Industrial Power Tools 2010-11 - Atlas Copco

More documents

Recommendations

Info

ErgoPulse impulse tools – fast, reliable and operator friendly Introduction – ErgoPulse The speed, reliability, and accuracy of ErgoPulse hydraulic impulse nutrunners, combined with the fact that they are comfortable to operate, make them suitable for continuous heavy production. Since there is no metal-to-metal impact in a pulse tool, it provides a softer, more controlled pulse with considerably less vibration and noise than an impact wrench. A complete range ErgoPulse impulse tools are available in straight and pistol grip, shut-off and non shut-off versions. The range covers torque from 2–900 Nm. The ErgoPulse principle – The heart of a pulse tool is the hydraulic pulse unit. Since the pulses are very short, there is almost no reaction force in the handle, only the much lower motor torque is transferred to the operator’s hand. In addition, there are less vibrations and noise than with an impact wrench. Combined with good balance and low weight the result is a tool that is very comfortable to operate. PTS and PTX shut-off pulse tools Atlas Copco shut-off pulse tools shut off the air supply when the pre-set torque is been reached. Operator influence is minimized and the result is increased accuracy and faster tightening. Torque sensing system – In ErgoPulse PTS and PTX nutrunners torque is “sensed” by means of a rotatable inertial mass acting against an adjustable spring. The result is a highly accurate and easily adjustable shut-off system. Pulse mechanism – The pulse mechanism has pistons for minimum weight and long service life. The design is based on cam-guided pistons and rollers and the pulse cylinder is oil-filled. The moving parts are thus completely immersed in oil, which ensures a long service life. Twin chamber vane motor – This is designed to give high torque at low speed, which gives the best characteristics for fast, accurate tightening. TRIM valve – A patented adjustable valve at the air outlet is used to maximize tool accuracy on one type of joint, which could be hard, medium or soft. AUTOTRIM valve – PTS/PTX-AT tools are equipped with an automatic twostage trim valve. The tool runs down the screw with reduced free speed. After 1-2 pulses it shifts automatically to full power thus enabling both hard and soft joints to be tightened with excellent results with- out any adjustments. The PTS/PTX-AT tools can also be used for reporting applications. ErgoPulse PTS-HRF – These are Air-on-Top versions which offer full flexibility. You either use the air inlet on top to avoid the disturbing hose hook or you use the conventional air inlet at the bottom of the handle – a convenient tool for use in workstations. ErgoPulse PTX – The new ErgoPulse PTX series is intended for applications where weight is critical. The tools are available in both Trim and AutoTrim versions. ErgoPulse 25PTX At the top of the PTX range, is the new ErgoPulse 25PTX, which gives you 900 Nm of tightening torque in a tool weighing only 10.3 kg. ErgoPulse XS non shut-off tools ErgoPulse XS is the correct choice when the operator needs to control the process. The tools provide high torque, fast, accurate tightening and long service lifetimes. Twin chamber vane motor – This is designed to give high torque at low speed, which provides the best characteristics for fast, reliable and accurate tightening. Double or triple bladed pulse mechanisms – The tools are equipped with pulse units with two or three blades. They employ the Atlas Copco patented cam-guided design to push out the blades, giving very high reliability. The pulse units have a high power-to-weight ratio, making the tools very powerful for their size. Torque is adjusted by regulating an artificial leak in the hydraulic circuit. ErgoPulse 6PS This model is a good choice for tightening self-tapping screws and when fast, powerful reversing is needed. Torque is adjusted by regulating the air pressure. Pneumatic Assembly Tools 33 Hydraulic Impulse Nutrunners
Hydraulic Impulse Nutrunners Selection Guide EP PTS/PTX Shut-off models The ErgoPulse PTS and PTX tools can be adjusted within a wide torque range by simply setting the spring force that counteracts the inertia body. Torque should preferably be checked with a hand torque wrench. Electronic monitoring with an in-line transducer is possible but should be verified with a manual hand torque wrench to avoid measuring errors due to the extremely short pulse sequence. Torque Nm M27 M24 M20 M16 M14 M12 M10 M8 M6 M5 8.8 19 9* 31 13* 45 22* 34 Pneumatic Assembly Tools 9 4* 14 8* 19 8* 22 10* 32 16 35 18* 3PTX 4PTX 5PTX 7PTX 6PTX 8PTX 3PTX 4PTX 5PTS 5PTX 6PTS 7PTS 8PTS 6PTX 7PTX 8PTX 9PTX 11PTX 13PTX 15PTX 19PTX 10PTS 12PTS 14PTS 18PTS 25PTX * For tools with quick change chuck, see technical data. M20 M16 M14 M12 M10 M8 M6 M5 M4 5 2* Straight Pistol grip models models 9 15 6* 4* 3/8" square drive 8.8 Screw size EP XS/PS Non shut-off models Torque Nm 5 2* Straight models Pistol grip models 20 10* 31 20* 52 30* 20 10* 55 30 55 30* 70 40 52 30* 80 50 70 50 90 50 110 70 110 65 150 3/8" square drive 1/2" square drive 12 5 28 6XS 7XS 8XS 5XS 6PS 6XS 7XS 8XS 10XS 12XS 14XS 16XS 20XS * For tools with quick change chuck, see technical data. 31 20* 85 160 110 150 85 250 125 240 160 250 125 400 300 410 225 3/4" square drive The size of tool is determined on the basis of torque and/or bolt dimension. Torque should preferably be checked with a hand torque wrench. Electronic monitoring with an in-line transducer is possible but should be verified with a manual hand torque wrench to avoid measuring errors due to the extremely short pulse sequence. Screw size 3/8" square drive 1/4" quick change chuck 3/8" square drive 1/2" square drive 3/4" square drive 450 225 900 450 1" square drive
Page 1 and 2: Industrial Power Tools 2010-11 The
Page 3 and 4: 2 Whatever your business, we can ad
Page 5 and 6: 4 Our commitment to your productivi
Page 7 and 8: 6 Quality, every step of the way At
Page 9 and 10: 8 Five steps to zero-fault fastenin
Page 11 and 12: 10 Your guide to the catalogue Acce
Page 13 and 14: Pneumatic Assembly Tools Introducti
Page 15 and 16: Pneumatic Screwdrivers Introduction
Page 17 and 18: Pneumatic Screwdrivers Pistol Grip
Page 19 and 20: Pneumatic Screwdrivers Pistol Grip
Page 21 and 22: Pneumatic Screwdrivers Straight Mod
Page 23 and 24: Pneumatic Screwdrivers Angle Models
Page 25 and 26: Pneumatic Screwdrivers Accessories
Page 27 and 28: Impact Wrenches Selection Guide =
Page 29 and 30: Impact Wrenches Pistol Grip Models
Page 31 and 32: Impact Wrenches Accessories LMS, LT
Page 33: Impact Wrenches Accessories LMS, LT
Page 37 and 38: Hydraulic Impulse Nutrunners Pistol
Page 39 and 40: Hydraulic Impulse Nutrunners Straig
Page 41 and 42: Hydraulic Impulse Nutrunners Access
Page 43 and 44: Controlled Impulse Nutrunners Intro
Page 45 and 46: Controlled Impulse Nutrunners Acces
Page 47 and 48: Pneumatic Nutrunners Introduction -
Page 49 and 50: Pneumatic Nutrunners Angle Nutrunne
Page 55 and 56: Pneumatic Nutrunners Accessories An
Page 63 and 64: Fast, flexible and user-friendly Th
Page 65 and 66: Shut-off Straight Nutrunners Air Re
Page 67 and 68: Straight Nutrunners Accessories Opt
Page 69 and 70: Non Shut-off Pistol Grip Nutrunners
Page 71 and 72: Shut-off Pistol Grip Nutrunners For
Page 73 and 74: Pistol Grip Nutrunners Accessories
Page 75 and 76: Battery Assembly Tools Contents Pag
Page 77 and 78: Powerful, durable and highly operat
Page 79 and 80: BCP Accessories Optional Accessorie
Page 81 and 82: BTV Accessories Optional Accessorie
Page 83 and 84: Tensor STB Nutrunners - Transduceri
Page 85 and 86:
ETO STB Tensor STB Tube Nut In-Line
Page 87 and 88:
Electric Assembly Tools and Systems
Page 89 and 90:
Safety Atlas Copco wants everyone t
Page 91 and 92:
Brushless clutch type EBL Designed
Page 93 and 94:
ETD, ETF MicroTorque Ultra low-torq
Page 95 and 96:
MicroTorque Accessories Vacuum adap
Page 97 and 98:
ETD SL l ETD SL is a very compact s
Page 99 and 100:
Tensor Accessories Optional Accesso
Page 101 and 102:
Page 103 and 104:
Electric Nutrunners Tensor Overview
Page 105 and 106:
Tensor DS Straight Models ETD DS l
Page 107 and 108:
Tensor DS Pistol Grip Models ETP DS
Page 109 and 110:
Tensor DS Tube Nut In-Line tube nut
Page 111 and 112:
Tensor S Straight Models ETD S l ET
Page 113 and 114:
Tensor ST Angle Models ETV ST l ETV
Page 115 and 116:
Tensor ST Angle Models Square drive
Page 117 and 118:
Tensor ST Straight Models Square dr
Page 119 and 120:
Tensor ST Crowfoot In-Line crowfoot
Page 121 and 122:
Tensor STR Angle Models ETV STR l S
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Introduction - Controllers and Soft
Page 131 and 132:
DS/DL Drive Controllers Drive funct
Page 133 and 134:
Power Focus 4000 series Controllers
Page 135 and 136:
Introduction - Quality Integrated F
Page 137 and 138:
Quality Integrated Fastening Statio
Page 139 and 140:
Quality Integrated Fastening Statio
Page 141 and 142:
Tool Accessories Contents Page Torq
Page 143 and 144:
SM A2 Parallel Arm SM A2 - Parallel
Page 145 and 146:
SML Linear Arm SML - Linear torque
Page 147 and 148:
GHP Torque Arms MicroTorque GHP - T
Page 149 and 150:
Optional Accessories for SM A2 and
Page 151 and 152:
Optional Accessories for GHP MicroT
Page 153 and 154:
Torx bits Application: For Torx scr
Page 155 and 156:
TorxPlus bits Application: For Torx
Page 157 and 158:
Power socket 3/4" square drive 3/4"
Page 159 and 160:
Fixtured Applications Contents Page
Page 161 and 162:
Nutrunners to match your needs The
Page 163 and 164:
QST Fixtured Nutrunners Travel Torq
Page 165 and 166:
QST Accessories Optional Accessorie
Page 167 and 168:
ETX Accessories Optional Accessorie
Page 169 and 170:
Power MACS 4000 Controllers Power M
Page 171 and 172:
System Guide Controllers Easy-to-bu
Page 173 and 174:
Power Focus 4000 series Controllers
Page 175 and 176:
Quality Assurance in Tightening Con
Page 177 and 178:
ACTA 400 Torque Readouts ACTA 400 T
Page 179 and 180:
QRTT/IRTT-B Transducers QRTT Trandu
Page 181 and 182:
MRTT-B Transducers MRTT-B Manual wr
Page 183 and 184:
MicroTorque Accessories Torque anal
Page 185 and 186:
STwrench Functionality Overview Fun
Page 187 and 188:
STwrench Accessories IRC Modules Tw
Page 189 and 190:
600 - 700 B A H B H L L 600 - 700 W
Page 191 and 192:
JSB Test Benches BLM Joint Simulato
show all

Industrial Power Tools 2010-11 - Atlas Copco

Create successful ePaper yourself

Delete template?

Save as template?