CADD Engineering Standards - Ohio Department of Transportation
CADD Engineering Standards - Ohio Department of Transportation CADD Engineering Standards - Ohio Department of Transportation
January 18, 2013 The XS Reports dialog shown below is opened. Select Multi-Line to access the Multi-Line Report dialog shown below. 108 ODOT CADD Engineering Standards
January 18, 2013 Select the symbology box to the right of the XS Elements label to identify the cross section elements that make up the proposed finished grade. If ODOT criteria files are used to generate the proposed cross section graphics, the following levels should be selected within the Candidate Elements dialog: XS_P_Ditch_Bottom XS_P_Finished_Grade XS_P_Finished_Grade_Seeded XS_P_Pavt_Surface XS_P_Shoulder_Surface Note: Additional levels may need to be selected depending on how the cross sections graphics were drawn. Use the Match button on the Candidate Elements dialog to select the desired cross section elements. Set the Output Format to X,Y,ELEV,OFFSET. Check on the 5-Point option. Key-in the name of the ASCII File for the cross section report. Select the Add icon to the right of the Multi-Line Report dialog to add the report to the list. The report will show up in the list box in the center of the dialog as shown in the example on the previous page. ODOT CADD Engineering Standards 109
- Page 65 and 66: January 18, 2013 Figure 302-1 Minor
- Page 67 and 68: January 18, 2013 Figure 302-3 Proje
- Page 69 and 70: January 18, 2013 Figure 302-9 Struc
- Page 71 and 72: 303 References 303.1 General Januar
- Page 73 and 74: 303.2.1 Types of Models January 18,
- Page 75 and 76: 303.2.3 Model Properties January 18
- Page 77 and 78: 303.2.4 Referencing Models January
- Page 79 and 80: January 18, 2013 Final plan sheets
- Page 81 and 82: 304.3 File Name Format January 18,
- Page 83 and 84: Supplemental Description Examples:
- Page 85 and 86: January 18, 2013 4. To save these c
- Page 87 and 88: Figure 304-1 File Name Type Codes B
- Page 89 and 90: SIGNAL SHEETS Notes - CN General Su
- Page 91 and 92: 306.2 GEOPAK COGO Element Names Jan
- Page 93 and 94: COGO Right of Way Elements Chains R
- Page 95 and 96: (1) Project Name: For this example,
- Page 97 and 98: 400 PLOTTING 401 General 401.1 Gene
- Page 99 and 100: 401.2.3 Shading The following are o
- Page 101 and 102: 502.2 Saved View January 18, 2013 W
- Page 103 and 104: Figure 503-2 504 CADD File Requirem
- Page 105 and 106: January 18, 2013 A sample ASCII rep
- Page 107 and 108: 504.3 Vertical Alignment ASCII Repo
- Page 110 and 111: January 18, 2013 Each horizontal al
- Page 112 and 113: January 18, 2013 504.6 Monumentatio
- Page 114 and 115: January 18, 2013 Left Offset/Right
- Page 118 and 119: January 18, 2013 Select the Apply b
- Page 120 and 121: Appendix A - CADD Information Table
- Page 122 and 123: Appendix A - CADD Information Table
- Page 124 and 125: Appendix A - CADD Information Table
- Page 126 and 127: Appendix A - CADD Information Table
- Page 128 and 129: Appendix A - CADD Information Table
- Page 130 and 131: Appendix A - CADD Information Table
- Page 132 and 133: Appendix A - CADD Information Table
- Page 134 and 135: Appendix A - CADD Information Table
- Page 136 and 137: Appendix A - CADD Information Table
- Page 138 and 139: Appendix A - CADD Information Table
- Page 140 and 141: Appendix A - CADD Information Table
- Page 142 and 143: Appendix A - CADD Information Table
- Page 144 and 145: Appendix A - CADD Information Table
- Page 146 and 147: Appendix A - CADD Information Table
- Page 148 and 149: Appendix A - CADD Information Table
- Page 150 and 151: Appendix A - CADD Information Table
- Page 152 and 153: Appendix A - CADD Information Table
- Page 154 and 155: Appendix A - CADD Information Table
- Page 156 and 157: Appendix A - CADD Information Table
- Page 158 and 159: Appendix A - CADD Information Table
- Page 160 and 161: Appendix A - CADD Information Table
- Page 162 and 163: Appendix A - CADD Information Table
- Page 164 and 165: Appendix A - CADD Information Table
January 18, 2013<br />
The XS Reports dialog shown below is opened.<br />
Select Multi-Line to access the Multi-Line Report dialog shown below.<br />
108 ODOT <strong>CADD</strong> <strong>Engineering</strong> <strong>Standards</strong>