M Series Pin and Socket Connectors
M Series Pin and Socket Connectors
M Series Pin and Socket Connectors
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Dimensions are shown for reference<br />
purposes only.<br />
M <strong>Series</strong><br />
<strong>Pin</strong> <strong>and</strong> <strong>Socket</strong> <strong>Connectors</strong><br />
Cable-to-Panel (Continued)<br />
1. Confirm that Application E (at left) most closely meets<br />
your requirements. (Other applications are shown on<br />
pages 10-17 <strong>and</strong> 20 through 25.)<br />
2. Find the appropriate column for the number of positions<br />
required.<br />
3. Select part numbers required for the application listed<br />
in the column below the number of positions.<br />
3. If a part number is not listed for a particular item, it is<br />
not available.<br />
3. If more than one part number is listed for a particular<br />
hardware item, choose the one which best fits your<br />
application.<br />
4. Dimensional information is available on the indicated<br />
pages under description column.<br />
5. Select Contacts: Type II (page 30), Type III+ (pages 31<br />
through 35) or Subminiature Coaxial (pages 40, 41).<br />
Dimensions are in inches <strong>and</strong> millimeters<br />
unless otherwise specified.<br />
Values in brackets are metric equivalents.<br />
Specifications subject to change. Technical Support Center<br />
1-800-522-6752<br />
www.tycoelectronics.com<br />
Catalog 82003<br />
Revised 3-01<br />
Special application housings <strong>and</strong> posted housings may<br />
be substituted for these st<strong>and</strong>ard housings. See Special<br />
Application <strong>and</strong> Posted <strong>Connectors</strong> Sections.<br />
This cable-to-panel application utilizes locking springs,<br />
strain relief clamps, a pin hood for pin protection <strong>and</strong> guide<br />
hardware.<br />
The 34 <strong>and</strong> 50 position connectors can be used with either<br />
center or corner guide hardware. If center guide hardware<br />
is used, an additional four 4-40 screws, nuts <strong>and</strong> lockwashers<br />
are required to secure the locking springs. Corner<br />
guides require four guide pins <strong>and</strong> four guide sockets for<br />
each mated pair of connectors.<br />
41 50<br />
Number of Positions<br />
75 104 104 CF 160 CF<br />
Component Description<br />
202135-2<br />
201302-1<br />
202135-4<br />
201302-3<br />
—<br />
—<br />
201358-1<br />
200277-2<br />
201358-3<br />
200277-4<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
1-201692-6<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
Plug Block<br />
Receptacle Block<br />
Plug Block<br />
Receptacle Block<br />
Plug Block<br />
Receptacle Block<br />
Phenolic<br />
Diallyl Phthalate<br />
Polyester<br />
STANDARD<br />
HOUSINGS<br />
Pages 44 to 51<br />
—<br />
—<br />
—<br />
201182-1<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
Long<br />
Short<br />
Nickel Plated Steel<br />
STRAIN<br />
RELIEF<br />
201766-1<br />
—<br />
201847-1<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
Long<br />
Short<br />
Stainless Steel<br />
CLAMPS<br />
Page 88<br />
200389-2<br />
200390-2<br />
—<br />
200389-2<br />
200390-2<br />
200833-2<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
Center Male<br />
Center Female<br />
Corner Male<br />
Stainless Steel<br />
GUIDE<br />
HARDWARE<br />
Page 81<br />
— 200835-2 — — — — Corner Female<br />
201921-1<br />
201922-1<br />
201925-1<br />
201926-1<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
Male—Nickel Plated Spring Steel<br />
Female—Stainless Steel<br />
LOCKING SPRINGS1<br />
Page 80<br />
— — — — — — Internal Open End Nickel Plated Steel<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
—<br />
Internal Closed End<br />
External Closed End<br />
Nickel Plated Steel<br />
Al Iridite<br />
PIN HOODS<br />
Pages 82 <strong>and</strong> 83<br />
— — — — — — External Closed End Nickel Plated Steel<br />
19