<br />
Letecka 666/22<br />
CZ 16100 Prague 6 – Ruzyne<br />
(+42) 23 33 13 09 5<br />
FAX (+42) 23 33 13 09 5<br />
France<br />
<strong>Graupner</strong> France<br />
Gérald Altmayer<br />
86, rue St. Antoine<br />
F 57601 Forbach-Oeting<br />
(+33) 38 78 56 21 2<br />
FAX (+33) 38 78 50 00 8<br />
Luxembourg<br />
Kit Flammang<br />
129, Route d’Arlon<br />
L 8009 Strassen<br />
(+35) 23 12 23 2<br />
FAX (+35) 23 13 04 9<br />
Sweden<br />
Baltechno Electronics<br />
P.O. Box 5307<br />
S 40227 Göteborg<br />
(+46) 31 70 73 00 0<br />
FAX (+46) 31 70 73 00 0<br />
Germany / Austria<br />
<strong>Graupner</strong> GmbH & Co. KG<br />
Postfach 1242<br />
D-73220 Kirchheim / Teck<br />
(+49) 18 05 / 47 28 76<br />
Czech Republic / Slovene Republic<br />
RC Service Z. Hnizdil<br />
Letecka 666/22<br />
CZ 16100 Praha 6 – Ruzyne<br />
(+42) 23 33 13 09 5<br />
FAX (+42) 23 33 13 09 5<br />
France<br />
<strong>Graupner</strong> France<br />
Gérald Altmayer<br />
86, rue St. Antoine<br />
F 57601 Forbach-Oeting<br />
(+33) 38 78 56 21 2<br />
FAX (+33) 38 78 50 00 8<br />
Luxembourg<br />
Kit Flammang<br />
129, Route d’Arlon<br />
L 8009 Strassen<br />
(+35) 23 12 23 2<br />
FAX (+35) 23 13 04 9<br />
Sweden<br />
Baltechno Electronics<br />
P.O. Box 5307<br />
S 40227 Göteborg<br />
(+46) 31 70 73 00 0<br />
FAX (+46) 31 70 73 00 0<br />
Belgium / Netherlands<br />
Jan van Mouwerik<br />
Slot de Houvelaan 30<br />
NL 3155 Maasland VT<br />
(+31) 10 59 13 59 4<br />
FAX (+31) 31 10 59 13 59 4<br />
Spain<br />
Anguera Hobbies<br />
C/Terrassa 14<br />
E 43206 Reus (Tarragona)<br />
Tel. (+34) 97 77 55 32 0<br />
FAX (+34) 97 77 74 96 8<br />
Italy<br />
GiMax<br />
Via Manzoni, no. 8<br />
I 25064 Gussago<br />
(+39) 30 25 22 73 2<br />
FAX (+39) 30 25 22 71 1<br />
Switzerland<br />
<strong>Graupner</strong> Service CD-Electronics GmbH<br />
Kirchweg 18<br />
CH-5614 Sarmenstorf<br />
(+41) 56 667 14 91<br />
United Kingdom<br />
Gliders<br />
Brunel Drive<br />
GB Newark, Nottinghamshire NG242EG<br />
(+44) 16 36 61 05 39<br />
FAX (+44) 16 36 60 52 55<br />
Belgium / Netherlands<br />
Jan van Mouwerik<br />
Slot de Houvelaan 30<br />
NL 3155 Maasland VT<br />
(+31) 10 59 13 59 4<br />
FAX (+31) 31 10 59 13 59 4<br />
Spain<br />
FA-Sol S.A.<br />
C. Avinyo 4 (Pujada Roja)<br />
E 8240 Manresa<br />
(+34) 93 87 34 23 4<br />
FAX (+34) 93 87 41 55 4<br />
Italy<br />
GiMax<br />
Via Manzoni, no. 8<br />
I 25064 Gussago<br />
(+39) 30 25 22 73 2<br />
FAX (+39) 30 25 22 71 1<br />
Switzerland<br />
<strong>Graupner</strong> Service<br />
Postfach 92<br />
CH 8423 Embrach-Embraport<br />
(+41) 43 26 66 58 3<br />
FAX (+41) 43 26 66 58 3<br />
United Kingdom<br />
<strong>Graupner</strong> Service UK<br />
Brunel Drive<br />
GB Newark, Nottinghamshire NG242EG<br />
(+44) 16 36 61 05 39<br />
FAX (+44) 16 36 60 52 55<br />
GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY<br />
Not liable for printing errors. We reserve the right to make technical modifications. 11/2011 11
Change language