manual MAP1 en - Audionet
manual MAP1 en - Audionet manual MAP1 en - Audionet
Menu Channel Setup This menu comprises all settings, that are valid only for the current selected input channel. If you change the input channel, all settings are saved automatically and the channel settings for the new channel are loaded. Therefore, you can adjust the MAP 1 to each connected source independently, and don't have to worry about saving and reloading the settings you made. The MAP 1 will do the work automatically. Internal Decoder: In order to switch off the internal decoder, press key Vol- (the display shows pure 2-channnel). All program material is downmixed to 2-ch Stereo independently from the original program format. Dolby Pro Logic IIx or DTS Neo:6 decoding, bass and delay management are off in this mode. It is strongly recommended to use this mode for Stereo PCM or 2-channel analog sources only. Press key Vol+ to activate the internal decoder (the display shows Multi- Channel). All incoming program formats (PCM or bitstream) are detected and decoded automatically (see also section 'PCM direct'). Note: • The internal decoder can be activated for all audio inputs except the external 8channel analog input (External 8ch). • If the internal decoder is active for a 2-channel analog audio input, the input signals are internally converted from analog to digital. Now all functions like Dolby Pro Logic IIx or DTS Neo:6 decoding, bass and delay management, digital equalizer etc are available as for any digital audio input. • The internal analog to digital converter has an input sensitivity of 2 VRMS. If input signals exceed this level, the converter will overload causing audible distortions. In this case, reduce the output level of the unit connected to the MAP 1 until no overload occurs. Set Video Input: You can assign one of the video inputs (2 cinch video inputs 4 , 2 S-Video inputs 15 , 1 DVI input 3 , 1 alternative YUV/RGB input) to each input channel independently. Even multiple assignments are allowed (e.g. for connecting a DVD player that uses more than one audio output). If no video input is needed for an audio input, please select No Video Input. No Video Input No video input is selected. Video In1 or In2 The corresponding video input IN1 or IN2 4 is selected. S-Video In1 or In2 The corresponding S-Video input S-VIDEO IN1 or S-VIDEO IN2 15 is selected. DVI-Int. In The video input 3 is used for analog and digital DVI signals (DVI-I) which are routed directly to the DVI output 16 . Cinch Analog The video inputs 4 and video output 5 are re-defined in their function to be used for component video input. 28
Their analog signals are routed directly to the analog part of DVI output 16 . Note: • If you assign any of the Cinch (or Composite) video inputs 4 to an audio input, you will have a video signal at the Cinch/Composite video output 5 as well as at the S-Video output 14 (automatically converted by the internal 'Cinch-to-S-Video Converter'). • If the optional Progressive Scan Card is inserted, some more video inputs and options are available. In this case, please refer to chapter 'Progressive Scan Card' for more detailed information. • This menu item is located in the menu Channel Setup, as it is a setting, that can be selected for each input channel independently. Although the menu Video Setup deals with global video settings, the same function Set Video Input, as described above, is also integrated into the Video Setup menu, simply for an easier access. • For each audio input the corresponding video input is assigned individually. To simplify this procedure, select the desired video input for each audio input during the setup (of channel levels, names, decoder settings etc) for this audio input. Offset Adjust: Use Vol- and Vol+ keys to adjust the input channel offset. You can add gain or attenuate each input channel individually within a range of +9...-9dB in order to compensate different output levels of sources connected to the MAP 1. Set Listening Mode: This menu item has the same function as the key Listening Mode on the remote control described above. Digital Filter: This menu item has the same function as the key Digital Filter on the remote control described above. Dynamic Range: This menu item has the same function as the key Dynamic Range of the remote control described above. Set Dual Mono: Select the preferred playback mode for DVD soundtracks in Dual Mono mode with the Vol- and Vol+ keys. CH1+CH2: Both Dual Mono channels are reproduced CH1 only:: Only Dual Mono channel 1 is reproduced CH2 only: Only Dual Mono channel 2 is reproduced Note: • This menu is only available, if Internal Decoder is set to Multi-Channel. 29
- Page 1: Multi Channel Audio/Video Pre - Amp
- Page 4 and 5: Placement and connection Important:
- Page 6 and 7: Overview of connections 7 Digital i
- Page 8 and 9: (refer to owner's manual of VIP), t
- Page 10 and 11: configured. Your MAP 1 needs inform
- Page 12 and 13: Overview of menu structure RUN Mode
- Page 14 and 15: 5 Activities key: Press this key to
- Page 16 and 17: 3 Vol+ , increases the volume of th
- Page 18 and 19: Screen page 3 MAP 1: 3/9 pages Curr
- Page 20 and 21: If this reference level is set corr
- Page 22 and 23: to the names of the other user sett
- Page 24 and 25: Leave the equalizer setup mode by u
- Page 26 and 27: Setup Description of all menu items
- Page 30 and 31: Edit Channel Name: While in menu Ch
- Page 32 and 33: Note: • This menu item is only av
- Page 34 and 35: Note: • This setting refers to Li
- Page 36 and 37: Subwoofer: If a subwoofer is availa
- Page 38 and 39: Display While in RUN mode the 2 nd
- Page 40 and 41: On the left of the 2 nd line the pr
- Page 42 and 43: On Screen Display (OSD) Activate th
- Page 44 and 45: setting for digital and analog DVI
- Page 46 and 47: Note: • If the optional DVI Modul
- Page 48 and 49: Settings for analog RGB-video outpu
- Page 50 and 51: USB Audio With the USB Audio interf
- Page 52 and 53: • The USB Audio input of the MAP
- Page 54 and 55: Security advice • Avoid packaging
M<strong>en</strong>u Channel Setup<br />
This m<strong>en</strong>u comprises all settings, that are valid only for the curr<strong>en</strong>t selected input<br />
channel. If you change the input channel, all settings are saved automatically and the<br />
channel settings for the new channel are loaded. Therefore, you can adjust the MAP 1 to<br />
each connected source indep<strong>en</strong>d<strong>en</strong>tly, and don't have to worry about saving and reloading<br />
the settings you made. The MAP 1 will do the work automatically.<br />
Internal Decoder:<br />
In order to switch off the internal decoder, press key Vol- (the display shows pure<br />
2-channnel). All program material is downmixed to 2-ch Stereo indep<strong>en</strong>d<strong>en</strong>tly from<br />
the original program format. Dolby Pro Logic IIx or DTS Neo:6 decoding, bass and<br />
delay managem<strong>en</strong>t are off in this mode. It is strongly recomm<strong>en</strong>ded to use this mode for<br />
Stereo PCM or 2-channel analog sources only.<br />
Press key Vol+ to activate the internal decoder (the display shows Multi-<br />
Channel). All incoming program formats (PCM or bitstream) are detected and<br />
decoded automatically (see also section 'PCM direct').<br />
Note:<br />
• The internal decoder can be activated for all audio inputs except the external 8channel<br />
analog input (External 8ch).<br />
• If the internal decoder is active for a 2-channel analog audio input, the input signals<br />
are internally converted from analog to digital. Now all functions like Dolby Pro<br />
Logic IIx or DTS Neo:6 decoding, bass and delay managem<strong>en</strong>t, digital equalizer etc<br />
are available as for any digital audio input.<br />
• The internal analog to digital converter has an input s<strong>en</strong>sitivity of 2 VRMS. If input<br />
signals exceed this level, the converter will overload causing audible distortions. In<br />
this case, reduce the output level of the unit connected to the MAP 1 until no<br />
overload occurs.<br />
Set Video Input:<br />
You can assign one of the video inputs (2 cinch video inputs 4 , 2 S-Video inputs 15 ,<br />
1 DVI input 3 , 1 alternative YUV/RGB input) to each input channel indep<strong>en</strong>d<strong>en</strong>tly.<br />
Ev<strong>en</strong> multiple assignm<strong>en</strong>ts are allowed (e.g. for connecting a DVD player that uses<br />
more than one audio output). If no video input is needed for an audio input, please<br />
select No Video Input.<br />
No Video Input No video input is selected.<br />
Video In1 or In2 The corresponding video input IN1 or IN2 4 is selected.<br />
S-Video In1 or In2 The corresponding S-Video input S-VIDEO IN1 or<br />
S-VIDEO IN2 15 is selected.<br />
DVI-Int. In The video input 3 is used for analog and digital DVI<br />
signals (DVI-I) which are routed directly to the DVI<br />
output 16 .<br />
Cinch Analog The video inputs 4 and video output 5 are re-defined<br />
in their function to be used for compon<strong>en</strong>t video input.<br />
28
Change language