manual MAPV2 eng - Audionet
manual MAPV2 eng - Audionet manual MAPV2 eng - Audionet
Screen page 6 Fri 12:45 MAP V2 1 Setup Manager 2 Video 5 Test Tone 6 8 Channel Global Setup 3 4 Setup 6 OF 9 1 Channel Setup enters the Channel Setup menu. 2 Global Setup enters the Global Setup menu. 3 Video Setup enters the Video Setup menu. 4 Bass Manager enters the Bass Manager menu. 5 Delay Manager enters the Delay Manager menu. 6 Press key TestTone to start the internal test tone generator. The generator delivers a noise signal to the Front Left channel. You can now adjust the reference level with keys Vol- / Vol+ as described above. Press key Ch- to produce the noise signal in the next channel. Or use key Ch+ to skip back to the previous channel. Ch- moves the noise signal clockwise (according to your speaker positions in your listening room) from one channel to the other, Ch+ selects the channels anti clockwise. Adjust the level of each selected channel so that all channels reproduce the noise signal of the test tone generator with the same volume. Press TestTone again to switch off the test tone generator and return to RUN mode. Note: No test tone is available on the Subwoofer output! 7 Number of current screen page and total number of pages (example: '6 OF 9' → screen page 6 of 9). 8 Skips back to the previous screen page (see user's manual Harmony 785). 9 Advances to the next screen page (see user's manual Harmony 785). For further details on the setup menus please refer to section 'Setup'. Screen page 7 All 8 keys on screen pages 7 and 8 are used to configure the parametric, digital equalizer. If the MAP V2 is in any other mode than the setup mode for the equalizer, 22 Bass Delay Manager 7 9
pressing one of the 8 keys invokes the setup mode for the equalizer. Then the keys have the following functions: Key Ch- selects the next channel, key Ch+ the previous channel. While in the equalizer setup mode you are still able to adjust the master volume using keys Vol- / Vol+ . Leave the equalizer setup mode by using one of the other setup menu keys. The MAP V2 then enters the corresponding menu. If you wait for approx. 12 seconds without pressing any key, the MAP V2 will return to RUN mode automatically. 1 MPE- selects the previous MPE *) filter of the current channel. 2 MPE+ selects the next MPE filter of the current channel. 3 Freq- decreases the center frequency of the current MPE filter. 4 Freq+ increases the center frequency of the current MPE filter. 5 Number of current screen page and total number of pages (example: '7 OF 9' → screen page 7 of 9). 6 Skips back to the previous screen page (see user's manual Harmony 785). 7 Advances to the next screen page (see user's manual Harmony 785). *) MPE = Minimum Phase Equalizer Fri 12:45 MAP V2 5 Freq- Freq+ 6 8 MPE- MPE+ 3 4 7 OF 9 23 7 9
- Page 1: Multi Channel Audio/Video Pre - Amp
- Page 4 and 5: Overview Connections 4
- Page 6 and 7: Additional earth connection Optiona
- Page 8 and 9: External 8-Channel Analog Inputs: P
- Page 10 and 11: dependent level settings. To save t
- Page 12 and 13: Audionet System Remote Control Harm
- Page 14 and 15: Key assignment MAP V2 1 3 5 7 Fri 1
- Page 16 and 17: 8 Skips back to the previous screen
- Page 18 and 19: PCM Direct off. PCM Direct mode can
- Page 20 and 21: Screen page 5 Fri 12:45 MAP V2 1 Se
- Page 24 and 25: Screen page 8 Fri 12:45 MAP V2 Q- Q
- Page 26 and 27: Setup Description of all menu items
- Page 28 and 29: Menu Channel Setup This menu compri
- Page 30 and 31: Edit Channel Name: While in menu Ch
- Page 32 and 33: Note: • This menu item is only av
- Page 34 and 35: Use buffered input, if the output i
- Page 36 and 37: eproduce the bass of this group, an
- Page 38 and 39: Display While in RUN mode the first
- Page 40 and 41: PCM input signal information about
- Page 42 and 43: Progressive Scan Card The optional
- Page 44 and 45: Note: • Many units use a SCART co
- Page 46 and 47: Connection diagram RGB video output
- Page 48 and 49: Connection diagram RGB video output
- Page 50 and 51: Security advice ♦ Avoid packaging
pressing one of the 8 keys invokes the setup mode for the equalizer. Then the keys have<br />
the following functions:<br />
Key Ch- selects the next channel, key Ch+ the previous channel. While in the<br />
equalizer setup mode you are still able to adjust the master volume using keys Vol- /<br />
Vol+ .<br />
Leave the equalizer setup mode by using one of the other setup menu keys. The<br />
MAP V2 then enters the corresponding menu. If you wait for approx. 12 seconds<br />
without pressing any key, the MAP V2 will return to RUN mode automatically.<br />
1 MPE- selects the previous MPE *) filter of the current channel.<br />
2 MPE+ selects the next MPE filter of the current channel.<br />
3 Freq- decreases the center frequency of the current MPE filter.<br />
4 Freq+ increases the center frequency of the current MPE filter.<br />
5 Number of current screen page and total number of pages<br />
(example: '7 OF 9' → screen page 7 of 9).<br />
6 Skips back to the previous screen page (see user's <strong>manual</strong> Harmony 785).<br />
7 Advances to the next screen page (see user's <strong>manual</strong> Harmony 785).<br />
*) MPE = Minimum Phase Equalizer<br />
Fri 12:45<br />
MAP V2<br />
5 Freq-<br />
Freq+<br />
6<br />
8<br />
MPE-<br />
MPE+<br />
3 4<br />
7 OF 9 <br />
23<br />
7<br />
9