manual MAPV2 eng - Audionet
manual MAPV2 eng - Audionet manual MAPV2 eng - Audionet
Connection diagram RGB video output with C-Sync: If your video display has a video input for progressive RGB video signals with C-Sync (= Composite Sync), connect the MAP V2 according to the following diagram: This unit must be earthed. VGA OUT RGB + C-Sync OUT OUT OUT Y/R C /G C /B R B IN IN IN IN 1 Audionet EPS only. 46 IN 2 IN 3 IN 4 VIDEO IN NEG. OUT 1 OUT 2 VIDEO OUT (OSD) S-VIDEO 1 S-VIDEO 2 S-VIDEO 3 S-VIDEO 4 S-VIDEO 1 S-VIDEO 2 (Vsync) ANALOG OUTPUTS R G B C-Sync to video input of video display (4x Cinch) VGA alternative connection to video input of video display (VGA) Pinning: Pin #1 = R Pin #2 = G Pin #3 = B Pin #13 = C-Sync (Hsync) OPTICAL DIGITAL OUT Note: • Please make sure, that for this video output mode the function Set Video Out is set to C-Sync to provide the correct Sync signals at video output OUT2 7 (see above 'Video outputs Progressive Scan Card'). left
Connection diagram RGB video output H/V-Sync: If your video display has a video input for progressive RGB video signals with separate H-Sync/V-Sync signals, connect the MAP V2 according to the following diagram: This unit must be earthed. VGA OUT RGB + C-Sync OUT OUT OUT Y/R C /G C /B R B IN IN IN IN 1 Audionet EPS only. 47 IN 2 IN 3 IN 4 VIDEO IN NEG. OUT 1 OUT 2 VIDEO OUT (OSD) S-VIDEO 1 S-VIDEO 2 S-VIDEO 3 S-VIDEO 4 S-VIDEO 1 S-VIDEO 2 (Vsync) ANALOG OUTPUTS R G B V-Sync H-Sync to video input of video display (5x Cinch) VGA alternative connection to video input of video display (VGA) Pinning: Pin #1 = R Pin #2 = G Pin #3 = B Pin #13 = H-Sync Pin #14 = V-Sync (Hsync) OPTICAL DIGITAL OUT Note: • Please make sure, that for this video output mode the function Set Video Out is set to option H/V-Sync to provide separate Sync signals on video outputs OUT1 and OUT2 7 (see above 'Video outputs Progressive Scan Card'). left monitor
- Page 1: Multi Channel Audio/Video Pre - Amp
- Page 4 and 5: Overview Connections 4
- Page 6 and 7: Additional earth connection Optiona
- Page 8 and 9: External 8-Channel Analog Inputs: P
- Page 10 and 11: dependent level settings. To save t
- Page 12 and 13: Audionet System Remote Control Harm
- Page 14 and 15: Key assignment MAP V2 1 3 5 7 Fri 1
- Page 16 and 17: 8 Skips back to the previous screen
- Page 18 and 19: PCM Direct off. PCM Direct mode can
- Page 20 and 21: Screen page 5 Fri 12:45 MAP V2 1 Se
- Page 22 and 23: Screen page 6 Fri 12:45 MAP V2 1 Se
- Page 24 and 25: Screen page 8 Fri 12:45 MAP V2 Q- Q
- Page 26 and 27: Setup Description of all menu items
- Page 28 and 29: Menu Channel Setup This menu compri
- Page 30 and 31: Edit Channel Name: While in menu Ch
- Page 32 and 33: Note: • This menu item is only av
- Page 34 and 35: Use buffered input, if the output i
- Page 36 and 37: eproduce the bass of this group, an
- Page 38 and 39: Display While in RUN mode the first
- Page 40 and 41: PCM input signal information about
- Page 42 and 43: Progressive Scan Card The optional
- Page 44 and 45: Note: • Many units use a SCART co
- Page 48 and 49: Connection diagram RGB video output
- Page 50 and 51: Security advice ♦ Avoid packaging
Connection diagram RGB video output H/V-Sync:<br />
If your video display has a video input for progressive RGB video signals with separate<br />
H-Sync/V-Sync signals, connect the MAP V2 according to the following diagram:<br />
This unit must be earthed.<br />
VGA<br />
OUT<br />
RGB + C-Sync<br />
OUT OUT OUT<br />
Y/R C /G C /B<br />
R B<br />
IN IN IN<br />
IN 1<br />
<strong>Audionet</strong> EPS only.<br />
47<br />
IN 2 IN 3 IN 4<br />
VIDEO IN<br />
NEG.<br />
OUT 1 OUT 2<br />
VIDEO OUT<br />
(OSD)<br />
S-VIDEO 1 S-VIDEO 2 S-VIDEO 3 S-VIDEO 4 S-VIDEO 1 S-VIDEO 2<br />
(Vsync)<br />
ANALOG OUTPUTS<br />
R G B V-Sync H-Sync<br />
to video input of video display (5x Cinch)<br />
VGA<br />
alternative connection to video input<br />
of video display (VGA)<br />
Pinning: Pin #1 = R<br />
Pin #2 = G<br />
Pin #3 = B<br />
Pin #13 = H-Sync<br />
Pin #14 = V-Sync<br />
(Hsync)<br />
OPTICAL<br />
DIGITAL<br />
OUT<br />
Note:<br />
• Please make sure, that for this video output mode the function Set Video Out is<br />
set to option H/V-Sync to provide separate Sync signals on video outputs OUT1<br />
and OUT2 7 (see above 'Video outputs Progressive Scan Card').<br />
left<br />
monitor