Application Manual K-FLEX IC-CLAD 1109.pdf

More documents

Recommendations

Info

Laying of tube I A) Place the prepared sheet on the piping to check the dimensions. Turn the closure of the overlap against water. B) Glue the joining edges of the elastomerico layer with K 420 adhesive. A) Join the edges of the elastomer pressing carefully to obtain an even closure without stretch marks. KEY: K 420 adhesive Marine silicone Measurements Actions K-FLEX IN CLAD - TUBE Use of the K-FLEX sheet with IC CLAD finishing already applied IC CLAD guida per l’applicazione 03/04 - Engl. IC CLAD - TUBES 12 2
A) Glue the overlap with K 420 adhesive. A) Close the overlap using careful pressure to obtain an even closure without stretch marks. B) Fix the joints with a strip of specific IC CLAD adhesive tape. KEY: K 420 adhesive Marine silicone Measurements Actions K-FLEX IC CLAD - TUBE Use of the K-FLEX sheet with IC CLAD finishing already applied IC CLAD guida per l’applicazione 03/04 - Engl. IC CLAD - TUBES 13 2
Page 1 and 2: Via Leonardo Da Vinci, 36 - 20040 R
Page 3 and 4: K-FLEX IN CLAD APPLICATION GUIDE IN
Page 5 and 6: K-FLEX IC CLAD is a flexible closed
Page 9 and 10: NO SI K-FLEX IC CLAD Practical sugg
Page 11 and 12: K-FLEX IC CLAD APPLICATION GUIDE IN
Page 13 and 14: For procedure details reletive to t
Page 15 and 16: Laying of the two consecutive K-FLE
Page 17 and 18: +5 cm Circumference of the insulate
Page 19 and 20: A) Place sheet II in a way to overl
Page 21: Preparation of a length of tube A)
Page 25 and 26: Laying of tube II B C K-FLEX IC CLA
Page 27 and 28: A) Glue with K 420 adhesive the lon
Page 29 and 30: A) The finishing of the product is
Page 31 and 32: A With the same procedure illustrat
Page 35 and 36: For procedure details reletive to t
Page 37 and 38: Laying of the two consecutive K-FLE
Page 39 and 40: +5 cm Circumference of the insulate
Page 41 and 42: A) Place sheet II in a way to overl
Page 43 and 44: Preparation of a length of tube A)
Page 45 and 46: A) Glue the overlap with K 420 adhe
Page 47 and 48: Laying of tube II B C K-FLEX IC CLA
Page 49 and 50: A) Glue with K 420 adhesive the lon
Page 51 and 52: A) The finishing of the product is
Page 53 and 54: A With the same procedure illustrat
Page 57 and 58: For the application procedures of K
Page 59 and 60: How to arrange the finishing shapes
Page 61 and 62: How to fix the joints of the IC CLA
Page 63 and 64: How to fix the joints of the IC CLA
Page 65 and 66: A) Remove the protective silicone p
Page 69 and 70: K-FLEX IC CLAD - “T-piece” insu
Page 71 and 72: K-FLEX IC CLAD - “T-piece” “T
Page 73 and 74:
K-FLEX IC CLAD - “T-piece” “T
Page 75 and 76:
A K-FLEX IC CLAD - “T-piece”
Page 77 and 78:
The pre-shaped and pre-cut “T-pie
Page 79 and 80:
F) Glue the elastomer edges with co
Page 81 and 82:
L) Remove protective silicone paper
Page 83 and 84:
IC CLAD Application guide 04/04 - E
Page 85 and 86:
INDEX Flanges: Insulation and finis
Page 87 and 88:
Finishing of adjacent tubes • Pre
Page 89 and 90:
Finishing of the flange body B) Cut
Page 91 and 92:
A) Cut a section of K-FLEX IC / IN
Page 93 and 94:
G) Prepare a strip of IC / IN CLAD
Page 95 and 96:
D) Fix with the specific IC CLAD ad
Page 97 and 98:
K-FLEX IC CLAD APPLICATION GUIDE IN
Page 99 and 100:
For the detailed preparation of the
Page 101 and 102:
• Cut out a ring, the diameter of
Page 103 and 104:
K-FLEX IC CLAD - VALVES Finishing o
Page 105 and 106:
• Measure the indicated diameters
Page 107 and 108:
K-FLEX IC CLAD - VALVES Valve finis
Page 109 and 110:
K-FLEX IC CLAD - VALVES Valve finis
Page 111 and 112:
1) Cut out the covering of the valv
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
The pre-shaped K-FLEX IC CLAD valve
Page 121 and 122:
• Fix all the joints, including t
Page 123 and 124:
INDEX Reducers: insulation and fini
Page 125 and 126:
3 2 1 K-FLEX IC CLAD Finishing of r
Page 127 and 128:
K-FLEX IC CLAD APPLICATION GUIDE IN
Page 129 and 130:
For the detailed installation of K-
Page 131 and 132:
1 2 K-FLEX IC CLAD - SMALL AND MEDI
Page 133 and 134:
Finishing of the accessory parts
Page 135 and 136:
As previously illustrated for the b
Page 137 and 138:
INDEX Large tanks: insulation and f
Page 139 and 140:
Insulation of the tank’s wall K-F
Page 141 and 142:
Finishing of the tank’s wall •
Page 143 and 144:
Finishing of the tank’s roof K-FL
Page 145 and 146:
If necessary, accurately seal the e
Page 147 and 148:
Covering the wall of the tank For t
Page 149 and 150:
Covering of the tank’s wall • T
Page 151 and 152:
Covering the top of the tank’s ro
Page 153 and 154:
Preparation of the internal coverin
show all

Application Manual K-FLEX IC-CLAD 1109.pdf

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?