APPWD Schedule of Rates for Road and Bridges - Arunachalpwd.org

Item
No.
8.35
8.36
8.38
8.40
8.43
8.44
A
B
C
Descriptions
Summary of Rate Analysis
Road Markers/Road Stud with Lense Reflector (Providing and fixing of road
stud 100x 100 mm, die cast in aluminium, resistant to corrosive effect of salt and
grit, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling
hole 30 mm upto a depth of 60 mm and bedded in a suitable bituminous grout or
epoxy mortar, all as per BS 873 part 4:1973)
Traffic Cone (Provision of red fluorescent with white reflective sleeve traffic cone
made of low density polyethylene (LDPE) material with a square base of 390 x 390
x 35 mm and a height of 770 mm, 4 kg in weight, placed at 1.5 m interval, all as per
BS 873)
Rumble Strips (Provision of 15 nos rumble strips covered with premix bituminous
carpet, 15-20 mm high at center, 250 mm wide placed at 1 m center to center at
approved locations to control speed, marked with white strips of road marking
paint.)
High Mast Pole Lighting at Interchanges and Flyovers (Providing and erecting
a high mast pole lighting with 30 m high hot dip galvanised mast designed to
withstand forces exerted with wind speeds of 180 km per hour with 3 seconds gust,
as per IS:875 (Part 3) - 1978, fitted with a base flange, door at the base of mast
with heavy duty internal lock, lantern carriage, suitable winching arrangement for
safe working load of 750 kg and high powered electrically driven power tools for
raising and lowering of lantern carriage, flexible 8 core electric cable, lightening
conductor, earthing terminal, and fixing 2 nos aviation obstruction lights on top of
the mast, all complete as per approved design and drawings This is a specialised
work and is generally done by firms who specialise in such jobs. The detailed
designs and estimates are submitted by the firms alongwith their tender for checks
by the Department. The cost of this work is required to be worked out based on
approved design, drawings and estimate of the lowest tender. A separate contract
for this work is concluded as the contractors for road and bridge works generally don
Portable Barricade in Construction Zone (Installation of a steel portable
barricade with horizontal rail 300 mm wide, 2.5 m in length fitted on a 'A' frame
made with 45 x 45 x 5 mm angle iron section, 1.5 m in height, horizontal rail
painted (2 coats) with yellow and white stripes, 150 mm in width at an angle of 450,
'A' frame painted with 2 coats of yellow paint, complete as per IRC:SP:55-2001 )
Permanent Type Barricade in Construction Zone
With Steel Components (Construction of a permanent type barricade made of
steel components, 1.5 m high from road level, fitted with 3 horizontal rails 200
mm wide and 4 m long on 50 x 50 x 5 mm angle iron vertical support, painted
with yellow and white strips, 150 mm in width at an angle of450, complete as per
IRC:SP:55-2001 )
With Wooden Components (Construction of a permanent type barricade made
of wooden components, 1.5 m high from road level, fitted with 3 horizontal
planks 200 mm wide and 3.66 m long on 100 x 100mm wooden vertical post,
painted with yellow and white striups, 150 mm in width at an angle of450,
complete as per IRC:SP:55-2001 )
With Bricks (Construction of a permanent type barricade made with brick work
in mud mortar, 1.5 m high, 4 m long, 600 mm thick, plastered with cement
mortar 1:6, painted with yellow and white strips)
47
Unit Rate
each 535.00
each 1212.00
sqm
each 2518.00
each 4050.00
each 2481.00
each 9792.00