Application Manual K-FLEX IC-CLAD 1109.pdf

More documents

Recommendations

Info

The K-FLEX pre-shaped flanges are formed by a sectioned body of elastomeric insulation already covered with IC CLAD sheet, in black or silver.They include an adhesive overlap for fixing the two parts along the seperating cut. A A) Glue the cut elastomeric edges with K420 adhesive. B) Apply the two perforated parts on the flange keeping in mind that the overlappings are part of the upper section, in order to turn the superimposition against water. C) Close the glued elastomer sides to seal the pre-shaped part. Remove the protective silicone paper of the overlap and fix the closure of the finishing. K-FLEX IC CLAD - FLANGE Finishing with K-FLEX pre-shaped flange already finished with IC CLAD sheet KEY: K 420 adhesive Marine silicone Measurements Actions B C IC CLAD Application guide 04/04 - Engl. IC CLAD - FLANGES 11 5
D) Fix with the specific IC CLAD adhesive tape all the visible joints, including those of the pre-shaped parts. E) For external applications, if necessary, seal the edges of the tapes with marine silicone. K-FLEX IC CLAD - FLANGE Finishing with K-FLEX pre-shaped flange already finished with IC CLAD sheet KEY: K 420 adhesive Marine silicone Measurements Actions D E IC CLAD Application guide 04/04 - Engl. IC CLAD - FLANGES 12 5
Page 1 and 2:
Via Leonardo Da Vinci, 36 - 20040 R
Page 3 and 4:
K-FLEX IN CLAD APPLICATION GUIDE IN
Page 5 and 6:
K-FLEX IC CLAD is a flexible closed
Page 9 and 10:
NO SI K-FLEX IC CLAD Practical sugg
Page 11 and 12:
K-FLEX IC CLAD APPLICATION GUIDE IN
Page 13 and 14:
For procedure details reletive to t
Page 15 and 16:
Laying of the two consecutive K-FLE
Page 17 and 18:
+5 cm Circumference of the insulate
Page 19 and 20:
A) Place sheet II in a way to overl
Page 21 and 22:
Preparation of a length of tube A)
Page 23 and 24:
A) Glue the overlap with K 420 adhe
Page 25 and 26:
Laying of tube II B C K-FLEX IC CLA
Page 27 and 28:
A) Glue with K 420 adhesive the lon
Page 29 and 30:
A) The finishing of the product is
Page 31 and 32:
A With the same procedure illustrat
Page 33 and 34:
K-FLEX IC CLAD APPLICATION GUIDE IN
Page 35 and 36:
For procedure details reletive to t
Page 37 and 38:
Laying of the two consecutive K-FLE
Page 39 and 40:
+5 cm Circumference of the insulate
Page 41 and 42:
A) Place sheet II in a way to overl
Page 43 and 44: Preparation of a length of tube A)
Page 45 and 46: A) Glue the overlap with K 420 adhe
Page 47 and 48: Laying of tube II B C K-FLEX IC CLA
Page 49 and 50: A) Glue with K 420 adhesive the lon
Page 51 and 52: A) The finishing of the product is
Page 53 and 54: A With the same procedure illustrat
Page 55 and 56: K-FLEX IC CLAD APPLICATION GUIDE IN
Page 57 and 58: For the application procedures of K
Page 59 and 60: How to arrange the finishing shapes
Page 61 and 62: How to fix the joints of the IC CLA
Page 63 and 64: How to fix the joints of the IC CLA
Page 65 and 66: A) Remove the protective silicone p
Page 69 and 70: K-FLEX IC CLAD - “T-piece” insu
Page 71 and 72: K-FLEX IC CLAD - “T-piece” “T
Page 73 and 74: K-FLEX IC CLAD - “T-piece” “T
Page 75 and 76: A K-FLEX IC CLAD - “T-piece”
Page 77 and 78: The pre-shaped and pre-cut “T-pie
Page 79 and 80: F) Glue the elastomer edges with co
Page 81 and 82: L) Remove protective silicone paper
Page 83 and 84: IC CLAD Application guide 04/04 - E
Page 85 and 86: INDEX Flanges: Insulation and finis
Page 87 and 88: Finishing of adjacent tubes • Pre
Page 89 and 90: Finishing of the flange body B) Cut
Page 91 and 92: A) Cut a section of K-FLEX IC / IN
Page 93: G) Prepare a strip of IC / IN CLAD
Page 99 and 100: For the detailed preparation of the
Page 101 and 102: • Cut out a ring, the diameter of
Page 103 and 104: K-FLEX IC CLAD - VALVES Finishing o
Page 105 and 106: • Measure the indicated diameters
Page 107 and 108: K-FLEX IC CLAD - VALVES Valve finis
Page 109 and 110: K-FLEX IC CLAD - VALVES Valve finis
Page 111 and 112: 1) Cut out the covering of the valv
Page 119 and 120: The pre-shaped K-FLEX IC CLAD valve
Page 121 and 122: • Fix all the joints, including t
Page 123 and 124: INDEX Reducers: insulation and fini
Page 125 and 126: 3 2 1 K-FLEX IC CLAD Finishing of r
Page 129 and 130: For the detailed installation of K-
Page 131 and 132: 1 2 K-FLEX IC CLAD - SMALL AND MEDI
Page 133 and 134: Finishing of the accessory parts
Page 135 and 136: As previously illustrated for the b
Page 137 and 138: INDEX Large tanks: insulation and f
Page 139 and 140: Insulation of the tank’s wall K-F
Page 141 and 142: Finishing of the tank’s wall •
Page 143 and 144: Finishing of the tank’s roof K-FL
Page 145 and 146:
If necessary, accurately seal the e
Page 147 and 148:
Covering the wall of the tank For t
Page 149 and 150:
Covering of the tank’s wall • T
Page 151 and 152:
Covering the top of the tank’s ro
Page 153 and 154:
Preparation of the internal coverin
show all

Application Manual K-FLEX IC-CLAD 1109.pdf

Create successful ePaper yourself

Delete template?

Save as template?